JUKI SC-510 Engineer's Manual page 27

Input function list
Function
Abbreviation
code
0 nop No function
1 HS Needle up / down compensating
stitching
2 bHS Back compensating stitching
3 Ebt Function of canceling once reverse
feed stitching at the end of sewing
4 TSW Thread trimming function
5 FL Presser foot lifting function
6 oHS One stitch compensating stitching
7 SEbt Function of cancel of reverse feed
stitching at start/end
8 PnFL Presser lifting function when pedal
is neutral
9 Ed Material edge sensor input
10 LinH Function of prohibiting depressing
front part of pedal
11 TinH Function of prohibiting thread
trimming output
12 LSSW Low speed command input
13 HSSW High speed command input
14 USW Needle lifting function
15 rSW Reverse revolution to lift needle
function
16 SFSW Safety switch input
17 MES Thread trimmer knife sensor input
18 AUbT Cancel of automatic reverse feed
stitching/input of addition switch
19 vErT Alternate vertical amount change
panel switch input
20 vSW Alternate vertical amount change
knee switch input
Output function list
Function
Abbreviation
code
nop
0 No function
1 TrM Thread trimming output
2 WP Thread wiper output
3 TL Thread release output
4 FL Presser lifter output
bT Reverse feed stitching output
5
6 Ebt EBT cancel monitor output
7 SEbt Reverse feed stitching at start/
end cancel monitor output
Automatic reverse feed stitching
8 AUbt
cancel/addition monitor output
9 vErT Alternate vertical amount change
(monitor) output
10 SSTA Sewing machine stop state output
* Magnet output does not work when they are used as optional.
(Caution) Note that the voltage used in output function should not exceed the voltage set with W1 and W2.
Function item
Every time the switch is pressed, normal feed stitching by half
stitch is performed. (Same operation as that of up / down
compensating stitching switch on the panel.)
switch is held pressing. (It is effective only when constant
dimension sewing pattern is selected with the CP-160.)
By depressing the back part of the pedal after pressing the
switch, operation of reverse feed stitching is canceled once.
This function is actuated as the thread trimming switch.
This function is actuated as the foot lifter switch.
Every time the switch is pressed, one stitch stitching operation
is executed.
By operating the optional switch, ineffective/effective can be
alternately changed over.
Every time the switch is pressed, the function whether
automatically lifting the presser foot when the pedal is neutral
or not can be selected.
This function works as the input signal of material edge sensor.
Rotation by pedal is prohibited.
Output of thread trimming is prohibited.
This function works as low speed switch for standing sewing machine.
This function works as high speed switch for standing sewing machine.
UP stop motion is performed when switch is pressed during
DOWN stop.
Brake stop motion by reverse revolution is performed at specified
angle when switch is pressed during DOWN stop
Rotation is prohibited.
This function works as input signal of thread trimmer knife sensor.
Every time the switch is pressed, cancel or addition of reverse
feed stitching at start or end is performed.
Every time the switch is pressed, alternate vertical amount
change output is inversed.
Alternate vertical amount change output is performed as long
as the switch is pressed.
Function item
(Standard setting)
Output of thread trimming signal *
Output of thread wiper signal *
Output of thread release signal *
Output of presser lifting signal *
Output of reverse feed stitching signal *
State of one time cancel of reverse feed stitching at end function
is output.
State of cancel of reverse feed stitching at start/end is output.
State of cancel or addition of automatic reverse feed stitching is
output.
Output of alternate vertical amount change signal
Sewing machine stop state is output.
−
Remarks
(Standard setting)
Reverse feed stitching is performed at low speed while the
Remarks
*
22
−