Keypad Commands - DSC Power832 Installation Manual

All keypads provide complete information and control of the alarm panel. The panel can be completely programmed
via any keypad on the system. LED keypads provide function indicator lights and individual zone indicator lights for
the alarm circuits. The LCD keypad provides function indicator lights and word descriptions for zone status.
The following sections describe how to arm, disarm and perform other keypad functions.
3.1 Access Codes
The panel has a total of 37 Access Codes available.
Access Codes [01] to [32] .. User Codes 1 to 32
Access Code [33] .............. Partition 1 Duress Code
Access Code [34] .............. Partition 2 Duress Code
Access Code [40] .............. System Master Code
Access Code [41] .............. Partition 1 Master Code
Access Code [42] .............. Partition 2 Master Code
System Master Code
The System Master Code Not Changeable System Master Code Not Changeable System Master Code Not Changeable System Master Code Not Changeable option can be used to lock in the code. This will prevent the System Master Code Not Changeable
user from being able to change the System Master Code. If they attempt to change the code the keypad
will sound a long error beep. The System Master Code can be used to arm or disarm any partition and
perform any keypad function.
If the code is lost it can be reprogrammed through Installer Programming.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
System Master Code Not Changeable .......... Section [015], Option [6]
System Master Code ..................................... Section [007]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Partition Master Codes
By default the Partition Master Codes are not programmed. They must be programmed by the System
Master Code. A Partition Master, once programmed, can be used to arm and disarm the Partition it is
assigned to. In addition, a Partition Master can program the 32 User Codes to operate on the Partition it is
assigned to and program the Partition Duress Code.
Partition Duress Codes
By default Partition Duress Codes are not programmed. They must be programmed by the System Master
Code or the Partition Master Code for that Partition. Once programmed if the Duress Code is used any
time, the panel will activate a silent Duress alarm (See
User Codes
By default the 32 User Codes are not programmed. They must be programmed by the System Master
Code or Partition Master Code. Once programmed the User Code can be used to arm or disarm any
Partition it is enabled for. In addition, each User Code can be enabled or disabled for bypass ability (See
Section 3.4 "[ ] Commands, [ ] [1] Zone
Maintenance Code
The Maintenance Code is an access code that can only arm/disarm the panel. It cannot be used to
bypass zones. This code cannot be used to access the system by the Escort5580. The code can be used
for service personnel.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Maintenance Code ........................................ Section [008]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
3.2 Arming / Disarming
The system cannot be armed unless the 'Ready' light is on. If the 'Ready' light is not on make sure all
protected doors and windows are secure and stop movement in areas covered by motion detectors.
When the 'Ready' light is on enter any valid Access Code. As each digit is pressed the keypad will beep.
If an incorrect code is entered the keypad will emit a steady 2 second beep to indicate the code was not
correct. If the code is correct but the 'Ready' light was not on the panel will beep six times rapidly followed
by a long two second beep to indicate the system was not Ready. When the correct code is entered and
the system is Ready the panel will beep six times rapidly and the 'Armed' light will turn on. Exit the
premises through the designated entry/exit door. Other methods of arming are available (See
"[ ] Commands - [ ] [0] Quick Arm, [ ] [9] Arming Without Entry Delay"

Keypad Commands

S E C T
Bypass") and for accessing the system by the Escort5580.
I O N 3
Section 5.7 "Communicator - Reporting
and
13
Codes") .
Section 3.4
Section 3.5 "Function Keys") .