Download  Print this page

GE C30 Instruction Manual Page 64

Controller system ur series.
Hide thumbs
   
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
Table of Contents
441

Advertisement

Table of Contents
3.2 WIRING
CONTACT INPUTS:
A dry contact has one side connected to terminal B3b. This is the positive 48 V DC voltage rail supplied by the power sup-
ply module. The other side of the dry contact is connected to the required contact input terminal. Each contact input group
has its own common (negative) terminal which must be connected to the DC negative terminal (B3a) of the power supply
module. When a dry contact closes, a current of 1 to 3 mA will flow through the associated circuit.
A wet contact has one side connected to the positive terminal of an external DC power supply. The other side of this contact
is connected to the required contact input terminal. If a wet contact is used, then the negative side of the external source
must be connected to the relay common (negative) terminal of each contact group. The maximum external source voltage
for this arrangement is 300 V DC.
The voltage threshold at which each group of four contact inputs will detect a closed contact input is programmable as
17 V DC for 24 V sources, 33 V DC for 48 V sources, 84 V DC for 110 to 125 V sources, and 166 V DC for 250 V sources.
3
Wherever a tilde "~" symbol appears, substitute with the slot position of the module.
NOTE
Contact outputs may be ordered as form-a or form-C. The form-A contacts may be connected for external circuit supervi-
sion. These contacts are provided with voltage and current monitoring circuits used to detect the loss of DC voltage in the
circuit, and the presence of DC current flowing through the contacts when the form-A contact closes. If enabled, the current
monitoring can be used as a seal-in signal to ensure that the form-A contact does not attempt to break the energized induc-
tive coil circuit and weld the output contacts.
There is no provision in the relay to detect a DC ground fault on 48 V DC control power external output. We recom-
mend using an external DC supply.
NOTE
GENERAL APPLICATION CONSIDERATIONS:
Contacts outputs of protective relays, auxiliary contacts from breakers, disconnectors and other devices, are generally con-
nected to contacts inputs of protective relays. In some situations, the contact outputs of some protective relays can have
high impedance connected across it. When such a contact output is connected across a C30 contact input, it can spuri-
ously operate the C30 input even when the output is open, if there is a substantial distributed capacitance (represented by
C1) present in the wiring between the output and the C30 input and the debounce time setting in the C30 relay is low
enough. This false assertion of the contact input, when there is inadvertent ground present at the DC positive terminal, can
be prevented by inserting a resistor across the C30 input.
3-18
(Dry)
DIGITAL I/O
6B
~
7a
+
~
CONTACT IN
7a
~ 7c
+
~
CONTACT IN
7c
~
8a
+
CONTACT IN
~
8a
+
~
8c
CONTACT IN
~
8c
-
~
7b
COMMON
~
7b
SURGE
~
8b
B
1b
CRITICAL
B
1a
FAILURE
2b
B
B
3a
-
48 VDC
B
3b
+
OUTPUT
B
5b HI+
CONTROL
B
6b LO+
POWER
B
6a
-
8a
B
SURGE
B
8b
FILTER
Figure 3–17: DRY AND WET CONTACT INPUT CONNECTIONS
C30 Controller System
(Wet)
DIGITAL I/O
~
7a
+
CONTACT IN
~
7c
+
CONTACT IN
~
8a
+
CONTACT IN
24-250V
+
~
8c
CONTACT IN
-
~
7b
COMMON
SURGE
~
8b
827741A4.CDR
3 HARDWARE
6B
~
7a
~
7c
~
8a
~
8c
~
7b
GE Multilin

Advertisement

Table of Contents

   Also See for GE C30

   Related Manuals for GE C30

Comments to this Manuals

Symbols: 0
Latest comments: