One-Touch Arming; Keyswitch Arming; Panic Alarms - Paradox Spectra 1759EX V1.0 Reference & Installation Manual

How do I Program Bypass Entries?
1) Press the [
BYP
2) Key in a valid [
3) Select one or more [
4) Once you have entered the desired bypass entries, press the [
*IF YOU HAVE ACCESS TO BOTH PARTITIONS:
Press the key corresponding to the desired partition.
13.8.1 B
YPASS
After disarming the system, the control panel will erase the bypass entries. By using the Bypass Recall Feature, you
can reinstate the previous bypass entries saved in memory. This eliminates the need to manually program the bypass
entries every time you arm the system. The Access Code must have the Bypass Programming Option enabled.
How Do I Recall Bypass Entries?
1) Press the [
2) Key in your [
3) Press the [
4) Press the [
*IF YOU HAVE ACCESS TO BOTH PARTITIONS:
Press the key corresponding to the desired partition.
1 3 . 9 O N E - T O U C H A R M I N G
One-Touch Arming allows users to arm the system without using an access code. Simply press and hold a key. One-Touch
Arming can be used to allow specific individuals like service personnel (i.e. cleaners, maintenance) to arm the system when
leaving the protected area, without giving them access to any other alarm system operations.
One-Touch Regular Arming
Press and hold the [
One-Touch Force Arming
Press and hold the [
One-Touch Bypass Programming
Press and hold the [
One-Touch Stay Arming
Press and hold the [
Fast Exit - When the system is already Stay Armed:
• To Exit and Stay Arm: Press and hold the [
period, the system will return to Stay Arming.
• To Exit and Regular Arm: Press and hold the [
Delay period, the control panel will switch to Regular Arming.
• To Exit and Force Arm: Press and hold the [
Delay period, the control panel will switch to Force Arming.
* If you have access to both partitions after activating a one-touch feature, press the key corresponding to the desired partition.
To select both partitions, press the [1] key then after the confirmation beep press the [2] key.
1 3 . 1 0 K E Y S W I T C H A R M I N G
A keyswitch can be used to arm and disarm the system. Assign the keyswitch to a specific partition and program the keyswitch to
Stay or Regular Arm the assigned partition. Also program the keyswitch to function as a Maintained or Momentary keyswitch. To
arm the system using a Maintained Keyswitch, set the keyswitch to the
position. To arm the system using a Momentary Keyswitch, set the keyswitch to the
OFF
position. Repeating this sequence will disarm the system.
1 3 . 1 1 P A N I C A L A R M S
In case of emergency, the Spectra system provides up to three panic alarms. These panic alarms, if programmed, will immediately
generate an alarm after pressing and holding two specific keys for two seconds, as described below.
Press and hold keys [1] and [3] for a panic alarm.
Press and hold keys [4] and [6] for a panic or medical alarm.
Press and hold keys [7] and [9] for a panic or fire alarm.
R & I
5 0 EFERENCE NSTALLATION
] key.
]*.
ACCESS CODE
] you wish to bypass.
ZONES
R F
ECALL EATURE
] key.
BYP
]*.
ACCESS CODE
] key. Previously bypassed zones will illuminate.
BYP
] key.
ENTER
] key for 3 seconds* to arm all zones in the partition.
ENTER
] key for 3 seconds* to bypass any open Force Zones.
FORCE
] key for 3 seconds* to access Bypass Programming Mode.
BYP
] key for 3 seconds* to arm all zones not defined as Stay Zones.
STAY
STAY
FORCE
M
ANUAL
] key to accept these entries.
ENTER
] key for 3 seconds*. The system will switch to Exit Delay. At the end of the Exit Delay
] key for 3 seconds*. The system will switch to Exit Delay. At the end of the Exit
ENTER
] key for 3 seconds*. The system will switch to Exit Delay. At the end of the Exit
ON
position. To disarm the system set the keyswitch to the
position then turn it back to the
ON OFF