DSC Power832 Installation Manual page 20

K E Y P
without entry delay") .
[06] - [ ]+[4] Door Chime On/Off
This function key provides the user a simple method for turning the Door Chime feature on and off (See
Section 3.4 [ ] Commands, [ ] [4] Door chime
[07] - [ ]+[6]...[4] System Test
This function key provides the user with a simple method for testing the system (See
Commands, [ ] [6] User
[08] - [ ]+[1] Bypass Mode
This function key provides the user with a simple method for entering the Bypass Mode. If a user code is
required it must be entered before bypassing can be performed (See
Zone Bypass") .
[09] - [ ]+[2] Trouble Display
This function key provides the user with a simple method for entering the Trouble Display Mode (See
Section 3.4 "[ ] Commands, [ ]+[2] Trouble display"
[10] - [ ]+[3] Alarm Memory
This function key provides the user with a simple method for entering the Alarm Memory Display Mode
(See Section 3.4 "[ ] Commands, [ ] [3] Alarm
[11] - [ ]+[5] Programming Access Codes
This function key provides the user with a simple method for programming user codes. After this key is
pressed a valid System Master or Partition Master will have to be entered before the panel will allow
programming to be performed (See
[12] - [ ]+[6] User Functions
This function key provides the user with a simple method for programming User Functions. After this key
is pressed a valid System Master or Partition Master must be entered before the panel will allow User
Functions to be performed (See
[13] - [ ]+[7]+[1] Utility Output
This function keys provides the user with a simple method for activating a PGM Output programmed as
Utility Output (See
entered (See Section 3.4 "[ ] Commands, [ ] [7] Utility output
[14] - [ ]+[7]+[2] Smoke Detector Reset
Same as described in Function Keys - Section 3.5.
[15] - General Voice Prompt Help
This feature can only be programmed if both the Escort5580 and the PC5928 Audio Matrix module are
being used.
When the function key is pressed, the intercoms will perform a Help page. The user must then press the
Page/Answer button on any intercom station to begin the help session with the Escort.
For more information, please refer to the PC5928 Installation Manual.
[16] - [ ]+[0] Quick Exit
Same as described in Function Keys - Section 3.5.
[17] - [ ]+[1] Reactivate Stay/Away Zones
This function key provides the user with a simple method for adding Stay/Away zones back into the system
at night-time (See
[18] Identified Voice Prompt Help
This feature can only be programmed if both the Escort5580 and the PC5928 Audio Matrix module are
being used.
When the function key is pressed, the Escort will begin a help session from the intercom station
programmed as closest to the keypad. In order for this option to function, you must program PC5928
Section [802], subsection [14] "Keypad Port Assignments." For more information, please refer to the
PC5928 Installation Manual.
Note: This function key cannot be programmed for PC55XX LED keypads with software version 1.0.
3.6 Global and Partition Keypad Operation
A global keypad will not display any information (the trouble LED will light if a trouble condition is present)
until a partition is selected. To select a partition the user must press and hold the [1] key for Partition 1 or
the [2] key for Partition 2 for two seconds. The keypad will then display the status of the selected partition
and allow normal operation.
A Partition keypad will display the status of the Partition for which it has been programmed. A user with
access to both partitions may temporarily assign the keypad to the other partition to gain access. To do
this the user must first press and hold the [#] key for two seconds. The keypad will go blank. The user
must then press and hold the [1] key for Partition 1 or the [2] key for Partition 2 for two seconds. The
keypad will then display the status of the selected partition and allow normal access.
A D
functions") .
Section 3.4 "[ ] Commands, [ ] [5] Programming Access
Section 3.4 "[ ] Commands, [ ] [6] User
Section 5.10 "PGM outputs") . After this key is pressed a valid user code must be
Section 3.4 "[ ] Commands, [ ] [1] Reactivate Stay/Away
C O M M
on/off") .
Section 3.4 "[ ] Commands, [ ] [1]
).
memory") .
functions") .
functions") .
20
A N D
Section 3.4 "[ ]
Codes") .
zones") .
S