Specifications And Dimensions - Nakanishi E3000 Operation Manual

6 . SPECIFICATIONS AND DIMENSIONS

6 - 1 Speci cation of the CONTROLLER
Product Name
Model
Input Voltage
Output
Speed Range
Over Voltage Category
Short Circuit Current Rating
Pollution Degree
Input
Signal
External
Control Signal
Output
Signal
Protection Function
Weight
Dimensions
Temperature
Operation Humidity
Environment
Atmospheric
Pressure
Temperature
Transportation
Humidity
and Storage
Atmospheric
Environment
Pressure
Height above Sea Level
* Note 1 : Motor Speed Limited Area
Motor Speed limits depend on the Motor Model. Before using it, check the speci cations of the motor and the motor spindle.
Since CONTROLLER will automatically recognize the motor types, there is no need to adjust the maximum rotation speed
based on the motor model.
3080 J MOTOR AND HES 810 SYSTEM USERS
・ FOR EM-
This motor / spindle is designed to machine at min
The 1 , 000 to 19 , 000 min are for warm-up purpose only.
Do not machine at a Speed of less than 20 , 000 min
・ Control limits motor speed from
EM 20 - S 6000 .
・ Control limits motor speed from
・ Control limits motor speed from
・ Control limits motor speed from
CAUTION
・ The brushless motor " EM-3030T-J / EM-3030T-J-2M " should be connected to the Applicable
CONTROLLER (Refer to " Table. 2 Identifying the Applicable CONTROLLER ").
If the brushless motor " EM-3030T-J / EM-3030T-J-2M " connected to non applicable
CONTROLLER, brushless motor " EM-3030T-J / EM-3030T-J-2M " will not rotate and Error " EL "
(Incompatible Motor) will be displayed on the Digital Speed Indicator, indicating a " Detection of
unsafe operating conditions " of the CONTROLLER.
54
E 3000 CONTROLLER
NE 211
AC 100 - 240 V, 50 / 60 Hz, 1 PHASE, 1 . 8 A
AC 33 V, 0 - 1 KHz, 3 PHASE, 2 . 4 A
1 , 000 - 80 , 000 min
Ⅱ
63 A
Class 2
Input : Digital 9 (Photo Coupler)
Analog 1
Output : Photo Coupler 1 , MOS Relay 9
Relay Contact 2 , Analog 3
Excess Current, Over Voltage, Motor Sensor Malfunction, CONTROLLER
Overheat, Brake Circuit Trouble, Rotor Lock, Low Air Pressure, Torque Over
Load, Communication Interception, External Control Signal Error, Incompatible
Motor, Over Speed, Emergency Stop Error, Internal Memory Error
2 . 8 kg
W 88 x D 138 x H 238 mm
0 - 40 ° C
MAX. 75 % (No condensation)
800 - 1 , 060 hPa
- 10 - 50 ° C
10 - 85 %
500 - 1 , 060 hPa
Less than 2000 m
- 1
(rpm) 's between 20 , 000 and 80 , 000 min
- 1
(rpm).
- 1
1 , 000 to 60 , 000 min (rpm) for EM - 3060 , EM- 3060 J, EM 30 - S 6000 , EM 25 - S 6000 and
- 1
1 , 000 to 50 , 000 min (rpm) for EM 25 N - 5000 and HES 510 .
- 1
1 , 000 to 32 , 000 min (rpm) for EM - 3030 J, EMA - 3020 K and EMA - 3020 S.
- 1
1 , 000 to 30 , 000 min (rpm) for EM- 3030 T-J, EM- 3030 T-J- 2 M.
- 1
(rpm) *Note 1
- 1
(rpm) only.