Table of Contents
Advertisement
Available languages
Available languages
IOR-232POE. This output is a potential-free relay with a nor-
mally open contact (power rating of 30 V/ 1 A) to which an
acoustic or optical alarm signal device, for example, can be
connected.
6.5 RS485 interface for PTZ control
– model IOR-232POE only –
Connect cameras where pan, tilt and zoom can only be
adjusted via an RS-485 interface to the screw terminals
"RS485" (17). Connect the contacts "−" (= RS-485-A) and
"+" (= RS-485-B") to the corresponding contacts of the first
camera. An additional camera can be connected in parallel to
the connections of the first camera etc. until all cameras are
connected in a chain. To reduce interference, twisted cables
should be used. At the final camera of the chain, terminate
the two cables with a 120 Ω resistor (this is often possible by
means of a switch at the camera).
To be able to address the cameras independently from
the recorder, assign an individual address to each camera
(via a menu of the camera). At the recorder, set the address
to be used to control the respective camera as well as the
transmission parameters and protocol the camera requires
(chapter 7.13).
6.6 Network
For remote control and when the camera is integrated into a
network, connect the jack WAN (7) of the recorder to a local
network or to a router. Always observe the data security notes
in chapter 3!
6.7 Power supply
For the models IOR-204 and IOR-208, connect the power
supply unit to the jack "48 V⎓" (15) and to a mains socket
(230 V/ 50 Hz).
For the model IOR-232POE, use the mains cable provided
to connect the mains jack (18) to a mains socket (230 V/ 50 Hz).
6.7.1 Inserting / Replacing batteries
of the remote control
To insert the batteries (2 × 1.5 V, size AAA), remove the battery
compartment cover on the rear of the remote control. Insert
the batteries as indicated in the compartment and then close
the cover.
If the remote control is not used for a longer time, remove
the batteries as a precaution so that the remote control will
not be damaged in case the batteries should leak.
Never put batteries in the household waste. To protect
the environment, always take them to a special waste
disposal, e. g. collection container at your retailer.
7
Setting the Recorder
into Operation
When the
cameras
monitor
mouse
power supply unit of the recorder
have been connected, switch on the recorder with the rocker
switch (14) on the rear. After a few seconds, the MONACOR
logo will appear on the monitor connected:
After approx. 30 seconds, the screen will be dark for approx.
30 seconds; then the start page with the "Startup Wizard"
will appear:
Camera
03/04/2018 09:53:46
CH1
Startup Wizard
R
Don't show this window next time.
No Camera
No Camera
Fig. 7-1 Start page: The "Startup Wizard" is displayed; the number of
fields available for the camera images depends on the recorder
model used
7.1 Setting the menu language
The menu language is factory-set to German. To change the
menu language:
1) When a warning appears after switch-on, click
2) In the window "Startup Wizard", click the button
"Schließen". The confirmation box "Are you sure you want
to cancel Startup Wizard?" will appear. Click "OK".
3) To show the toolbar, press the right mouse button or move
the mouse pointer to the centre of the lower edge of the
screen:
Fig. 7-2 Toolbar
4) Click the icon
HAUPTMENÜ (MAIN MENU).
Parameter
Aufnahme Suche
Gerät
Anzeige
Kamera
arbeit State
IP Camera
IP CH1
Live
IP CH2
IP CH3
Video
IP CH4
Image Control
Privat Zone
Video
Auto Assign IP to Camera(s)
Capture
Netzwerk
Alarm
Fig. 7-3 Hauptmenü (main menu)
03/04/2018 09:53:46
CH2
R
03/04/2018 09:53:46
CH3
R
Welcome to use the wizard of setup
No Camera
×
Cancel
Next
No Camera
No Camera
×
to close it.
i
System
Erweitert
Herunterfahren
P Adresse/Domain Nam
Subnet Maske
10.10.25.151
255.255.0.0
10.10.25.152
255.255.0.0
Channel Delete
Add All
User-defined Add
Total band width:60Mbps, used band width:10.5bps
i
i
PORT
M
9988
9988
Schließen
37
Advertisement
Chapters
Table of Contents
