Pgm Deactivation Event; Pgm Delay; Pgm Normal State; Pgm2 Strobe Options - Paradox Spectra 1759EX V1.0 Reference & Installation Manual

1 0 . 2 P G M D E A C T I V A T I O N E V E N T
S e c t i o n s [ 1 2 1 ] , [ 1 2 3 ] , [ 1 2 5 ]
After PGM activation, the PGM will return to its normal state (deactivate) when the programmed PGM Deactivation Event occurs.
Instead of deactivating the PGM when a specific event occurs, the PGM can deactivate after a programmed period elapses (see
PGM Delay). For the Event List see the PGM Table in the Spectra 1759EX Programming Guide. If using the PGM Delay, these
sections can be used as a second activation event.
1) Enter section that represents the desired PGM. PGM1 = [121], PGM2 = [123], Global PGM = [125]
2) Enter the Event Group #.
3) Enter the Sub-Group #.
4) Enter the Partition #
01 = Partition 1
02 = Partition 2
99 = Both Partitions
1 0 . 3 P G M D E L A Y
S e c t i o n [ 0 6 6 ] = P G M 1 , [ 0 6 7 ] = P G M 2 , [ 0 6 8 ] = G l o b a l P G M
001 to 255 seconds, 000 = Follows Deactivation Event, Default = 5 seconds
Instead of deactivating the PGM on the occurrence of a specific event, the PGM will deactivate after the period programmed here
has elapsed.
If a PGM Delay is programmed, the deactivation event can be used as a second activation event.
1 0 . 4 P G M N O R M A L S T A T E
S e c t i o n [ 1 2 6 ] : O p t i o n s
A PGM toggles to its opposite state (i.e. a normally open PGM will close) when a specific event has occurred in the system. You
can program each PGM output to be normally open (N.O.) or normally closed (N.C.) by enabling or disabling options [4], [5] and
[6] in section [126].
O p t i o n O F F = P G M 1 N o r m a l l y C l o s e d ( D e f a u l t )
[ 4 ]
O p t i o n O N = P G M 1 N o r m a l l y O p e n
[ 4 ]
O p t i o n O F F = P G M 2 N o r m a l l y C l o s e d ( D e f a u l t )
[ 5 ]
O p t i o n O N = P G M 2 N o r m a l l y O p e n
[ 5 ]
O p t i o n O F F = G l o b a l P G M N o r m a l l y C l o s e d ( D e f a u l t )
[ 6 ]
O p t i o n O N = G l o b a l P G M N o r m a l l y O p e n
[ 6 ]
1 0 . 5 P G M 2 S T R O B E O P T I O N S
S e c t i o n [ 1 2 9 ] : G e n e r a l O p t i o n s
O p t i o n O F F = P G M 2 O u t p u t i s S t e a d y ( D e f a u l t )
[ 1 ]
O p t i o n O N = P G M 2 O u t p u t i s P u l s e d ( S t r o b e )
[ 1 ]
With option [1] enabled, PGM2 will flash on and off whenever activated. Otherwise, it will provide a steady output.
O p t i o n O F F = D i s a b l e P G M 2 P u l s e W h e n S y s t e m i s A r m e d ( D e f a u l t )
[ 2 ]
O p t i o n O N = E n a b l e P G M 2 P u l s e W h e n S y s t e m i s A r m e d
[ 2 ]
Whenever the system is armed, PGM2 will flash once every 30 seconds until the system is disarmed.
O p t i o n O F F = D i s a b l e P G M 2 P u l s e o n A r m / D i s a r m ( D e f a u l t )
[ 3 ]
O p t i o n O N = E n a b l e P G M 2 P u l s e o n A r m / D i s a r m E n a b l e d
[ 3 ]
With this option enabled, PGM2 will flash once to indicate the system has been armed and will flash twice to indicate that the
system has been disarmed.
1 0 . 6 A L A R M R E L A Y O P T I O N S
S e c t i o n [ 1 2 7 ] : G e n e r a l O p t i o n s
O p t i o n O F F = A l a r m R e l a y F o l l o w s B e l l O u t p u t ( D e f a u l t )
[ 7 ]
O p t i o n O N = A l a r m R e l a y F o l l o w s G l o b a l P G M
[ 7 ]
With this option off, the optional Alarm Relay will activate or deactivate whenever the Bell Output activates or deactivates. With
the option on, the Alarm Relay will activate or deactivate whenever Global PGM activates or deactivates.
R & I
4 0 EFERENCE NSTALLATION
, a n d
[ 4 ] [ 5 ] [ 6 ]
M
ANUAL