JUKI SC-510 Engineer's Manual page 21

(Start level ; U : User's mode, S : Service mode)
No.
Item
Reversing Stop brake start angle of reverse revolution to lift needle input (Rsw)
19 brake start is set.
angle 0 : UP detection missed
Alternate Output start delay time of alternate presser output signal of LH series
20 vertical amount is set.
output delay
time
Function of Function of lifting presser foot when the pedal is in neutral position.
21 neutral presser
0 : Function of neutral automatic presser lifting is not operative.
lifting
1 : Selection of function of neutral presser lifting.
Function of Function of needle up/down compensating switch on the operation
changeover of panel can be changed.
compensating
0 : Needle up/down compensation
22
switch on the
1 : One stitch compensation
operation
panel function
Function of
Motion of switch for presser of pedal for standing work is set.
input of
0 : Normal presser motion (FLsw)
presser for
1 : Alternate motion of input of normal presser
standing work
2 : Alternate vertical switch (DLsw) function
24
3 : Alternate motion of alternate vertical switch (DLsw)
4 : Level input wrapper control and presser synchronizing control
5 : Level input wrapper control
6 : Alternate input wrapper control
This function sets the thread trimming motion after DOWN position
Thread
has been off by turning handwheel by hand.
trimming
25
motion
0 : Thread trimming after turning handwheel by hand is permitted.
condition
1 : Thread trimming after turning handwheel by hand is prohibited.
Suction time of
This function sets the suction motion time of the back-tack solenoid.
the first start of
50 ms to 500 ms
29 the back
solenoid
Function of
Function of reverse feed stitching on the way
reverse feed
0 : Function of reverse stitching on the way is not operative.
30
stitching on the
1 : Function of reverse feed stitching on the way is operative.
way
Number of
Number of stitches of reverse feed stitching on the way.
stitches of
reverse feed
31
stitching on the
way
Effective
Effective condition of reverse feed stitching on the way
condition of
0 : Function is not operative when the sewing machine stops.
reverse feed
1 : Function is operative when the sewing machine stops.
stitching on the
32
way when the
sewing
machine is
stopping.
Thread trimming function by reverse feed stitching on the way
Thread
trimming
0 : Automatic thread trimming function after completion of reverse
33 function by
reverse feed
1 : Automatic thread trimming after completion of reverse feed
stitching on the
way
Number of
Lowest speed by pedal
35
* rotation at a
low speed
Number of
20 Number of rotation at the time of thread trimming is set.
36
rotation of
(This setting is prior even when number of rotation is lower than the
thread
lowest speed by pedal of No. 35.)
trimming
Sewing speed at the start of sewing (soft-start)(The max. value
Number of
depends on the number of rotation of the sewing machine head.)
37
One-shot
One-shot speed (The max. value depends on the number of rotation
38
speed
of the sewing machine head.)
Pedal stroke at
Position where the sewing machine starts rotating from pedal neutral
39
the start of
position (Pedal stroke)
rotation
Low speed
Position where the sewing machine starts accelerating from pedal
40
section of
neutral position (Pedal stroke)
pedal
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the time
of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
(Descriptions of setting in this list are the standard values at the time of delivery.)
However, contents of function setting are subject to change for improvement of function and performance without notice.
Description
feed stitching on the way is not operative.
stitching on the way is performed.
Start
level
S
S
U
U
U
U
U 50 to 500
U
U
(Stitches)
U
U
150 to 250
U
100 to 250
S
100 to MAX
U
150 to MAX
U
10 to 50
U
(0.1 mm)
10 to 100
U
(0.1 mm)
16
− −
Setting Indication of
range
function setting
0 to 359
1 9
(degree) 3
2 0
0 to 500
(ms)
0/1
2 1
0/1
2 2
2 4
0 to 6
0/1 2 5
2 9
2
(ms)
0/1
3 0
0 to 19
3 1
0/1
3 2
0/1
3 3
3 5
2
(rpm)
3 6
1
5 (rpm)
3 7
8
(rpm)
3 8 2 5
(rpm)
3 9
4 0
Ref.
page
24
5 9
1 0
24
24
0
0
25
25
2
25
1
25
5 0
26
0
4 26
0
26
26
0
0 0
27
0 0
20
0 0
0 0
27
3 0
6 0