JUKI SC-510 Engineer's Manual page 22

(Start level ; U : User's mode, S : Service mode)
No.
Item
Starting
Position where the cloth presser starts lifting from pedal neutral
position of
41
position (Pedal stroke)
lifting presser
foot by pedal
Starting
Starting position of lowering presser foot
42 position of
Stroke from the neutral position
*
lowering
presser foot
Pedal stroke 2
Position 2 where the thread trimming starts from pedal neutral position
43
*
for starting
(When the function of lifting presser foot by pedal is provided.) (Pedal
thread trimming
stroke)
Pedal stroke for
Position where the sewing machin reaches its highest sewing speed
reaching the
from pedal neutral position (Pedal stroke)
44
*
maximum
number of
rotation
Compensation of
Compensation value of the pedal sensor
45
*
neutral point of
the pedal
Auto-lifter
Auto-lifter selection
46
*
selecting function
0 : Solenoid drive system
1 : Pneumatic drive system
Holding time of
Limitation time of waiting for lifting solenoid type auto-lifter device
47
lifting auto-lifter
Pedal stroke 1
Position where thread trimming starts from pedal neutral position
48
*
for starting
(Standard pedal) (Pedal stroke)
thread trimming
Pedal presser
PFL type of pedal type is set
50
lifting function
0 : OFF
1 : ON
Compensation of
Compensation of starting the solenoid for reverse feed stitching when
solenoid-on
reverse feed stitching at the start of sewing is performed.
timing of reverse
51 feed stitching at
the start of
sewing
Compensation of Compensation of releasing the solenoid for reverse feed stitching
solenoid-off when reverse feed stitching at the start of sewing is performed.
52
timing of reverse
feed stitching at
the start of
sewing
Compensation of Compensation of releasing the solenoid for reverse feed stitching
solenoid-off when reverse feed stitching at the end of sewing is performed.
53
timing of reverse
feed stitching at
the end of
sewing
Motor pulley Effective diameter of pulley to be used for motor is set.
54
effective
diameter
Foot lift after Function of lifting presser foot at the time of (after) thread trimming
thread trimming 0 : Not provided with the function of lifting presser foot after thread
55
1 : Provided with the function of lifting presser foot automatically
Bobbin thread Function of reverse revolution to lift the needle at the time of (after)
remaining thread trimming
56 amount detection 0 : Not provided with the function of reverse revolution to lift the
function
1 : Provided with the function of reverse revolution to lift the needle
Function of Function of bobbin thread remaining amount detection device is set.
bobbin thread 0 : Invalid
remaining 1 to : Valid function is selected.
57
amount
detection
Function of holding predetermined upper/lower position of the needle
Function of
bar
holding
0 : Not provided with the function of holding predetermined upper/
predetermined
upper/lower
58
1 : Provided with the function of holding predetermined upper/
position of the
needle bar
2 : Provided with the function of holding predetermined upper/
3 : Provided with the function of holding predetermined upper/
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the time
of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
(Descriptions of setting in this list are the standard values at the time of delivery.)
However, contents of function setting are subject to change for improvement of function and performance without notice.
Description
trimming
after thread trimming
needle after thread trimming
after thread trimming
lower position of the needle bar
lower position of the needle bar (holding force is weak.)
lower position of the needle bar (holding force is medium.)
lower position of the needle bar (holding force is strong.)
Start
level
–60 to –10
U
U
–60 to –10
U
10 to 150
U
U –15 to 15
S
10 to 600
U
–60 to –10
U
S
–36 to 36
U
U
U
S
U
U
S
U
17
− −
Indication of
Setting
range
function setting
4 1
–
(0.1mm)
8 to 50
4 2
(0.1 mm)
4 3 –
(0.1 mm)
4 4
(0.1 mm)
4 5
4 6
0/1
4 7
(second)
4 8 -
(0.1 mm)
0/1
5 0
5 1
(10˚)
–36 to 36
5 2
(10˚)
5 3
–36 to 36
(10˚)
50 to 140
5 4
5 (mm)
5 5
0/1
0/1
5 6
5 7
0 to
0 to 3
5 8
Ref.
page
2 1
1 0
5 1
1 5 0
0
0 27
6 0 27
3 5
27
0
27
1 0
28
1 6
1 8
28
5 0 0 28
1
28
0 28
0
28
29
0