Instruction For Use; Cb Technique; Primary Air; Secondary Air - SCAN 65-1 Assembly And Instruction Manual

20
CB technology (Clean Burn)
The stove is equipped with CB technology. In order to ensure optimal
combustion of gases released during the combustion process, air pas-
ses through a specially developed system of channels. The heated air
A
is conducted into the combustion chamber through the holes in the
rear lining of the combustion chamber and at the baffle plates. This
airflow is driven by the combustion rate and cannot be regulated.
NOTE:
Wood must never be added above the CB rail.

Primary air

The primary air regulation mechanism is used for lighting the fire,
or to boost the burning process when you put wood on. The primary
air vent is used when you use hard wood fuel such as oak and beech.
The primary air vent can be closed if you use soft wood such as birch
or pine for fuel.
Settings for normal load: 0-30%

Secondary air

Secondary air is pre-heated and fed indirectly to the fire. At the same
time, the secondary airflow cleans the glass pane to prevent build-up
of soot. If you over-restrict the secondary airflow, soot can build up
on the glass pane. The secondary airflow determines the heat output
from your stove.
Settings for normal load: 50-70%

Baffle plates

CB-technique
B

Handle for riddling grate

Brændkammerforing
Scan 64
NAVN: EMNE:
MATERIALE:
DIMENSION:
C:\Working Folder\Designs\Scan 64\90064036.idw
STI:
Primary air
I N S T R U C T I O N S F O R U S E
Scan 64
NAVN:
MATERIALE:
DIMENSION:
C:\Working Folder\Designs\Scan 64\90064037.idw
STI:
TG.NR:
13-07-11
N/A DATO:
VÆGT:
N/A
AREAL:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
Ash drawer
Secondary air
Baffle plates
The baffle plates are located in the upper part of the combustion
chamber. The plates hold back smoke, making sure it stays inside the
combustion chamber for a longer time before escaping through the
chimney. This reduces the flue gas temperature as the gases have
more time to dissipate heat to the stove. The baffle plates must be
removed for sweeping; see "Maintaining your wood-burning stove".
Note that the baffle plates are made of porous, ceramic material, and
are liable to break easily. You should therefore handle them with care.
The baffle plates are subject to wear and tear and not covered by the
warranty.
Ash container
Open the door of the stove to access the ash container under the
combustion chamber.
The ash container must always be closed during operation.
The ash container must not be become too full and must therefore be
emptied at regular intervals.
Handle for riddling grate
The stove is equipped with a riddling grate that empties ash from the
combustion chamber down into the ash container when activated.
The riddling grate must remain half open while the wood stove is lit.
Adjustment of air supply,
primary and secondary damper
100%-0%
Spjæld, askeskuffe og støbejernsbund
EMNE:
IMPORTANT!
This screw (M5X6) must
be placed as shown in the
picture,to prevent secondary
air control closure beyond the
35mm open position .
90064036
BC
SIGN:
0%-100%
N/A
DATO:
VÆGT:
N/A
AREAL:
A
A
Scan 64 Skrue til england
NAVN: EMNE:
MATERIALE: VÆGT: N/A DATO: 24-03-2015
DIMENSION: AREAL: N/A Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
STI: C:\Working Folder\CAD\Inventor 2015\Templates\Standard - Manual.idw
Scan 64 Skrue til england
NAVN: EMNE:
MATERIALE: VÆGT: N/A
N/A
DIMENSION: AREAL:
C:\Working Folder\CAD\Inventor 2015\Templates\Standard - Manual.idw
STI:
21
900640
TG.NR:
30-08-12 BC
SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
TG.NR: 90064053
SIGN: hms
90064053
TG.NR:
DATO: 24-03-2015 SIGN: hms
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©