Cebora EVO SPEED STAR 380 TC Instruction Manual page 158

1 FÖRSIKTIGHETSÅTGÄRDER .......................................................................................................................................................159
1.1 VARNINGSSKYLT ..................................................................................................................................................................159
2 ALLMÄN BESKRIVNING ..............................................................................................................................................................160
2.1 FÖRKLARING AV TEKNISKA DATA ..................................................................................................................................160
3 INSTALLATION OCH DRIFTFÖRBEREDELSER .......................................................................................................................160
3.1 LYFT
3.2 MONTAGE ................................................................................................................................................................................160
3.3 ANSLUTNING AV EVENTUELLA FÖRLÄNGNINGS- KABLAR ................................................................................... 161
3.4 ANSLUTNING AV SVETSBRÄNNAREN ............................................................................................................................162
3.5 MONTAGE AV KYLENHET ...................................................................................................................................................162
3.6 PLACERING .............................................................................................................................................................................162
3.6.1 LUTANDE PLAN ..........................................................................................................................................................162
3.7 DRIFTFÖRBEREDELSER ......................................................................................................................................................162
4 BESKRIVNING AV GENERATOR .................................................................................................................................................163
5 BESKRIVNING AV KYLENHET ART 1683 .................................................................................................................................165
5.1 ANSLUTNINGAR. ...................................................................................................................................................................165
5.2 BESKRIVNING AV SKYDD ...................................................................................................................................................165
5.2.1 SKYDDSANORDNING TRYCK KYLVÄTSKA .........................................................................................................165
5.2.2 SÄKRING (T 2A/250V-Ø 5X20) ..................................................................................................................................165
5.3 DRIFTFÖRBEREDELSER ......................................................................................................................................................165
6 BESKRIVNING AV KONTROLLPANEL .......................................................................................................................................165
6.1 KONTROLLPANEL ..................................................................................................................................................................165
6.2 INSTÄLLNINGSPANEL ..........................................................................................................................................................167
6.3 VISNING AV ALARM .............................................................................................................................................................168
6.4 VISNING AV FEL .....................................................................................................................................................................168
7 MASKINPROGRAMMERING "MAIN MENU" - "HUVUDMENY" ........................................................................................168
7.1 MENU "PROCESS PARAMS" - "PROCESSPARAMETRAR" ............................................................................................169
7.1.1 "PROCESS" ....................................................................................................................................................................169
7.1.2 "MATERIAL" ................................................................................................................................................................169
7.1.3 "DIAMETER" ................................................................................................................................................................169
7.1.4 "GAS" .............................................................................................................................................................................169
7.1.5 "ARCLENGTHCORR"- "KORREKTION BÅGLÄNGD" ...........................................................................................169
7.1.6 "INDUCTANCECORR"- "KORREKTION IMPEDANSVÄRDE" ............................................................................169
7.1.7 "START MODE"- "STARTSÄTT" ................................................................................................................................169
7.1.8 "SPOT" - "PUNKTSVETSNING / INTERMITTENS" ...............................................................................................169
7.1.9 "HSA"- "HOT START AUTOMATISK" ......................................................................................................................170
7.1.10 "CRA"- "FYLLNING AV ÄNDKRATER" ..................................................................................................................170
7.1.11 "SOFT START"- "MJUKSTART" ................................................................................................................................170
7.1.12 "BURNBACK" ...............................................................................................................................................................170
7.1.13 "DOUBLE LEVEL"- "DUBBEL NIVÅ" .......................................................................................................................170
7.1.13.1 "FREQUENCY"- "FREKVENS" FÖR DUBBEL NIVÅ ................................................................................170
7.1.13.2 "PULSESTEP": ÄR OMFATTNINGEN FÖR HASTIGHETSÄNDRINGEN I M/MIN ..............................170
7.1.13.3 "DUTY CYCLE": TID FÖR DUBBEL NIVÅ ................................................................................................170
7.1.13.4 "ARCLENGTHCOR" -"KORREKTION AV BÅGLÄNGDEN" .....................................................................170
7.1.14 "DOUBLE PULSE" - DUBBEL PULSERING. ............................................................................................................171
7.1.15 "PREFOW"- "PRE GAS" ...............................................................................................................................................171
7.1.16 "POSTFLOW"- "POST GAS" .......................................................................................................................................171
7.1.17 "SPEEDCORR"- "KORREKTION AV HASTIGHETEN" ..........................................................................................171
7.2 MENY "JOB" ............................................................................................................................................................................171
7.2.1 MEMORERA ETT PROGRAM "JOB" ........................................................................................................................171
7.3 MENY "SETTINGS" - "INSTÄLLNINGAR" ........................................................................................................................171
7.3.1 MENY "WELDING" - "SVETSNING" .......................................................................................................................171
7.3.2 MENY "MACHINE"- "MASKININSTÄLLNINGAR". .............................................................................................171
7.3.3 MENY "FACTORY SETUP" - "ÅTERSTÄLLNING STANDARDINSTÄLLNINGAR" .........................................171
7.3.4 MENY "LANGUAGES"- "SPRÅKINSTÄLLNINGAR" ............................................................................................172
7.4 MENY INFORMATION ..........................................................................................................................................................172
8 SNABBTILLTRÄDE .........................................................................................................................................................................172
8.1 "MEM" - "MEMORERING" ....................................................................................................................................................172
8.2 "PAR" - "PROCESSPARAMETRAR" .....................................................................................................................................172
8.3 "2T/4T" - "TVÅTAKTS / FYRTAKTS" ...................................................................................................................................172
8.4 "JOB"- "ARBETSPROGRAM" ................................................................................................................................................172
8.5 "H2O"
8.6 "WIZ" WIZARD .......................................................................................................................................................................172
9 SVETSNING
9.1 MIG/MAG-SVETSNING .........................................................................................................................................................172
9.1.1 MIG ---- SYNERGISK MIG/MAG-SVETSNING ......................................................................................................172
9.1.2 MIG MAN. KONVENTIONELL MIG/MAG-SVETSNING ......................................................................................172
9.1.3 MIG MAN. SYNERGISK MIG/MAG-SVETSNING SVETSGODS MED HÖG HÅLLFASTHET ........................172
9.1.4 MIG ROOT SYNERGISK MIG/MAG-SVETSNING. .................................................................................................173
9.1.5 MIG
9.2 MMA-SVETSNING ..................................................................................................................................................................173
9.3 TIG-SVETSNING .....................................................................................................................................................................173
9.3.1 MASKINER MED SEPARAT TRÅDMATNING .......................................................................................................173
9.3.2 KOMPAKTA MASKINER ............................................................................................................................................173
10 FELKODER
11 UNDERHÅLL
11.1 UNDERHÅLL GENERATOR ................................................................................................................................................. 175
11.2 ÅTGÄRDER SOM BÖR VIDTAS EFTER REPARATION ................................................................................................... 175
158
................................................................................................................................................................................160
................................................................................................................................................................................172
................................................................................................................................................................................172
PULSERANDE SYNERGISK MIG/MAG-SVETSNING ......................................................................173
................................................................................................................................................................................ 174
................................................................................................................................................................................ 175
INDEXERA