Related Manuals for Advantech ACP-5260
Summary of Contents for Advantech ACP-5260
- Page 1 User Manual ACP-5260 5U Rackmount Industrial Computer Chassis with SCSI Ultra320 Mobile HDD Trays...
- Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd.
-
Page 3: Safety Instructions
PRIATE SAFETY STANDARDS INCLUDING IEC 60825. CLASS I LASER PRODUCT KLASS I LASER PRODUKT This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1). this device may not cause harmful interference, and ACP-5260 User Manual... - Page 4 Advantech has come to be known. Your satisfaction is our primary concern. Here is a guide to Advantech’s cus- tomer services.
- Page 5 If an Advantech product is defective, it will be repaired or replaced at no charge dur- ing the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
- Page 6 ACP-5260 User Manual...
-
Page 7: Table Of Contents
Table 4.1: CN1, Auxiliary External Power Connector, Standard Mini 4-Pin Power Connector........25 Table 4.2: CN4, Thermal Sensor(LM75) Connector....25 Table 4.3: CN13, Voltage Detection Input Connector ....25 Table 4.4: CN16, Power Good Input Connector......25 ACP-5260 User Manual... - Page 8 Table A.1: Parts List ..............39 Appendix B Backplane & Motherboard Options. 41 Backplane Options.................. 42 Table B.1: PICMG 1.3 Backplane Options ........ 42 Table B.2: PICMG 1.0 Backplane Options ........ 42 Motherboard Options ................43 Table B.3: Motherboard Options..........43 ACP-5260 User Manual viii...
-
Page 9: Chapter 1 General Information
Chapter General Information This chapter provides general information about the ACP-5260. Sections include: ! Introduction ! Specifications ! Power supply options ! Environment specifications ! Dimension diagram... -
Page 10: Introduction
Introduction ACP-5260 is a 5U rackmount industrial computer chassis for high-performance and high-capacity computing platforms. It meets a variety of application needs for filing, printing, e-mail and web serving. This powerful computing server includes full disk array storage for minimizing system downtime, especially in mission-critical computer telephony applications, industrial automation, and factory management. -
Page 11: Power Supply Options
-20 to 60°C (-4 to 140°F) 10 to 85% @ 40°C, non-con- 10 to 95% @ 40°C, non-con- Humidity densing densing Vibration 1G rms 10G with 11 ms duration, half Shock 30 G sine wave Safety CE compliant ACP-5260 User Manual... -
Page 12: Dimension Diagram
Dimension Diagram 216,3 [8,52] 426,0 [16,77] 86,0 [3,39] 471,0 [18,54] 482,0 [18,98] unit: mm [inch] Figure 1.1 Dimension diagram ACP-5260 User Manual... -
Page 13: Chapter 2 System Setup
Chapter System Setup This chapter introduces the instal- lation process. Sections include: ! Chassis front and rear section ! Installing the backplane ! Installing the CPU card or add- on card ! Installing disk drives ! Attaching the ears and handles... -
Page 14: Chassis Front And Rear Section
Chassis Front and Rear Sections The ACP-5260 is composed of two sections, the front section and the rear section. Each of them has its own top cover. 2.1.1 The Front Section Includes: A SCSI disk drive housing with six mobile HDD trays on the front left. -
Page 15: The Rear Panel Includes
Hold-down clamp and blower brackets Removing the Chassis Covers There are dual top covers for ACP-5260, top front cover and top rear cover. Both are fixed to the chassis with four screws, two on each side. Please refer to Figure 2.2 &... -
Page 16: Installing The Backplane
Installing the Backplane ACP-5260 supports backplanes of up to 20 slots. To install the backplane, please refer to Figure 2.4 and proceed as follows: Remove the top rear chassis cover, and then dismantle the hold-down clamp and the blower units by removing the four screws. -
Page 17: Installing Cpu Card & Add-On Cards
Installing CPU Card & Add-on Cards ACP-5260 supports up to 20 add-on cards. To install a CPU card or add-on card, please proceed as follows: Select a vacant PICMG slot for the full-length CPU card, or a PCI/ISA slot for other add-on cards. -
Page 18: Hold-Down Clamp
The cushions offer these cards the protection against shock and vibration. Put the hold-down clamp back into its original position. Secure the hold-down clamp to the chassis with the four screws. Figure 2.6: Installing hold-down clamp ACP-5260 User Manual... -
Page 19: Installing Disk Drives
Connect the suitable cables from the CPU card to the 3.5” HDD, FDD or the optical disk drive. Then plug the 4-pin power connector into each disk drive. Put the disk drive housing back in the correct position and fasten it with the screws. Figure 2.7: Installing IDE disk drives ACP-5260 User Manual... -
Page 20: Attaching The Ears And Handles
There is a pair each of ears and handles in the accessory box. If you need to install the chassis in a rack, please fasten the ears and handles to the front-right and front- left edges with the screws provided. ACP-5260 User Manual... -
Page 21: Chapter 3 Operation
Chapter Operation This chapter introduces the sys- tem operation information. Sections include: ! The front panel ! The rear panel ! Replacing the cooling fans ! Replacing the filters ! Replacing the power supply... -
Page 22: The Front Panel
The following table describes the LED indicators for System Status. Table 3.1: LED Indicators for System Status Description Green System Power Normal Abnormal Hard Disk Drive Activ- Data Access No light Temperature in the TEMP Normal Abnormal Chassis Cooling Fan Normal Abnormal ACP-5260 User Manual... -
Page 23: Led Indicators For Power Voltage Status
When an LED fails to light up, it means there is a problem with one of the voltage sig- nals. Please check that the power supply connector is properly attached to the back- plane. If the problem persists, consult with an experienced technician. ACP-5260 User Manual... -
Page 24: The Rear Panel
For M/B version, it includes the M/B rear plate with 7-slot I/O brackets and the ATX M/B I/O cover (Figure 3.3). The M/B version is especially customized by customers' request. Figure 3.2: Rear panel of backplane version Figure 3.3: Rear panel of motherboard version ACP-5260 User Manual... -
Page 25: Replacing The Cooling Fan
You can adjust its position along with the length of the guide rail bracket. Plug the blower power connector to the alarm board and fix the wire into the tie mount. Replace the top rear chassis cover and fasten it to the chassis. ACP-5260 User Manual... -
Page 26: Figure 3.6 Both Sides Of The Blower Unit
Figure 3.5: Removing the blower unit Figure 3.6 Both sides of the blower unit ACP-5260 User Manual... -
Page 27: Replacing The Fan Behind The Scsi Backplane
Plug the fan wire into the fan connector on the SCSI backplane. Replace the two high-speed cooling fans and fasten them. Replace the top front chassis cover. Figure 3.7: Remove the two high-speed cooling fans Figure 3.8: Lift the tab on top of the fan unit ACP-5260 User Manual... -
Page 28: Replacing The Filter
3.4.1 Replacing the Door Filters Open the front door. Loosen the two screws located on each filter cover. Replace the filter with a new one. Fasten the filter covers. Figure 3.10: Replacing the front door filter ACP-5260 User Manual... -
Page 29: Replacing The Side Filter
Replace the top front cover and then fasten it. Figure 3.11: Replacing the side filter Replacing the Power Supply ACP-5260 supports various power supply models. To replace the power supply mod- ule, please proceed as follows. Turn off the failed power supply module. - Page 30 Figure 3.13: Replacing the module of 570W / 810W redundant power Note! When you plug the two power cords into the socket, please make sure they are oriented in the same direction. (See Figure 3.14) Figure 3.14: Orientation of power cord plugs ACP-5260 User Manual...
-
Page 31: Chapter 4 Alarm Board
Chapter Alarm Board This chapter introduces the alarm board and thermal sensor specifi- cations. Sections include: ! Alarm Board Layout ! Alarm Board Specifications ! Thermal Sensor ! Sensor I.D. Number Setting... -
Page 32: Alarm Board Layout
One power good input One alarm reset input One voltage signal connector (connect from backplane, includes ±12 V, ±5 V, +3.3 V) One Hard Disk LED connector (connect from CPU card) Output Signals: One LED board connector One Buzzer output ACP-5260 User Manual... -
Page 33: Connectors, Jumper, And Pin Definition
Table 4.9: J1, External Buzzer Pin 1 Buzzer Pin 2 +5 V Table 4.10: SW1, Fan Number Select Switch Pin 1 Pin 5 Pin 2 FAN_SEL1 Pin 6 FAN_SEL3 Pin 3 Pin 7 Pin 4 FAN_SEL2 Pin 8 RESET ACP-5260 User Manual... -
Page 34: Switch Settings
FAN2. If the two fans are connected to other fan connectors, out of sequence, such as FAN1 and FAN3 or FAN2 and FAN3 or FAN3 and FAN4, instead of FAN1 and FAN2, then the alarm will not function cor- rectly. ACP-5260 User Manual... -
Page 35: Thermal Sensor
+5 V Pin 3 T_SDAT Pin 2 T_SCLK Pin 4 Table 4.13: SW1, Thermal Sensor I.D. no. Setting Sensor I.D. No. SW 1 -1 SW 1 - 2 SW 1 - 3 SW 1 - 4 1 (default) ACP-5260 User Manual... - Page 36 ACP-5260 User Manual...
-
Page 37: Scsi Storage And Raid
Chapter SCSI Storage and RAID This chapter introduces the SCSI storage structures. Sections include: ! 6-slot SCSI SCA backplane ! SCSI disk drive housing ! Installing SCSI disk drives... -
Page 38: 6-Slot Scsi Sca Backplane
80-pin SCSI connectors, so users can install up to six 80-pin SCSI HDDs. Please see the relevant details below. 6-slot SCSI SCA Backplane 5.1.1 SCSI Backplane Layout Figure 5.1: Front side layout of the SCSI backplane Figure 5.2: Back side layout of the SCSI backplane ACP-5260 User Manual... -
Page 39: Connectors And Jumpers
After all the relevant wires/cables, fans, and mobile trays have been disconnected, release the four screws with the rubber cushions on the SCSI disk drive housing, then lift it up so that you can take out the SCSI disk drive housing. Figure 5.3: SCSI disk drive housing ACP-5260 User Manual... -
Page 40: Wires & Cables For Scsi Storage
Return the mobile tray with SCSI HDD to the disk drive housing and push it in by the handle until it is locked into the original position. Push down the latch to lock the tray into place. ACP-5260 User Manual... - Page 41 Figure 5.5: Pushing up the latch Figure 5.6: Removing the mobile tray Figure 5.7: Installing a SCSI SCA 80-pin disk drive ACP-5260 User Manual...
-
Page 42: Installing The Gem318 Driver
The GEM318 can work well without a driver, but in order for a Windows 2000 OS to recognize it, you must install the driver. Please follow the steps below to download the GEM318 driver from the Advantech website. Connect to Advantech’s eService website: http://eservice.advantech.com.tw. -
Page 43: Saf-Te
(LED, audible alarm, LCD, etc.), hot- swap Ultra320 SCSI HDDs, and monitoring of enclosure components, such as disk drives, power supplies, thermal sensors, fans, etc. For ACP-5260, the GEM318 chipset checks the disk status only, others items such as fans, temperature, power supply and voltage are monitored by an alarm board. - Page 44 ACP-5260 User Manual...
-
Page 45: Appendix A Exploded Diagram And Parts List
Appendix Exploded Diagram and Parts List... -
Page 46: Exploded Diagram And Parts List
Exploded Diagram and Parts List Figure A.1 Exploded diagram ACP-5260 User Manual... -
Page 47: Table A.1: Parts List
Sensor Board System Reset Button Adapter Bracket Alarm Reset Button Mounting Plate ATX Power ON Switch Transparent Sheet Filter Cover Key Set Door Filter (155x100 mm) Hold Down Clamp Door Hinge (Left) Fan Bracket (120 mm) Fan Blower ACP-5260 User Manual... - Page 48 ACP-5260 User Manual...
-
Page 49: Appendix B Backplane & Motherboard Options
Appendix Backplane & Motherboard Options... -
Page 50: Backplane Options
Backplane Options ACP-5260 supports a variety of PICMG 1.3 / 1.0 backplanes. Users can contact a local sales representative for detailed specifications and information. Table B.1: PICMG 1.3 Backplane Options Slots per Segment Model Name Segment SHB* PCIe x 16... -
Page 51: Motherboard Options
Motherboard Options ACP-5260 supports a variety of Advantech ATX motherboards as listed below. You can contact a local sales representative for detailed information. Table B.3: Motherboard Options Model Name PCI/ISA SATA AIMB-742 4 (32-bit) 1 (8X) 2 (PCI-X 64-bit) AIMB-744... - Page 52 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2009...