Table Of High-Level Instructions - Panasonic FP-X0 L14R User Manual

14.3 Table of High-level Instructions

The high-level instructions are expressed by the prefixes "F" or "P" with numbers. For most of the high-level
instructions, "F" and "P" types are available. The differences between the two types are explained as follows:
- Instructions with the prefix "F" are executed in every scan while its trigger is in the on.
- Instructions with the prefix "P" are executed only when the leading edge of its trigger is detected.
For the FP0/FP0R/FPΣ/FP-X, the P type high-level instructions are not available.
Num-
Name
ber
Data transfer instructions
F0 16-bit data
P0 move
F1 32-bit data
P1 move
F2 16-bit data
P2 invert and
move
F3 32-bit data
P3 invert and
move
F4 Reading of
P4 head word No.
of the
specified slot
F5 Bit data move BTM
P5
F6 Hexadecimal
P6 digit (4-bit)
data move
F7 Two 16-bit
P7 data move
F8 Two 32-bit
P8 data move
F10 Block move
P10
F11 Block copy
P11
F12 Data read from
EEP-ROM
P13 Data write to
EEP-ROM
F12 Data read from
F-ROM
P13 Data write to
F-ROM
F12 Data read from
P12 IC card
F13 Data write to
P13 IC card
F14 Program read
P14 from IC
memory card
: Available, : Not available,
*1) This instruction is available for FP2/FP2SH Ver. 1.5 or later.FP10SH cannot be used
*2) This instruction is available for FP0 Ver. 2.0 or later and FP-e.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Ope-
Boo-lean
rand
MV S, D (S)→(D)
PMV
DMV S, D (S+1, S)→(D+1, D)
PDMV
MV S, D
PMV/ (S)→(D)
DMV/ S, D
PDMV/ (S+1, S)→(D+1, D)
GETS S, D The head word No. of the specified slot is
PGETS read.
S, n, D The specified one bit in "S" is transferred to
PBTM the specified one bit in "D". The bit is
specified by "n".
DGT S, n, d The specified one digit in "S" is transferred
PDGT to the specified one digit in "D". The digit is
specified by "n".
MV2 S1, S2, (S1)→(D),
PMV2 D (S2)→(D+1)
DMV2 S1, S2, (S1+1, S1)→(D+1, D),
PDMV2 D (S2+1, S2)→(D+3, D+2)
BKMV S1, S2, The data between "S1" and "S2" is
PBKMV D transferred to the area starting at "D".
COPY S, D1, The data of "S" is transferred to the all area
PCOPY D2 between "D1" and "D2".
ICRD S1, S2, The data stored in the expansion memory
D of the EEP-ROM specified by "S1" and "S2"
are transferred to the area starting at "D".
PICWT S1, S2, The data specified by "S1" and "S2" are
D transferred to the EEP-ROM starting at "D".
ICRD S1, S2, The data stored in the expansion memory
D of the F-ROM specified by "S1" and "S2"
are transferred to the area starting at "D".
PICWT S1, S2, The data specified by "S1" and "S2" are
D transferred to the F-ROM starting at "D".
ICRD S1, S2, The data stored in the expansion memory
PICRD D of the IC card specified by "S1" and "S2"
are transferred to the area starting at "D".
ICWT S1, S2, The data specified by "S1" and "S2" are
PICWT D transferred to the IC card expansion
memory area starting at "D".
PGRD S The program specified using "S" is
PPGRD transferred into the CPU from IC memory
card and executes it.
: Not available partially
Description
5
7
5
7
5
*1
7
7
7
11
7
7
11
*2
11
*2
11
11
11
11
3
*1