Viewing The Wireless Transmitter Signal Strength; Serial Number Display - Paradox Spectra 1759EX V1.0 Reference & Installation Manual

6.1.2 D
ELETING
S e c t i o n s [ 6 0 1 ] t o [ 6 0 8 ]
How Do I Delete Assigned Wireless Transmitters?
1) Press the [
2) Enter your [
3) Enter the desired [
4) Press the [0] key six times to clear the serial number.
6.1.3 P
ROGRAMMING THE
The zones allocated to the wireless transmitters must be programmed. Refer to Zone Programming on page 16 for
more information.
6 . 2 V I E W I N G T H E W I R E L E S S T R A N S M I T T E R S I G N A L S T R E N G T H
S e c t i o n s [ 6 3 1 ] t o [ 6 3 8 ]
Once wireless transmitters have been installed and assigned to the Spectra 1759EX, the signal strength of each transmitter can
be verified in sections [631] to [638]. Each section represents the signal strength viewer for a specific device. For example,
section [631] is the viewer for the device in section [601] and section [638] is the viewer for the device in section [608]. Please
note that this feature only works with wireless transmitters assigned to an Expansion Input (zone) as described in section 6.1.1 on
page 22. A reading of 1 is the weakest and a reading of 8 is the strongest. An average reading of 3 and up is acceptable.
Sometimes moving the transmitter or control panel by a small amount will greatly increase the signal reception.
How Do I View a Wireless Transmitter's Signal Strength?
1) Press the [
ENTER
2) Enter your [
3) Enter the desired [
4) Press the transmitter's tamper switch or open the corresponding zone.
5) On an LED keypad: The keypad will illuminate numbers 1 to 8.
On an LCD keypad: The keypad will display numbers from 1 to 8 on the screen. For example, the LCD screen below
shows a signal strength reading of 5.
After entering the desired section, ignore the first reading as it will not be accurate.
You can also use a beep sequence feature to verify a transmitter's signal strength. When you press a transmitter's tamper switch,
beep tones emanating from all the keypads connected to the communication bus will advise you of the transmitter's signal
strength.
How Do I Attain a Wireless Transmitter's Signal Strength using the Beep Sequence?
1) Press the [
ENTER
2) Enter your [
3) Enter the desired [
4) Press the transmitter's tamper switch or open the corresponding zone.
5) Listen for the beep tones:
If the signal strength is less than 3 = One beep
If the signal strength is between 3 and 6 = Two beeps
If the signal strength is greater than 6 = Three beeps
This feature cannot be used with any remote controls assigned to the control panel.
6 . 3 S E R I A L N U M B E R D I S P L A Y
S e c t i o n [ 6 3 0 ]
This feature will display the serial number of any wireless transmitter on any Spectra keypad.
How Do I View a Transmitter's Serial Number?
1) Press the [
ENTER
2) Enter your [
3) Enter the section [630].
4) Press the [0] key six times to clear the serial number.
A W
SSIGNED IRELESS
] key.
ENTER
].
INSTALLER CODE
SECTION NUMBER
Z
ONES
] key.
].
INSTALLER CODE
] (from sections [631] to [638]).
SECTION NUMBER
] key.
].
INSTALLER CODE
] (from sections [631] to [638]).
SECTION NUMBER
] key.
].
INSTALLER CODE
T
RANSMITTERS
] (from sections [601] to [608]).
2 3
P E C T R A
S 1 7 5 9 E X