Event Call Direction; Dialing Method; Pulse Ratio; Bell On Communication Failure - Paradox Spectra 1759EX V1.0 Reference & Installation Manual

E V E N T C A L L D I R E C T I O N
Section [137]
Option [1] ON = Call Telephone #1 for
Option [2] ON = Call Telephone #2 for
Option [3] ON = Call Telephone #1 for
Option [4] ON = Call Telephone #2 for
Option [5] ON = Call Telephone #1 for
Option [6] ON = Call Telephone #2 for
Section [138]
Option [1] ON = Call Telephone #1 for
Option [2] ON = Call Telephone #2 for
Option [3] ON = Call Telephone #1 for
Option [4] ON = Call Telephone #2 for
This feature determines where each group of events will be reported. The control panel events are divided into five groups (see
above) where each event group can be programmed to dial one or both Central Station Telephone Numbers. When a reportable
event occurs in the system, the control panel will verify that one of the two telephone numbers has been enabled. The control
panel will begin by dialing the selected telephone number(s). If both numbers were selected it will begin with Central Station
Telephone Number 1. After the Maximum Dialing Attempts (see page 37) to one central station telephone number have failed, the
control panel will then dial the backup telephone number. If the Alternate Dial Option (see page 38) is enabled, the control panel
will dial the programmed backup telephone number after every failed attempt. If no backup telephone number is programmed,
the control panel will never report to the backup telephone number. Also, refer to Delay Between Dialing Attempts on page 38.
Example: The system is armed and zone 1 has been breached causing an alarm. If option [3] is off and option [4] is on in section
[137], the control panel will attempt to communicate with Central Station Telephone Number 2 in order to transmit the Zone 1
Alarm Report Code programmed in section [187].
D I A L I N G M E T H O D
S e c t i o n [ 1 3 5 ] : D i a l e r O p t i o n s
O p t i o n O F F = P u l s e D i a l i n g . ( A l s o , r e f e r t o P u l s e R a t i o , b e l o w )
[ 4 ]
O p t i o n O N = T o n e / D T M F D i a l i n g ( d e f a u l t )
[ 4 ]
P U L S E R A T I O
S e c t i o n [ 1 3 5 ] : D i a l e r O p t i o n s
O p t i o n O F F = E u r o p e a n P u l s e R a t i o o f 1 : 2
[ 5 ]
O p t i o n O N = U . S . A . P u l s e R a t i o o f 1 : 1 . 5 ( d e f a u l t )
[ 5 ]
When using Pulse dialing, you can select one of two Pulse Ratios. Although most European countries use the 1:2 pulse ratio, the
1:1.5 ratio may provide better results in some cases. The same applies for North American countries. If the 1:1.5 pulse ratio is not
providing the desired results, the 1:2 ratio may be used.
S e c t i o n [ 1 3 5 ] : D i a l e r O p t i o n s
O p t i o n O F F = B e l l O n C o m m u n i c a t i o n F a i l u r e D i s a b l e d ( d e f a u l t )
[ 6 ]
O p t i o n O N = B e l l O n C o m m u n i c a t i o n F a i l u r e E n a b l e d
[ 6 ]
If the control panel fails to communicate with the central station when the system is armed, it will enable the
off any bells or sirens connected to the output.
S e c t i o n [ 1 3 6 ] : D i a l e r O p t i o n s
O p t i o n O F F = D i a l e r w i l l c o n t i n u e t o d i a l i f n o d i a l t o n e i s p r e s e n t a f t e r 4 s e c o n d s ( d e f a u l t ) .
[ 5 ]
O p t i o n O N = D i a l e r w i l l h a n g - u p i f n o d i a l t o n e i s p r e s e n t a f t e r 1 6 s e c o n d s
[ 5 ]
S e c t i o n [ 0 8 1 ]
001 to 016 attempts, Default = 8 attempts
The value programmed in section [081] determines how many times the control panel will re-dial the same Central Station
Telephone Number before proceeding to the next number.
Arm/Disarm Report Codes in sections [160] to [186] (page 33)
Alarm/Restore Report Codes in sections [187] to [196] (pages 33 to 34)
Tamper/Restore Report Codes in sections [197] to [204] (page 34)
Trouble/Restore Report Codes in sections [205] to [210] (pages 34 to 35)
Special Report Codes in sections [211] to [213] (page 35)
output, setting
BELL
3 7
P E C T R A
S 1 7 5 9 E X