Integra DRX-7.1 Basic Manual page 52

> Specifications > Advanced Setup
Setting Item Default Value
Surround Right 0.0 dB
Surr Back Right 0.0 dB
Surr Back Left 0.0 dB
Surround Left 0.0 dB
Subwoofer 1 0.0 dB
Subwoofer 2 0.0 dB
■ 5. Dolby Enabled Speaker
Setting Item Default Value
Dolby Enabled 6' 0" / 1.80 m
Speaker to
Ceiling
16
> Listening Modes > Network Functions
Setting Details
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
• Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
• Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "−15.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "−15.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Setting Details
Set the distance between the Dolby Enabled
Speaker and the ceiling. Select between " 0' 0" 1/2
"/"0.01 m" to " 15' 0" "/"4.50 m" (1/2 / 0.01 m units).
• The unit of distance (feet / meters) shown is the
unit selected for use in "Distance".
Setting Item Default Value
AccuReflex Off
• This setting can be selected when "Configuration" - "Height 1 Speaker"/"Height 2 Speaker" is set to
"Dolby Speaker".
■ 6. Equalizer Settings
You can adjust the output volume of the range of each connected speaker. You can adjust
the volume of the different sound ranges for each of the speakers. You can set three
different equalizers in Preset 1 to 3. You can select up to five bands for the Subwoofer and
15 bands for all other speakers.
Setting Item Default Value
Front 0.0 dB
Center 0.0 dB
Height 1 0.0 dB
Height 2 0.0 dB
> Basic Manual
Troubleshooting | Supplementary Information, etc.
Setting Details
You can enhance the reflection effect of Dolby
Enabled Speakers from the ceiling.
"Off": When this function is not to be used
"On": When this function is to be used
Setting Details
After selecting the speaker frequency from
between "25 Hz" and "16 kHz" with the cursors
/ , adjust the volume of that frequency between
"−6.0 dB" and "＋6.0 dB" with / .
After selecting the speaker frequency from
between "25 Hz" and "16 kHz" with the cursors
/ , adjust the volume of that frequency between
"−6.0 dB" and "＋6.0 dB" with / .
After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/ , adjust the volume of that frequency between
"－6.0 dB" and "＋6.0 dB" with / .
• Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/ , adjust the volume of that frequency between
"－6.0 dB" and "＋6.0 dB" with / .
• Depending on the use of the ZONE speakers, it
may not be possible to select this setting.