Fuji Electric FRN0001C2S-2A FRN0002C2S-2A FRN0004C2S-2A FRN0006C2S-2A FRN0010C2S-2A FRN0012C2S-2A FRN0020C2S-2A FRN0025C2S-2A FRN0033C2S-2A FR Instruction Manual page 112

H codes: High Performance Functions
Code Name
H03 Data Initialization
H04 Auto-reset (Times) 0 (Disable), 1 to 10
H05 (Reset interval)
H06 Cooling Fan ON/OFF
Control
H07 Acceleration/
Deceleration Pattern
H08 Rotational Direction
Limitation
H11 Deceleration Mode
H12 Instantaneous
Overcurrent Limiting
(Mode selection)
H13 Restart Mode after
Momentary Power
Failure (Restart time)
H14 (Frequency fall rate)
H15 (Continuous running
level) *1
H26 Thermistor for Motor
(Mode selection)
H27 (Level)
H30 Communications Link
Function
(Mode selection)
H42 Capacitance of DC Link
Bus Capacitor
H43 Cumulative Run Time of
Cooling Fan
H44 Startup Counter of Motor
1
H45 Mock Alarm
H47 Initial Capacitance of DC
Link Bus Capacitor
H48 Cumulative Run Time of
Capacitors on Printed
Circuit Boards
*1 Available in the ROM version 0500 or later.
*5 In the ROM version 0800 or later, the factory setting is changed from 0.16 to 1.6.
(Note 1) For the three-phase / single-phase 200 V and single-phase 100 V class series
(Note 2) For the three-phase 400 V class series
Data setting range
0: Disable initialization
1: Initialize all function code data to the
factory defaults
2: Initialize motor 1 parameters
3: Initialize motor 2 parameters
0.5 to 20.0
0: Disable (Cooling fan always ON)
1: Enable (ON/OFF control effective)
0: Linear
1: S-curve (Weak)
2: S-curve (Strong)
3: Curvilinear
0: Disable
1: Enable (Reverse rotation inhibited）
2: Enable (Forward rotation inhibited）
0: Normal deceleration
1: Coast-to-stop
0: Disable
1: Enable
0.1 to 10.0
0.00 (Deceleration time selected)
0.01 to 100.00
999 (Depends upon current limiter)
200 to 300 (Note 1)
400 to 600 (Note 2)
0: Disable
1: Enable (With PTC, the inverter
0h4
immediately trips with
2 Enable (With PTC, the inverter issues
output signal THM and continues to run.
0.00 to 5.00
Frequency command Run command
0: F01/C30 F02
1: RS-485 F02
2: F01/C30 RS-485
3: RS-485 RS-485
Indication for replacement of DC link bus
capacitor (0000 to FFFF in hex.)
Indication for replacement of cooling fan
(0 to 9999, in units of 10 hours)
Indication of cumulative startup count
(0000 to FFFF in hex.)
0: Disable
1: Enable (Once a mock alarm occurs, the
data automatically returns to 0.)
Indication for replacement of DC link bus
capacitor (0000 to FFFF in hex.)
Indication for replacement of capacitors on
printed circuit boards
(0 to 9999, in units of 10 hours)
5-13
Incre-
Unit
ment
– –
1
times
0.1 s
– –
– –
– –
– –
– –
0.1 s
0.01 Hz/s
1 V
– –
displayed.)
0.01 V
– –
–
1
1 10h
– –
– –
–
1
1 10h
Change Refer
Data Default
when to
copying setting
running page:
N N 0 5-64
Y Y 0 5-70
Y Y 5.0
Y Y 0 5-71
Y Y 0
N Y 0
Y Y 0 5-72
Y Y 1 5-73
Y Y1 5-31
See
Y2
Table A.
Y Y 999
Y Y2 235
470
Y Y 0
Y Y 1.6 *5
Y Y 0
–
Y N
–
Y N
–
Y N
Y N 0 5-74
–
Y N
–
Y N
–
–
–