Anti-Reset Windup; Setting The Anti-Reset Windup; Normal/Reverse Setting; Setting The Normal/Reverse Setting - FujiFilm PXG4 Operation Manuals

to

Anti-reset Windup

Sets the anti-reset windup. Up to seven types of anti-
reset windup (palettes 1 to 7) can be recorded. Recorded
anti-rest windup can be recalled from selected PID
number ("P P P P L L L L n n n n 1 1 1 1 ") in the operation menu.
• Range: 0.0% to 100.0%
Refer to
See "Anti-reset Windup" (p. 36) for more information on the anti-
reset windup.

Setting the Anti-reset Windup

The following steps explain how to set the anti-reset windup
by using 200°C as an example.
Chapter
Press and hold the
5
1
mode channel menu ("o o o o P P P P E E E E C C C C h h h h 1 1 1 1 ") then use the
keys to display PLT ("P P P P L L L L T T T T C C C C h h h h 3 3 3 3 ").
Refer to
See p. 46 in this chapter for information on how to display
the channel menu.
Press and hold the
2
parameter ("S S S S v v v v 1 1 1 1 "), then use the
display Ar1 ("A A A A r r r r 1 1 1 1 ").
Press the
3
display "200.0" when the bottom part of the
display begins to blink.
Anti-reset windup is set to 200.0°C.
Press the
4
Press the
5
PV/SV display.
key to display the setup
key to display the SV
key, then use the
key to confirm the setting.
key to return to the operation mode
to

Normal/Reverse Setting

The following sets the normal/reverse setting. Up to
seven types of normal/reverse settings (palettes 1 - 7)
can be recorded. Recorded normal/reverse settings can
be recalled from selected PID number ("P P P P L L L L n n n n 1 1 1 1 ") in the
operation menu.
Range
rv--
no--
rvno
norv
rvrv
nono
Refer to
See "Normal/Reverse Settings" (p. 37) for more information on
normal/reverse settings,

Setting the Normal/Reverse Setting

The following steps explain how to set normal/reverse settings
by using heat (reverse) / cool (normal) as an example.
Press and hold the
1
mode channel menu ("o o o o P P P P E E E E C C C C h h h h 1 1 1 1 ") then use the
keys to display PLT ("P P P P L L L L T T T T C C C C h h h h 3 3 3 3 ").
keys to
Refer to
Press and hold the
2
parameter ("S S S S v v v v 1 1 1 1 "), then use the
keys to
display rEv1 ("r r r r E E E E v v v v 1 1 1 1 ").
Press the
3
select "rvno" when the bottom part of the display
begins to blink.
The normal/reverse setting is now set to heat
(reverse) / cool (normal).
Press the
4
Press the
5
PV/SV display.
Point
– 50 –
Control Operation
(heat (reverse) / cool (none))
(heat (normal) / cool (none))
(heat (reverse) / cool (normal))
(heat (normal) / cool (reverse))
(heat (reverse) / cool (reverse))
(heat (normal) / cool (normal))
key to display the setup
See p. 46 in this chapter for information on how to display
the channel menu.
key to display the SV
key, then use the
key to confirm the setting.
key to return to the operation mode
For safety reasons, make sure to turn off power to the
system when switching the normal/reverse operations
while using the PID selection function. (Do not switch
between normal and reverse operation while controlling.)
keys to
keys to