Intended Use - Truma Mover S User Manual

Installation instructions
Read the installation instructions prior to starting work and
follow them carefully!
Please ensure that no metal chips or other contaminants get
into the controller during installation.

Intended use

The Mover SE R is designed for use on single-axle caravans
with a gross weight of up to 2000 kg,
and the Mover TE R is designed for use on dual-axle cara-
vans with a gross weight of up to 2250 kg.
The Mover SE R / TE R weighs approx. 33 kg.
Check the towing load of your vehicle and the gross weight of
your caravan in order to establish whether they are designed
for the additional weight.
Approval
The Truma Mover SE R / TE R has design approval, and a
general operating permit (ABE) has been issued for Germany.
Acceptance by a vehicle expert is not required (except when
installing the flat frame kit). The ABE must be kept in the
vehicle.
The Mover SE R / TE R complies with the vehicle engine inter-
ference suppression directive 72/245/EEC with supplements
2004/104/EC, 2005/83/EC and 2006/28/EC and bears type
approval number: e1 03 4473
The Mover SE R / TE R complies with EMC directive 89/336/EEC
(2004/108/EC) and low voltage directive 73/23/EEC.
The remote hand set and the receiver comply with the
requirements of the R&TTE directive 1995/5/EC.
The Mover SE R / TE R satisfies the Machinery Directive
2006/42/EC.
The technical and administrative regulations of the country in
which the vehicle is initially registered must be complied with
when the Mover is being installed.
Any modifications to the unit or the use of spare parts and
accessories that are important to the operation of the system
that are not original Truma parts and failure to follow the in-
stallation and operating instructions will cancel the warranty
and indemnify Truma from any liability claims. In addition to
this, the operational approval for the device will be cancelled.
Tools and facilities required
To install the unit you will need
13 mm, 17 mm socket wrench, ring spanner or open-jawed
spanner
Torque wrench (5 – 40 Nm)
Cable cutter / Crimping tool
Power drill / screwdrivers / 25 mm hole cutter
Portable 2 tonne trolley jack and axle stands to suit
Appropriate lighting.
Minimum installation dimensions
The equipment can only be fitted to caravans / trailers within
the following dimensions.
Caravan Floor
opt. 185
min. 30
max. 48
min. 60
max. 2400
all dimensions in mm
* with fully loaded vehicle
A distinction is made between L-profiled and U-profiled
chassis as shown in the illustration.
Caravan Floor
L-Profile
Measuring the chassis height
Frame height (Y) measured at distance of 106 mm (X) from
the outer edge of the tyre at height of hub / middle of tyre.
Determining the installation type
1. Standard installation
Standard installation is used with a U-profile or L-profile chas-
sis and a frame height (Y) of approx. 185 mm. No special
accessories are required.
2. Installation with chassis with U-profile or L-profile
and frame height of between 140 and 185 mm
With a chassis with a frame height (Y) of 140 mm to 185 mm,
1, 2 or 3 spacer plate sets and the screw set are needed to
compensate for the height.
3. Installation with chassis with U-profiles or L-profiles
with frame height of less than 140 mm
With a chassis with a frame height (Y) of less than 140 mm a
low chassis kit must be fitted to compensate for the height.
In Germany, the low chassis kit installation must
be accepted by a vehicle expert.
4. The AL-KO Vario III / AV installation kit must be used
with the AL-KO Vario III / AV chassis with a frame thickness of
less than 2.8 mm.
5. Installation with Eriba Touring chassis
The Eriba Touring mounting set is needed for the Eriba Touring
chassis.
max. 1860
U-Profile
17