Tenda DH301 User Manual
  1. Manuals
  2. Brands
  3. Tenda Manuals
  4. Network Router
  5. DH301
  6. User manual

Tenda DH301 User Manual

Wireless n300 adsl2+ high power modem router
Hide thumbs
Table of Contents

Advertisement

Quick Links

Wireless N300 ADSL2+ High Power Modem Router
i

Advertisement

Table of Contents
loading

Related Manuals for Tenda DH301

Summary of Contents for Tenda DH301

  • Page 1 Wireless N300 ADSL2+ High Power Modem Router...

  • Page 2: Copyright Statement

    Tenda reserves the right to make changes to the products without obligation to notify any person or organization of such revisions or changes. Tenda does not assume any liability that may occur due to the use or application of the product described herein.
  • Page 3 Wireless N300 ADSL2+ High Power Modem Router Contents Chapter 1 Get to Know Your Router ............................. 1 1.1 What it does ................................1 1.2 Product Features ..............................1 1.3 Package Contents ..............................2 Chapter 2 Hardware Install ..............................3 2.1 LED Indicators, Buttons and Interfaces ........................3 2.2 Install the Device ..............................
  • Page 4 Wireless N300 ADSL2+ High Power Modem Router 4.3.4 Wireless Bridge ............................136 4.3.5 Station Info ............................... 137 4.4 Diagnostics ................................138 4.4.1 Diagnostics ............................... 138 4.4.2 Ping test ..............................138 4.5 Management ................................ 139 4.5.1 Settings ..............................139 4.5.2 System Log .............................. 141 4.5.3 SNMP Agent ............................

  • Page 5: Product Features

    Wireless N300 ADSL2+ High Power Modem Router Chapter 1 Get to Know Your Router 1.1 What it does The Wireless N300 ADSL2+ High Power Modem Router provides you with an easy and secure way to set up a wireless home network with fast access to the Internet over a high-speed digital subscriber line (DSL). Complete with a built-in ADSL modem, it is compatible with all major ADSL Internet service providers.

  • Page 6: Package Contents

    Other Advanced Features: IPv6, DDNS, virtual server, DMZ, port triggering, IP filter, MAC filter and UPnP, etc. Tenda Setup Wizard for easy and fast installation and configuration Tenda Green: Use hardware Power On/Off and software WiFi On/Off buttons to turn on and off power and WiFi to save energy when not in use 1.3 Package Contents...

  • Page 7: Front Panel

    Wireless N300 ADSL2+ High Power Modem Router Chapter 2 Hardware Install If you have not set up your new router using the Install Guide that comes in the box, this chapter walks you through the hardware install. To set up your Internet connection, see Chapter 3 Quick Internet Setup.

  • Page 8: Back Panel

    Wireless N300 ADSL2+ High Power Modem Router No connection established 4/iTV Blinking Transmitting data 1/WAN Solid Connection is established. Solid Client connected successfully. Blinking WPS LED starts blinking if you press the WPS button on the device or interface. No wireless clients are connected. WPS LED turns off after blinking for 2 minutes. Solid Connection is successfully established on the USB port.

  • Page 9: Install The Device

    Wireless N300 ADSL2+ High Power Modem Router Used to connect to the power adapter, which is included in the package. ON/OFF Power switch to turn the router on or off. 2.2 Install the Device Connect the included power adapter to your router and turn on the router. ①...

  • Page 10: Internet Setup

    Wireless N300 ADSL2+ High Power Modem Router Chapter 3 Quick Internet Setup This chapter instructs you to quickly set up your Internet connection. 3.1 Log in to Web Manager 1. Set your PC to Obtain an IP address automatically. For more information, see Appendix 1 Configure Your 2.
  • Page 11 Wireless N300 ADSL2+ High Power Modem Router Depending on the type of connection, you are prompted to enter your ISP settings, as shown in the following table: Connection Type Description Enter the ISP user name and password. If you cannot locate this information, ask PPPoE/PPPoA your ISP to provide it.

  • Page 12: Ethernet Mode

    Wireless N300 ADSL2+ High Power Modem Router When Bridge mode is enabled, this device works as a modem. If you wish to initiate a dialup directly from your PC for Internet access or enjoy the entire Internet Bridge connection by yourself (instead of sharing it with others), you can select Bridge. Note If your country and/or your ISP are not covered on the home page, select Other country and ISP, and set VCI and VPI value manually.

  • Page 13: Test Internet Connectivity

    Wireless N300 ADSL2+ High Power Modem Router Depending on the type of connection, you are prompted to enter your ISP settings, as shown in the following table: Connection Type ISP Information PPPoE No entries are needed. Enter the assigned IP address, subnet mask, and the IP address of your ISP’s primary Static IP DNS server provided by your ISP.

  • Page 14: Chapter 4 Advanced Settings

    Wireless N300 ADSL2+ High Power Modem Router Chapter 4 Advanced Settings If you prefer configuring your router for unique situations, consult this chapter to know advanced features. Click Advanced on the home page to enter the screen below.

  • Page 15: Device Info

    Wireless N300 ADSL2+ High Power Modem Router 4.1 Device Info 4.1.1 Summary Here you can view system information and current status of your WAN connection as seen in the screenshot.

  • Page 16: Statistics

    Wireless N300 ADSL2+ High Power Modem Router 4.1.2 WAN Here you can view the WAN Information including Interface, Description, Type, IGMP, NAT, Firewall, Status, IPv4 Address, etc. 4.1.3 Statistics Here you can view the packets received and transmitted on LAN and WAN ports. Statistics--LAN: Displays the packets received and transmitted on the LAN ports as seen in the screenshot below.

  • Page 17: Route

    Wireless N300 ADSL2+ High Power Modem Router Statistics-xDSL: Display the packets received and transmitted on the DSL port.
  • Page 18 Wireless N300 ADSL2+ High Power Modem Router 4.1.4 Route Here you can view the route table as seen in the screenshot: 4.1.5 ARP Here you can view the IP and MAC addresses of the PCs that attach to the device either via a wired or wireless connection as seen in the screenshot:...

  • Page 19: Advanced Setup

    Wireless N300 ADSL2+ High Power Modem Router 4.1.6 DHCP Here you can view the DHCP leases, including IP and MAC addresses of the PCs, hostnames and remaining lease time as seen in the screenshot: 4.2 Advanced Setup 4.2.1 Layer2 Interface Click Advanced Setup >...
  • Page 20 Wireless N300 ADSL2+ High Power Modem Router To set up the ATM interface Step 1: Select ATM Interface and click Add to configure it. Step 2: Enter the VPI and VCI values. Select a DSL Link Type (Internet connection type): EoA, PPPoA or IPoA. Leave other options unchanged from factory defaults.

  • Page 21: Wan Service

    Wireless N300 ADSL2+ High Power Modem Router Go to To Set up WAN Service for ATM Interface to configure the WAN service for Internet access. If you are unsure about the VPI/VCI parameters, see Appendix 4 VPI/VCI List, or ask your ISP to provide it. To set up the ETH interface Step 1: Select ETH Interface and click Add.

  • Page 22: Wan Service

    Wireless N300 ADSL2+ High Power Modem Router Go to To Set up WAN Service for ETH Interface to configure the WAN service for Internet access. 4.2.2 WAN Service This router provides two WAN services: - WAN Service for ATM Interface (ADSL uplink) - WAN Service for ETH Interface (Ethernet uplink) To Set up WAN Service for ATM Interface EoA (PPPoE, IPoE and Bridge)
  • Page 23 Wireless N300 ADSL2+ High Power Modem Router Step 3: Select PPP over Ethernet (PPPoE). Edit the Enter Service Description field which is optional. Suggest you keep the default. Select a network protocol: IPv4 Only. Click Next.
  • Page 24 Wireless N300 ADSL2+ High Power Modem Router Step 4: Finish PPP Username and Password and other settings on the figure below. Click Next. PPP Username/Password: For logging in to your ISP. If you cannot locate this information, ask your ISP to provide it. PPPoE Service Name: Provided by your ISP.
  • Page 25 Wireless N300 ADSL2+ High Power Modem Router only by cloning the MAC address of your computer can you access the Internet through the router. 2. MTU Short for Maximum Transmission Unit, the largest physical packet size, measured in bytes, which a network can transmit.
  • Page 26 Wireless N300 ADSL2+ High Power Modem Router  Step 7: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.  When the PPPoE connection is successful, you can access the Internet.
  • Page 27 Wireless N300 ADSL2+ High Power Modem Router IPv4 & IPv6 (Dual Stack) Step 1: Click Advanced Setup > WAN Service and then click the Add button. Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next. Step 3: Select PPP over Ethernet (PPPoE).
  • Page 28 Wireless N300 ADSL2+ High Power Modem Router Step 4: Configure PPP Username and Password and other settings on the figure below. Each field with its indication is mentioned above in IPv4 Only (PPPoE) section. Check Launch Dhcp6c for Prefix Delegation (IAPD). Click Next.
  • Page 29 Wireless N300 ADSL2+ High Power Modem Router If your ISP is using static DHCPv6, check Launch Dhcp6c for Address Assignment (IANA) also, or configure a static IP address by checking Use Static IPv6 Address and enter the static IPv6 address. Step 5: To configure the Default Gateway interface when using IPv6, select the interface that you want to configure with the WAN gateway address in Selected WAN Interface box.
  • Page 30 Wireless N300 ADSL2+ High Power Modem Router  When the PPPoE connection is successful, you can access the Internet. IPv6 Only Step 1: Click Advanced Setup > WAN Service and then click the Add button. Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.
  • Page 31 Wireless N300 ADSL2+ High Power Modem Router Step 3: Select PPP over Ethernet (PPPoE). Edit the Enter Service Description field which is optional. Suggest you keep the default. Select a network protocol you need: IPv6 Only. Click Next. Step 4: Configure PPP Username and Password and other settings on the figure below. Each field with its indication is mentioned above in IPv4 Only (PPPoE) section.
  • Page 32 Wireless N300 ADSL2+ High Power Modem Router If ISP provides you with the static IPv6 address, configure a static IP address by checking Use Static IPv6 Address and enter the static IPv6 address. Step 5: To configure the Default Gateway interface when using IPv6, select the interface that you want to configure with the WAN gateway address in Selected WAN Interface box.
  • Page 33 Wireless N300 ADSL2+ High Power Modem Router Step 6: To configure the WAN DNS address, check the Obtain IPv6 DNS info from a WAN interface option, or select the Use the following Static IPv6 DNS address option to enter the static DNS server IPv6 addresses provided by your ISP.
  • Page 34 Wireless N300 ADSL2+ High Power Modem Router  When the PPPoE connection is successful, you can access the Internet. IPoE IPv4 Only If your ISP uses DHCP to assign your IP address or if your ISP assigns you a static (fixed) IP address, IP subnet mask and the gateway IP address, you need to select the IP over Ethernet (IPoE).
  • Page 35 Wireless N300 ADSL2+ High Power Modem Router Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next. Step 3: Select IP over Ethernet. Edit the Enter Service Description which is optional. Suggest you keep the default. Select a network protocol: IPv4 Only.
  • Page 36 Wireless N300 ADSL2+ High Power Modem Router Obtain an IP address automatically: This allows the router to automatically acquire IP information from your ISP or your existing networking equipment. Use the following Static IP address: This allows you to specify the Static IP information provided by your ISP or that corresponds with your existing networking equipment.
  • Page 37 Wireless N300 ADSL2+ High Power Modem Router Step 6: To configure the Default Gateway interface, select the interface that you want to configure with the WAN gateway address in Available Routed WAN Interfaces box and move it into Selected Default Gateway Interfaces box. The default setting is recommended.
  • Page 38 Wireless N300 ADSL2+ High Power Modem Router  When the IPoE connection is successful, you can access the Internet. IPv4 & IPv6 (Dual Stack) Step 1: Click Advanced Setup > WAN Service and then click the Add button. Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.
  • Page 39 Wireless N300 ADSL2+ High Power Modem Router Step 3: Select IP over Ethernet. Edit the Enter Service Description which is optional. Suggest you keep the default. Select a network protocol: IPv4&IPv6 (Dual Stack). Click Next. Step 4: To finish WAN IP Settings, select Obtain an IPv6 address automatically, check Dhcpv6 Prefix Delegation (IAPD).
  • Page 40 Wireless N300 ADSL2+ High Power Modem Router If ISP provides you with the static IPv6 address, configure a static IP address by checking Use the following Static IPv6 address and enter the static IPv6 address. Step 5: Configure NAT settings. If you are unsure about the options, please keep the default settings and then click Next.
  • Page 41 Wireless N300 ADSL2+ High Power Modem Router Step 6: Configure the WAN gateway address. Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected.
  • Page 42 Wireless N300 ADSL2+ High Power Modem Router Step 7: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set. When the IPoE connection is successful, you can access the Internet.
  • Page 43 Wireless N300 ADSL2+ High Power Modem Router IPv6 Only Step 1: Click Advanced Setup > WAN Service and then click the Add button. Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next. Step 3: Select IP over Ethernet (IPoE).
  • Page 44 Wireless N300 ADSL2+ High Power Modem Router Step 4: Enter the WAN information provided by your ISP to configure the WAN IPv6 settings. To obtain an IP address automatically: Select Obtain an IPv6 address automatically. Check Dhcp6c Prefix Delegation (IAPD). If your ISP is using stateful DHCPv6, check Dhcp6c Address Assignment (IANA) also.
  • Page 45 Wireless N300 ADSL2+ High Power Modem Router Step 5: Finish Network Address Translation Settings. Suggest keep the default settings. Click Next. Step 6: To configure the Default Gateway interface when using IPv6, select the interface that you want to configure with the WAN gateway address in Selected WAN Interface box.
  • Page 46 Wireless N300 ADSL2+ High Power Modem Router Step 8: Here you can view your configurations. Click Apply/Save to have this interface to be effective. When the IPoE connection is successful, you can access the Internet.
  • Page 47 Wireless N300 ADSL2+ High Power Modem Router Bridge If you wish to initiate a dialup directly from your PC for Internet access or enjoy the entire Internet connection (instead of sharing it with others), you can use the Bridging DSL link type and create a dialup program on your PC. Step 1: Click Advanced Setup >...
  • Page 48 Wireless N300 ADSL2+ High Power Modem Router Step 4: Here you can view your configurations. Click Apply/Save to have this interface to be effective. After the bridging connection is successful, initiate a dialup directly from your PC for Internet access.

  • Page 49: Ipv4 Only

    Wireless N300 ADSL2+ High Power Modem Router Note To configure multiple WAN connect ions, simply configure multiple ATM interfaces and then follow the instructions above. PPPoA If you have selected the PPPoA from the ATM Interface screen in Layer2 Interface, you will see the screen below when you click the WAN Service tab, select the configured interface and click Next.

  • Page 50: Multicast

    Wireless N300 ADSL2+ High Power Modem Router Step 4: Enter PPP username and its password provided by your ISP. Click Next. PPP Username: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it. PPP Password: This is for logging in to your ISP.

  • Page 51: Wireless

    Wireless N300 ADSL2+ High Power Modem Router Step 5: To configure the WAN gateway address. After you configure it click Next. The default setting is recommended. Step 6: To configure the WAN DNS address. Choose a way to get DNS server according to what your ISP has provided. -Click the Select DNS Server Interface from available WAN interfaces option.
  • Page 52 Wireless N300 ADSL2+ High Power Modem Router 3. If you cannot locate the static DNS server IP information, ask your ISP to provide it. Step 7: Here you can view your configurations. Click Apply/Save to have this interface to be effective. Step 8: When the PPPoA connection is successful, you can access the Internet.
  • Page 53 Wireless N300 ADSL2+ High Power Modem Router Step 3: Edit the Enter Service Description. This field is optional. We recommend that you keep the default. Select a network protocol: IPv4 & IPv6 (Dual Stack). Click Next. Step 4: Enter PPP username and its password provided by your ISP. Click Next.
  • Page 54 Wireless N300 ADSL2+ High Power Modem Router Step 5: To configure the WAN gateway address. After you configure it click Next. The default setting is recommended. Note Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected.
  • Page 55 Wireless N300 ADSL2+ High Power Modem Router Step 6: To configure the WAN DNS address Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. And then click Next. Note 1. DNS Server Interfaces can have multiple WAN interfaces served as system DNS servers but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected.
  • Page 56 Wireless N300 ADSL2+ High Power Modem Router Step 8: When the PPPoA connection is successful, you can access the Internet. IPv6 Only Step 1: Click Advanced Setup > WAN Service and then click the Add button. Step 2: Select the ATM interface you added just now from the pull-down menu in the figure below. Click Next.
  • Page 57 Wireless N300 ADSL2+ High Power Modem Router Step 3: Edit the Enter Service Description. This field is optional. We recommend that you keep the default. Select a network protocol: IPv6 Only. Click Next. Step 4: Enter PPP username and its password provided by your ISP. Click Next.
  • Page 58 Wireless N300 ADSL2+ High Power Modem Router Step 5: Select a preferred wan interface as the system default IPv6 gateway. Click Next. Step 6: To configure the WAN DNS address, select the configured WAN interface for IPv6 DNS server information or enter the static IPv6 DNS server addresses.
  • Page 59 Wireless N300 ADSL2+ High Power Modem Router Note Selecting a WAN interface for IPv6 DNS server will enable DHCPv6 Client on that interface. Step 7: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set. Step 8: When the PPPoA connection is successful, you can access the Internet.
  • Page 60 Wireless N300 ADSL2+ High Power Modem Router IPoA If you have selected the IPoA from the ATM Interface screen in Layer2 Interface, you will see the screen above when you click the WAN Service tab, select the configured interface and click Next. Step 1: Click Advanced Setup >...
  • Page 61 Wireless N300 ADSL2+ High Power Modem Router Step 4: Enter the WAN IP address and subnet mask which should have been provided to you by your ISP. If you cannot locate this information, ask your ISP to provide it. And then click Next. WAN IP Address: The Internet IP address provided by your ISP for accessing the Internet.
  • Page 62 Wireless N300 ADSL2+ High Power Modem Router Step 6: To configure the WAN gateway address. After you configure it click Next. The default setting is recommended. Note Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected.
  • Page 63 Wireless N300 ADSL2+ High Power Modem Router Step 8: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set. Step 9: IPoA WAN service setup parameter is shown as below. To Set up WAN Service for ETH Interface Three Internet connections: PPP over Ethernet (PPPoE), IP over Ethernet (IPoE) and Bridging are available in the Ethernet uplink mode.
  • Page 64 Wireless N300 ADSL2+ High Power Modem Router PPP over Ethernet (PPPoE) IPv4 Step 1: Click Advanced Setup > WAN Service and then click the Add button. Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next. Step 3: Select PPP over Ethernet.
  • Page 65 Wireless N300 ADSL2+ High Power Modem Router Step 4: Enter the PPP username and password provided by your ISP. If you are not sure about other options, just leave them unchanged from defaults. And click Next. PPP Username: This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it. PPP Password: This is for logging in to your ISP.

  • Page 66: Management

    Wireless N300 ADSL2+ High Power Modem Router Authentication Method: This is used by ISP to authenticate the client that attempts to connect. If you are not sure, consult your ISP or select Auto. MAC Clone: Clicking Clone MAC button copies the MAC address of your PC to the router. Many broadband ISPs restrict access by allowing traffic only from the MAC address of your broadband modem, but some ISPs additionally register the MAC address of the network interface card in your computer when your account is first opened.
  • Page 67 Wireless N300 ADSL2+ High Power Modem Router Step 6: Configure the WAN DNS address according to your ISP. -Click the Select DNS Server Interface from available WAN interfaces option; -Or select the Use the following Static DNS IP address option and enter static DNS server IP addresses for the system. And then click Next.
  • Page 68 Wireless N300 ADSL2+ High Power Modem Router IPv4 & IPv6 (Dual Stack) Step 1: Click Advanced Setup > WAN Service and then click the Add button. Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next. Step 3: Select PPP over Ethernet.
  • Page 69 Wireless N300 ADSL2+ High Power Modem Router Step 4: Enter PPP username and PPP password provided by your ISP. Check Launch Dhcp6c for Prefix Delegation (IAPD). If your ISP is using stateful DHCPv6, check Launch Dhcp6c for Address Assignment (IANA) also. Or configure a static IP address.
  • Page 70 Wireless N300 ADSL2+ High Power Modem Router Step 5: Select a avaliable WAN interface as the system default gateway. Then click Next. Step 6: Configure DNS server (Select an available DNS server interface or use a specified DNS server); configure IPv6 DNS server (Obtain IPv6 DNS info from a WAN interface or use a specified DNS server), and then click Next.
  • Page 71 Wireless N300 ADSL2+ High Power Modem Router When the PPPoE connection is successful, you can access the Internet. IPv6 Step 1: Click Advanced Setup > WAN Service and then click the Add button. Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next.
  • Page 72 Wireless N300 ADSL2+ High Power Modem Router Step 3: Select PPP over Ethernet. Edit the Enter Service Description. This field is optional. We recommend that you keep the default. Select a network protocol: IPv6 Only. And click Next. Step 4: Enter PPP username and PPP password provided by your ISP. Check Launch Dhcp6c for Prefix Delegation (IAPD).
  • Page 73 Wireless N300 ADSL2+ High Power Modem Router Step 5: Select a preferred WAN interface from the WAN interface lise as the system default IPv6 gateway. Click Next. Step 6: Select the configured WAN interface for IPv6 DNS server information or use a static IPv6 DNS server address. Note that selecting a WAN interface for IPv6 DNS server will enable DHCPv6 Client on that interface.
  • Page 74 Wireless N300 ADSL2+ High Power Modem Router Step 7: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set. When the PPPoE connection is successful, you can access the Internet.
  • Page 75 Wireless N300 ADSL2+ High Power Modem Router IP over Ethernet (IPoE) If your ISP uses DHCP to assign your IP address or if your ISP assigns you a static (fixed) IP address, IP subnet mask and the gateway IP address, you need to select the IP over Ethernet (IPoE). IPv4 Step 1: Click Advanced Setup >...
  • Page 76 Wireless N300 ADSL2+ High Power Modem Router Step 4: Enter the IP address/subnet mask/gateway IP address provided by your ISP or select Obtain an IP address automatically and then click the Next button. Obtain an IP address automatically: This allows the router to automatically acquire IP information from your ISP or your existing networking equipment.
  • Page 77 Wireless N300 ADSL2+ High Power Modem Router corresponds with your existing networking equipment. WAN IP Address: The Internet IP address provided by your ISP for accessing the Internet. WAN Subnet Mask: The subnet mask address provided by your ISP for accessing the Internet. WAN gateway IP Address: The gateway IP address provided by your ISP for accessing the Internet.
  • Page 78 Wireless N300 ADSL2+ High Power Modem Router And then click Next. Step 8: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set. When the IPoE connection is successful, you can access the Internet.
  • Page 79 Wireless N300 ADSL2+ High Power Modem Router IPv4 & IPv6 (Dual Stack) Step 1: Click Advanced Setup > WAN Service and then click the Add button. Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next. Step 3: Select IP over Ethernet as WAN service type.
  • Page 80 Wireless N300 ADSL2+ High Power Modem Router Step 4: Enter information provided by your ISP to configure the WAN IP settings.
  • Page 81 Wireless N300 ADSL2+ High Power Modem Router Step 5: Here you can configure the NAT. If you are not an advanced user we recommend you to keep the default settings and then click Next. Step 6: Configure a WAN interface as the default gateway. Step 7: Configure DNS server (Select an available DNS server interface or use a specified DNS server);...
  • Page 82 Wireless N300 ADSL2+ High Power Modem Router Step 8: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set. When the IPoE connection is successful, you can access the Internet.
  • Page 83 Wireless N300 ADSL2+ High Power Modem Router IPv6 Step 1: Click Advanced Setup > WAN Service and then click the Add button. Step 2: Select the ETH interface you added just now from the pull-down menu in the figure below. Click Next. Step 3: Select IP over Ethernet as WAN service type.
  • Page 84 Wireless N300 ADSL2+ High Power Modem Router Step 4: Enter the WAN information provided by your ISP to configure the WAN IPv6 settings. To obtain an IP address automatically: Select Obtain an IPv6 address automatically and Check Dhcp6c Prefix Delegation (IAPD). If your ISP is using stateful DHCPv6, check Dhcp6c Address Assignment (IANA) also.
  • Page 85 Wireless N300 ADSL2+ High Power Modem Router Step 5: Here you can configure the NAT. If you are not an advanced user we recommend you to keep the default settings and then click Next. Step 6: To configure the Default Gateway interface when using IPv6, select the interface that you want to configure with the WAN gateway address in Selected WAN Interface box.
  • Page 86 Wireless N300 ADSL2+ High Power Modem Router Step 7: To configure the WAN DNS address, check the Obtain IPv6 DNS info from a WAN interface option, or select the Use the following Static IPv6 DNS address option to enter the static DNS server IPv6 addresses provided by your ISP.
  • Page 87 Wireless N300 ADSL2+ High Power Modem Router When the IPoE connection is successful, you can access the Internet. Bridging If you wish to initiate a dialup directly from your PC for Internet access or enjoy the entire Internet connection (instead of sharing it with others), you can select the Bridging and create a dialup program on your PC.
  • Page 88 Wireless N300 ADSL2+ High Power Modem Router Step 3: Select Bridging. Edit the Enter Service Description. This field is optional. We recommend that you keep the default. And click Next. Step 4: Here you can view your configurations. Click Apply/Save to save your settings if everything is correctly set.
  • Page 89 Wireless N300 ADSL2+ High Power Modem Router After the bridging connection is successful, initiate a dialup directly from your PC for Internet access. Note The device functions as a switch in Bridge mode -Ethernet uplink. 4.2.3 LAN Here you can configure the LAN IP address and subnet mask. This IP address is to be used to access the device’s settings through a web browser.
  • Page 90 Wireless N300 ADSL2+ High Power Modem Router IP Address/Subnet Mask: The device's LAN IP address and subnet mask that both you can change to fit your network. The default IP address is 192.168.1.1. If you change the LAN IP address, you should use the new address to access the management interface next time.

  • Page 91: Ipv6 Autoconfig

    Wireless N300 ADSL2+ High Power Modem Router address to access the Internet, you can check Disable DHCP Server. 4) Start/End IP Address: Specify the start/end of the range for the IP address pool in the same subnet as the router. Only enabling DHCP server need you to finish this part configurations.
  • Page 92 Wireless N300 ADSL2+ High Power Modem Router Interface Address: Enter the interface address with prefix length. E.g., the interface IPv6 address is “2000::1/64”,  then you need to input http://[2000::1] in the browse address bar to access the device management interface. ...

  • Page 93: Virtual Server

    Wireless N300 ADSL2+ High Power Modem Router  Click Save/Apply. Other fields’ introduction that may help: Enable ULA Prefix Advertisement: If enabled, the router will advertise ULA prefix periodically.  Leased Time (hour): A time length that the IP address is assigned to each device before it is refreshed. ...
  • Page 94 Wireless N300 ADSL2+ High Power Modem Router  User Interface: Select the WAN interface you will use to visit the server in your LAN.   Configure the Service Name > Select a Service to select an existing service (Select One here is only an express to tell you select one service.) from the drop-down list.
  • Page 95 Wireless N300 ADSL2+ High Power Modem Router Server page that the UPnP interface is being used. Application Scenario: You have set up one web server on the LAN. Web server——IP: 192.168.1.50, TCP port: 8090. Now you hope friends on the Internet can access your web by Port 10480 through WAN port. WAN port——ipoe_eth0.1, IP: 1.2.3.4 Configuration Steps: Click Advanced Setup >...

  • Page 96: Port Triggering

    Wireless N300 ADSL2+ High Power Modem Router Result: Your friend on the Internet will be able to access your web server simply by entering “http://1.2.3.4:10480” in browser. Actually if you set the DNS in 4.2.9 DNS, your friend can also enter http://domain name:10480 to access your web server.
  • Page 97 Wireless N300 ADSL2+ High Power Modem Router Here in the Port Triggering interface, you can configure the port settings by selecting an existing application or creating your own (Custom application).  User Interface: Select the WAN interface you will use to visit the server in your LAN. ...

  • Page 98: Dmz Host

    Wireless N300 ADSL2+ High Power Modem Router DMZ Host The default DMZ (De-Militarized Zone) host feature is helpful when you are using some online games and videoconferencing applications that are not compatible with NAT (Network Address Translation). Note that enabling DMZ host means the built-in firewall of your router takes no effect, and your computer that’s set as the DMZ host will totally expose itself to the Internet.
  • Page 99 Wireless N300 ADSL2+ High Power Modem Router 4.2.5 Security This section explains the following information: • IP Filtering • MAC Filtering IP Filtering Outgoing IP Filtering Setup By default, all outgoing IP traffic from LAN is allowed, but some IP traffic can be BLOCKED by setting up filters. Choose Add or Remove to configure outgoing IP filters.
  • Page 100 Wireless N300 ADSL2+ High Power Modem Router Protocol: TCP/UDP, TCP, UDP and ICMP are available for your option. Source IP address [/prefix length]: Enter the [LAN IP address/prefix length] to be filtered. Source Port (port or port: port): Specify a port number or a range of ports used by LAN PCs to access the Internet. If you are unsure, leave it blank.

  • Page 101: Mac Filtering

    Wireless N300 ADSL2+ High Power Modem Router IP Version: Select the IP version that the filter rule supports. Here is IPv4. Protocol: TCP/UDP, TCP, UDP and ICMP are available for your option. Source IP address [/prefix length]: Enter the Internal IP address [/prefix length] to be filtered. Source Port (port or port:port): Specify a port number or a range of ports used by PCs from external network to access your internal network.

  • Page 102: Parental Control

    Wireless N300 ADSL2+ High Power Modem Router Click Add to enter the following screen: Here you can create a filter to identify the MAC layer frames by specifying at least one condition below. If multiple conditions are specified, all of them take effect. Click Save/Apply to save and activate the filter. Protocol Type: Select a protocol type from the drop-down list.

  • Page 103: Url Filter

    Wireless N300 ADSL2+ High Power Modem Router User Name: Enter a user name. Browser's MAC Address: Automatically adds the MAC address of the attached LAN device where the browser is running. Other MAC Address: Specify the MAC address of the computer that you want to apply Internet access restriction. Days of the week: Select the days of the week during which you wish to restrict Internet access.

  • Page 104: Bandwidth Control

    Wireless N300 ADSL2+ High Power Modem Router URL Address: Enter the URL you want to control the access. It can be a complete url address www.google.com, or a part of the domain, like “google”. Note If you have accessed the URL before you include it in a URL filter rule, you must reboot the router and erase it from your PC to activate this URL filter rule.
  • Page 105 Wireless N300 ADSL2+ High Power Modem Router Description: Enter the description of the controlled host. IP Address Range: Enter the IP address of the host you want to control. It can be hosts or a single host. If you want to limit a single IP address’s bandwidth, just keep the start IP same with the end IP, like 192.168.1.2-2 Max Upstream Speed (Kbp/s): Set the max upstream speed.

  • Page 106: Default Gateway

    Wireless N300 ADSL2+ High Power Modem Router Default Gateway Default gateway interface list can have multiple secondary WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected.
  • Page 107 Wireless N300 ADSL2+ High Power Modem Router Click Add to enter the following screen: IP Version: Select IPv4 or IPv6. Destination IP address/prefix length: Enter the destination IP address and prefix length of the final destination. Interface: Select an interface from the drop-down list. Gateway IP Address: Enter the gateway IP address, which must be a router on the same LAN segment as the router.
  • Page 108 Wireless N300 ADSL2+ High Power Modem Router 4.2.9 DNS DNS Server (Static DNS) The DNS server translates domain names to numeric IP addresses. It is used to look up site addresses based on their names. Select DNS Server Interface from available WAN interfaces or enter static DNS server IP addresses for the system. Here you can configure the WAN DNS address: For IPv4: -Click the Select DNS Server Interface from available WAN interfaces option;...
  • Page 109 Wireless N300 ADSL2+ High Power Modem Router Note 1. DNS Server Interfaces can have multiple WAN interfaces served as system DNS servers but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected.
  • Page 110 Wireless N300 ADSL2+ High Power Modem Router Click the Add button to configure the DDNS settings. D-DNS Provider: Select your DDNS service provider from the drop-down menu. It supports three kinds of D-DNS service: DynDNS.org, TZO and NO-IP. Hostname: Enter the DDNS domain name registered with your DDNS service provider. Interface: Specify a WAN connection interface.
  • Page 111 Wireless N300 ADSL2+ High Power Modem Router Hostname: xhh3793.dyndns.org Add Dynamic DNS Select DynDNS.org from the D-DNS provider drop-down list. Enter your Dyndns hostname. Here is “xhh3793.dyndns.org” as an example. Specify a WAN connection interface. DynDNS Settings Enter your DynDNS username. Here is “qiangweianbian” as an example. Enter the password of your DynDNS.org account.
  • Page 112 Wireless N300 ADSL2+ High Power Modem Router...
  • Page 113 Wireless N300 ADSL2+ High Power Modem Router 4.2.10 DSL This screen provides multiple ASDL modulation modes to meet diversified environments. You can also select phone line pair and Capability. DSL parameter configurations must be supported by ISP to take effect. Actual parameters (see Statistics-xDSL) resulted from the negotiation between your router and ISP.

  • Page 114: Windows 8

    Wireless N300 ADSL2+ High Power Modem Router Here you can select the test mode and tone. If you are unsure about the ADSL parameters, please apply the factory default settings. Wrong configurations may fail your Internet access. 4.2.11 UPnP UPnP (Universal Plug and Play) allows Windows based systems to configure the device for various Internet applications automatically.

  • Page 115: Print Server

    Wireless N300 ADSL2+ High Power Modem Router Enable UPnP: Check/uncheck to enable/disable the UPnP feature. Note UPnP is activated only when there is a live WAN service with NAT enabled. 4.2.12 Print Server Enabling the Print Server makes all PCs in the LAN have an access to the USB printer which has been connected to this router.

  • Page 116: Windows 7

    Wireless N300 ADSL2+ High Power Modem Router USB printing config: Step 1: Connect the USB printer to the USB port of the device. Step 2: Enable USB printing service of the device (the router). ① Enter the name of the USB printer in Printer name box. ②...
  • Page 117 Wireless N300 ADSL2+ High Power Modem Router Click Next; ② Select A network printer, or a printer attached to another computer and click Next; ③...
  • Page 118 Wireless N300 ADSL2+ High Power Modem Router Select Connect to a printer on the Internet or on a home or office network, type in ④ “http://192.168.1.1:631/printers/hp3845” in the URL field and click Next; Note: Here “192.168.1.1” refers to this router’s LAN IP address and “hp3845” refers to the USB printer name you’ve filled in on the Print Server Settings page (See Step 2).
  • Page 119 Wireless N300 ADSL2+ High Power Modem Router Click Browse, select driver file directory on CD-ROM and click OK; ⑥ Select the manufacturer and the model of your printer. And click OK. ⑦...

  • Page 120: Windows 8

    Wireless N300 ADSL2+ High Power Modem Router Choose “Yes” or “No” for default printer setting and click Next. ⑧ Click Finish. ⑨ Check the status of printer from Windows “Control Panel”, printer window. Status should be shown “ready”.

Table of Contents