IBM 7378 Problem Determination And Service Manual page 7

Removing and replacing Tier 2 CRUs . . . . . . . . . . . . . . . . 220
Removing the operator information panel assembly . . . . . . . . . . 220
Installing the operator information panel assembly . . . . . . . . . . 222
Removing a voltage regulator module . . . . . . . . . . . . . . . 223
Installing a voltage regulator module . . . . . . . . . . . . . . . 224
Installing memory . . . . . . . . . . . . . . . . . . . . . . 226
Removing a USB embedded hypervisor flash device
Installing a USB embedded hypervisor flash device . . . . . . . . . . 236
Removing an optional ServeRAID adapter advanced feature key . . . . . 236
Installing an optional ServeRAID adapter advanced feature key . . . . . 238
Removing the bezel
Installing the bezel . . . . . . . . . . . . . . . . . . . . . . 242
Removing the fan cage assembly
Installing the fan cage assembly . . . . . . . . . . . . . . . . . 244
Removing an optional tape drive . . . . . . . . . . . . . . . . . 246
Installing an optional tape drive . . . . . . . . . . . . . . . . . 248
Removing the USB cable and light path diagnostics assembly . . . . . . 250
Installing the USB cable and light path diagnostics assembly . . . . . . 252
Removing a 2.5-inch disk drive backplane . . . . . . . . . . . . . 254
Installing a 2.5-inch disk drive backplane . . . . . . . . . . . . . . 256
Removing the 3.5-inch hot-swap hard disk drive backplane . . . . . . . 257
Installing the 3.5-inch hard disk drive backplane . . . . . . . . . . . 259
Removing the simple-swap backplate . . . . . . . . . . . . . . . 261
Installing the simple-swap backplate
Removing the 2.5-inch disk drive cage. . . . . . . . . . . . . . . 265
Installing the 2.5-inch disk drive cage . . . . . . . . . . . . . . . 267
Removing and replacing FRUs
Removing the upper 3.5-inch disk drive cage . . . . . . . . . . . . 268
Installing the upper 3.5-inch disk drive cage . . . . . . . . . . . . . 270
Turning the stabilizing feet . . . . . . . . . . . . . . . . . . . 272
Removing a hot-swap power supply. . . . . . . . . . . . . . . . 273
Installing a hot-swap power supply . . . . . . . . . . . . . . . . 274
Removing the power-supply cage
Installing the power-supply cage . . . . . . . . . . . . . . . . . 278
Removing an extender card. . . . . . . . . . . . . . . . . . . 281
Installing an extender card . . . . . . . . . . . . . . . . . . . 283
Removing a microprocessor and heat sink . . . . . . . . . . . . . 284
Installing a microprocessor and heat sink . . . . . . . . . . . . . . 286
Removing a heat-sink retention module . . . . . . . . . . . . . . 292
Installing a heat-sink retention module . . . . . . . . . . . . . . . 293
Removing a microprocessor retention module . . . . . . . . . . . . 294
Installing a microprocessor retention module
Removing the system board
Installing the system board . . . . . . . . . . . . . . . . . . . 298
Chapter 6. Configuration information and instructions
Updating the firmware . . . . . . . . . . . . . . . . . . . . . . 302
Using the Setup utility . . . . . . . . . . . . . . . . . . . . . . 303
Starting the Setup utility . . . . . . . . . . . . . . . . . . . . 303
Setup utility menu choices . . . . . . . . . . . . . . . . . . . 303
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . 306
Using the Boot Selection Menu program . . . . . . . . . . . . . . . 308
Starting the backup server firmware . . . . . . . . . . . . . . . . . 308
Using the ServerGuide Setup and Installation CD. . . . . . . . . . . . 308
ServerGuide features . . . . . . . . . . . . . . . . . . . . . 309
Setup and configuration overview
. . . . . . . . . . . . . . . . . . . . . 239
. . . . . . . . . . . . . . . . 243
. . . . . . . . . . . . . . . 263
. . . . . . . . . . . . . . . . . . 268
. . . . . . . . . . . . . . . . 276
. . . . . . . . . . . . . . . . . . 296
. . . . . . . . . . . . . . . . 309
. . . . . . . . . 234
. . . . . . . . . . . . 295
. . . . . . . . 301
v
Contents