Panasonic FP-X0 L14R User Manual page 201

Item
No. of interrupt programs
Sampling trace
Comment storage
PLC link function
Constant scan
Password
Upload protection
Self-diagnosis function
Program editing during RUN
High-speed counter
Note3) Note4)
Pulse output/
Note4)
PWM output
Pulse catch input/interrupt
input
Periodical interrupt
Analog input
Clock/calender
Backup by F12,
P13 instructions
Flash
ROM
Automatic backup
backup
when power is cut
Note5)
off
Battery backup
Note1) The number of points actually available for use is determined by the hardware configuration.
Note2) The number of points can be increased by using an auxiliary timer.
Note3) This is the specification when the rated input voltage is 24 V DC at 25 °C. The frequency will decrease
depending on voltage, temperature or usage condition.
Note4) For information on the restrictions on combinations, refer to "7.2 Function Specifications and Restricted Items".
Note5) Writing is available up to 10000 times. Areas to be held and not held can be specified using the system
registers.
Note6) Refresh time of FP0 expansion unit
8-point unit
16-point unit
32-point unit
64-point unit
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
L14
Input 8 programs, periodical interrupt 1 program
Not available
All comments including I/O comments, explanatory notes, interlinear comments
can be stored. (Backup battery is not necessary. 328 kbytes)
Not available
0.5 ms unit: 0.5 ms to 600 ms
Available (4 digits, 8 digits)
Available
Such as watchdog timer, program syntax check
Available
Single-phase 4 chs (Max. 20 kHz) or
2-phase 2chs (Max. 20kHz)
Pulse output: 1 ch Pulse output: 2 chs
(Max. 20 kHz) or (Max. 20 kHz) or
PWM output: 1 ch PWM output: 2 chs
(Max. 1.6 kHz) (Max. 1.6 kHz)
8 points (Input of main unit: 8 points X0 to X7)
(including high-speed counter and interrupt input)
0.5 ms unit: 0.5 ms to 1.5 s, 10 ms unit: 10 ms to 30 s
None
None
Data register (2500 words)
Counter: 6 points (C250 to C255)
Internal relay: 5 points (WR58 to WR62)
Data register:300 words (DT2200 to
DT2499)
Not available
No. of units used x 0.8 ms
No. of units used x 1.0 ms
No. of units used x 1.3 ms
No. of units used x 1.9 ms
Descriptions
L30 L40
Available
Available
Single-phase 4 chs (Max. 50 kHz) or
2-phase 2chs (Max. 20kHz)
Pulse output: 2 chs (Max. 50 kHz) or
PWM output: 2 chs (Max. 3 kHz)
2 chs, 10-bit resolution The following
input can be used individually for each
channel.
[Potentiometer (Volume) input]
Min. potentiomenter resistance: 5kΩ
Resolution 10 bits (K0 to K1000):
Accuracy±1.0% F.S. + External
resistance accuracy
[Thermister input]
Allowable thermister resistance
(External thermister min.
resistance+External resistance>2kΩ)
Resolution 10 bits (K0 to K1023):
Accuracy±1.0% F.S. + External
thermister accuracy
[Voltage input]
Absolute max. input voltage: 10 V
Resolution 10 bits (K0 to K1023):
Accuracy ± 2.5% F.S. (F.S. = 10 V)
Built in
Data register (8192 words)
Counter:16 points (C1008 to C1023)
Internal relay:8 points (WR248 to
WR255)
Data register: 5 words (DT7890 to
DT8191)
Available
L60