Emerson Rosemount 3051P Reference Manual
  1. Manuals
  2. Brands
  3. Emerson Manuals
  4. Transmitter
  5. Rosemount 3051P
  6. Reference manual
Emerson Rosemount 3051P Reference Manual

Emerson Rosemount 3051P Reference Manual

In-line pressure, with hart protocol
Hide thumbs Also See for Rosemount 3051P:
Table of Contents

Advertisement

Quick Links

Download this manual
Reference Manual
00809-0700-4001, Rev AA
May 2017
™
Rosemount
3051P In-Line Pressure Transmitter
®
with HART
Protocol

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Rosemount 3051P and is the answer not in the manual?

Questions and answers

Related Manuals for Emerson Rosemount 3051P

Summary of Contents for Emerson Rosemount 3051P

  • Page 1 Reference Manual 00809-0700-4001, Rev AA May 2017 ™ Rosemount 3051P In-Line Pressure Transmitter ® with HART Protocol...

  • Page 3: Table Of Contents

    Models covered ..............1 1.2.1 Rosemount 3051P In-Line Gage Pressure Transmitter ......1 1.2.2 Rosemount 3051P In-Line Absolute Pressure Transmitter .
  • Page 4 Contents Reference Manual 00809-0700-4001, Rev AA May 2017 2.11.3 Simulate device variables........... . 22 2.12 Configuring burst mode .
  • Page 5 7.1.1 Rosemount 3051P safety certified identification ....... . 65 Contents...
  • Page 6 Configuring in SIS applications ..........65 7.1.4 Rosemount 3051P SIS operation and mainenance ......66 7.1.5 Inspection .
  • Page 7 Reference Manual Contents 00809-0700-4001, Rev AA May 2017 Options ............... . . 79 A.6.1 Standard configuration .
  • Page 8 Contents Reference Manual 00809-0700-4001, Rev AA May 2017 Contents...
  • Page 9 The products described in this document are NOT designed for nuclear-qualified applications. Using non-nuclear qualified products in applications that require nuclear-qualified hardware or products may cause inaccurate readings. For information on Rosemount nuclear-qualified products, contact your local Emerson Sales Representative. Title Page...
  • Page 10 Installation of this transmitter in an explosive environment must be in accordance with the appropriate local, national, and international standards, codes, and practices. Review the approvals section of the Rosemount 3051P Reference Manual for any restrictions associated with a safe installation.

  • Page 11: Using This Manual

    ™ Rosemount 3051P. The sections are organized as follows: Section 2: Configuration provides instruction on commissioning and operating Rosemount 3051P Transmitters. Information on software functions, configuration parameters, and online variables is also included. Section 3: Hardware Installation contains mechanical installation instructions, and field upgrade options.
  • Page 12 Introduction Reference Manual 00809-0700-4001, Rev AA May 2017 Introduction...

  • Page 13: Safety Messages

    Reference Manual Configuration 00809-0700-4001, Rev AA May 2017 Section 2 Configuration Safety messages ..............page 3 System readiness .

  • Page 14: System Readiness

    Installation of this transmitter in an explosive environment must be in accordance with the appropriate local, national, and international standards, codes, and practices. Review the approvals section of the Rosemount 3051P Reference Manual for any restrictions associated with a safe installation.
  • Page 15 Reference Manual Configuration 00809-0700-4001, Rev AA May 2017 Table 2-1. Device Revisions and Files Review Identify device Find device driver files Review instructions functionality Software NAMUR NAMUR HART HART release hardware software software universal Device Manual document Changes to date revision revision revision...

  • Page 16: Hart Installation Flowchart

    Configuration Reference Manual 00809-0700-4001, Rev AA May 2017 HART installation flowchart Figure 2-1. HART Installation Flowchart START HERE Bench Calibration? Field Install Configure Security and Configure for Alarm Verify Pressure (page Mount Transmitter Set Units Review Transmitter page 29 Configuration page 12 page 9 Check Process...

  • Page 17: Transmitter Overview

    The Rosemount 3051P utilizes piezoresistive sensor technology for AP and GP measurements. The major components of the Rosemount 3051P In-Line are the sensor module and the electronics housing. The sensor module contains the oil filled sensor system (isolating diaphragm, oil fill system and sensor).
  • Page 18 Configuration Reference Manual 00809-0700-4001, Rev AA May 2017 Figure 2-3. Block Diagram Of Operation Signal Processing Microprocessor Digital-to- • Sensor Module Sensor linearization Analog Signal Temp. • Rerange Memory Conversion • Sensor Damping • Diagnostics • Engineering units Digital • Communication Pressure Communication...

  • Page 19: Configuration Overview

    Set all transmitter hardware adjustments during commissioning to avoid exposing the transmitter electronics to the plant environment after installation. The Rosemount 3051P can be configured either before or after installation. Configuring the transmitter on the bench using either a Field Communicator, AMS Device Manager, or LOI ensures all transmitter components are in working order prior to installation.

  • Page 20: Configuration Tools

    Device Dashboard interface. As stated in System readiness , it is critical that the latest DD’s are loaded into the Field Communicator. Visit Emerson.com FieldCommGroup.org to download latest DD library. Field Communicator menu trees and Fast Keys are available in...

  • Page 21: Setting The Loop To Manual

    Field Communicator are located in Appendix C: Field Communicator Menu Trees and Fast Keys. Fast key sequences for the latest DD are shown in Table 2-3. For Fast Key sequences for legacy DD's contact your local Emerson Representative. Configuration...

  • Page 22: Verifying Configuration With Ams Device Manager

    Reference Manual Configuration 00809-0700-4001, Rev AA May 2017 Table 2-3. Device Dashboard Fast Key Sequence From the HOME screen, enter the Fast Key sequences listed Fast Key sequence Function HART 7 HART 5 Alarm and Saturation Levels 2, 2, 2, 5 2, 2, 2, 5 Damping 2, 2, 1, 1, 5...

  • Page 23: Rerange The Transmitter

    Reference Manual Configuration 00809-0700-4001, Rev AA May 2017 Setting pressure units with a Field Communicator From the HOME screen, enter the Fast Key sequence 2, 2, 1, 1, 4 Device Dashboard Fast Keys Setting pressure units with AMS Device Manager 1.
  • Page 24 Configuration Reference Manual 00809-0700-4001, Rev AA May 2017 Manually rerange the transmitter by entering range points Entering range points with a Field Communicator From the HOME screen, enter the Fast Key sequence Device Dashboard Fast Keys 2, 2, 2, 1 Entering range points with AMS Device Manager 1.
  • Page 25 Reference Manual Configuration 00809-0700-4001, Rev AA May 2017 Figure 2-9. Rerange with Applied Pressure Using LOI RERANGE VIEW CONFIG ENTER VALUES ZERO TRIM APPLY VALUES APPLY VALUES APPLY VALUES UNITS RERANGE RERANGE BACK TO MENU EXIT MENU LOOP TEST BACK TO MENU DISPLAY EXIT MENU EXTENDED MENU...

  • Page 26: Damping

    Configuration Reference Manual 00809-0700-4001, Rev AA May 2017 Note If the transmitter security is on, adjustments to the zero and span will not be able to be made. Refer to  “Configuring transmitter security” on page 36 for security information. The span is maintained when the 4 mA/1 V point is set.

  • Page 27: Configuring The Lcd Display

    Reference Manual Configuration 00809-0700-4001, Rev AA May 2017 Configuring the LCD display The LCD display configuration command allows customization of the LCD display to suit application requirements. The LCD display will alternate between the selected items. Pressure Units Sensor Temperature ...
  • Page 28 Configuration Reference Manual 00809-0700-4001, Rev AA May 2017 Table 2-4. Rosemount Alarm and Saturation Values Level 4–20 mA saturation 4–20 mA alarm ≤ 3.75 mA 3.90 mA ≥ 21.75 mA High 20.80 mA Table 2-5. NAMUR-Compliant Alarm and Saturation Values Level 4–20 mA saturation 4–20 mA alarm...

  • Page 29: Configuring Scaled Variable

    Reference Manual Configuration 00809-0700-4001, Rev AA May 2017 Figure 2-13. Configuring Alarm and Saturation with LOI EXTENDED MENU VIEW CONFIG CALIBRAT ZERO TRIM DAMPING UNITS TRANSFER FUNCT RERANGE SCALED VARIAB LOOP TEST ASSIGN PV DISPLAY EXTENDED MENU EXTENDED MENU ALARM SAT VALUES ALARM SAT VALUES ALARM SAT VALUES ROSEMOUNT VALUES...

  • Page 30: Re-Mapping Device Variables

    Configuration Reference Manual 00809-0700-4001, Rev AA May 2017 Figure 2-14. Configuring Scaled Variable Using a LOI EXTENDED MENU VIEW CONFIG CALIBRAT ZERO TRIM DAMPING UNITS SCALED VARIAB TRANSFER FUNCT RERANGE SCALED VARIAB SCALED VARIAB VIEW SCALED LOOP TEST CONFIG SCALED CONFIG SCALED ASSIGN PV DISPLAY...

  • Page 31: Performing Transmitter Tests

    Reference Manual Configuration 00809-0700-4001, Rev AA May 2017 Figure 2-15. Re-mapping with Local Operator Interface VIEW CONFIG EXTENDED MENU ZERO TRIM CALIBRAT UNITS DAMPING RERANGE TRANSFER FUNCT LOOP TEST SCALED VARIAB ASSIGN PV DISPLAY EXTENDED MENU EXIT MENU ALARM SAT VALUES PASSWORD SIMULATE HART REV...

  • Page 32: Simulate Device Variables

    Configuration Reference Manual 00809-0700-4001, Rev AA May 2017 Using an analog loop test using AMS Device Manager 1. Right click on the device and, within the Methods drop down menu, move cursor over Diagnostics and Test. In the Diagnostics and Test drop down menu select Loop Test. 2.

  • Page 33: Configuring Burst Mode

    Reference Manual Configuration 00809-0700-4001, Rev AA May 2017 2.12 Configuring burst mode Burst mode is compatible with the analog signal. Because the HART protocol features simultaneous digital and analog data transmission, the analog value can drive other equipment in the loop while the control system is receiving the digital information.

  • Page 34: Establishing Multidrop Communication

    A. HART modem B. Power supply The Rosemount 3051P is set to address zero (0) at the factory, which allows operation in the standard point-to-point manner with a 4–20 mA output signal. To activate multidrop communication, the transmitter address must be changed to a number from 1 to 15 for HART Revision 5, or 1–63 for HART Revision 7.

  • Page 35: Changing A Transmitter Address

    Reference Manual Configuration 00809-0700-4001, Rev AA May 2017 2.13.1 Changing a transmitter address To activate multidrop communication, the transmitter poll address must be assigned a number from 1 to 15 for HART Revision 5, and 1–63 for HART Revision 7. Each transmitter in a multidropped loop must have a unique poll address.
  • Page 36 Reference Manual Configuration 00809-0700-4001, Rev AA May 2017 Configuration...

  • Page 37: Overview

    Hardware Installation Reference Manual May 2017 00809-0100-4108, Rev CA Section 3 Hardware Installation Overview ................page 27 Safety messages .

  • Page 38: Considerations

    Installation of this transmitter in an explosive environment must be in accordance with the appropriate local, national, and international standards, codes, and practices. Review the approvals section of the Rosemount 3051P Reference Manual for any restrictions associated with a safe installation.

  • Page 39: Environmental Considerations

    Protection ratings are required. For M20 threads, install conduit plugs to full thread engagement or until mechanical resistance is met. Mounting brackets Rosemount 3051P Transmitters may be panel-mounted or pipe-mounted via an optional mounting bracket (option code B4). See Figure 3-1 and for dimensional and mounting configuration information.
  • Page 40 Hardware Installation Reference Manual 00809-0100-4108, Rev CA May 2017 Figure 3-1. Mounting Bracket Option Code B4 Pipe mounting Panel mounting 5.13 (130) 3.85 (98) 4.26 (109) 3.95 (100) 6.15 (156) 2.81 (71) 2.97 (75) 5.97 (1.52) 4.78 (121) 2-in. U-Bolt for pipe mounting 6.90 (175) (clamp shown)

  • Page 41: Impulse Piping

    Reference Manual Hardware Installation 00809-0100-4108, Rev CA May 2017 3.4.2 Impulse piping Mounting requirements Impulse piping configurations depend on specific measurement conditions. Refer to Figure 3-3 on page 31 through Figure 3-5 on page 32 for examples of the following mounting configurations: Liquid measurement Place taps to the side of the line to prevent sediment deposits on the transmitter’s process isolator.
  • Page 42 Hardware Installation Reference Manual 00809-0100-4108, Rev CA May 2017 Figure 3-4. Gas Applications Installation Example Figure 3-5. Steam Applications Installation Example Best practices The piping between the process and the transmitter must accurately transfer the pressure to obtain accurate measurements. There are five possible sources of error: pressure transfer, leaks, friction loss (particularly if purging is used), trapped gas in a liquid line, liquid in a gas line, and density variations between the legs.

  • Page 43: Inline Process Connection

    Reference Manual Hardware Installation 00809-0100-4108, Rev CA May 2017 Vent all gas from liquid piping legs.  When purging, make the purge connection close to the process taps and purge through equal lengths  of the same size pipe. Avoid purging through the transmitter. Keep corrosive or hot (above 250 °F [121 °C]) process material out of direct contact with the sensor ...

  • Page 44: Rosemount 306 Manifold

    00809-0100-4108, Rev CA May 2017 Rosemount 306 Manifold The Rosemount 306 Integral Manifold is used with the Rosemount 3051P In-Line Transmitter to provide block-and-bleed valve capabilities of up to 10000 psi (690 bar). Figure 3-7. Rosemount 3051P and 306 In-line Manifold 3.5.1...

  • Page 45: Overview

    Installation of this transmitter in an explosive environment must be in accordance with the appropriate local, national, and international standards, codes, and practices. Review the approvals section of the Rosemount 3051P Reference Manual for any restrictions associated with a safe installation. In an Explosion-Proof/Flameproof installation, do not remove the transmitter covers when power is ...

  • Page 46: Local Operating Interface (Loi)/Lcd Display

    5. Reattach transmitter housing cover; cover must be fully engaged to comply with explosion proof requirements. 6. Re-attach power and return loop to automatic control. Configuring transmitter security There are four security methods with the Rosemount 3051P Transmitters. Security switch  ®...

  • Page 47: Setting Security Switch

    Reference Manual Electrical Installations 00809-0700-4001, Rev AA May 2017 Figure 4-2. 4–20 mA Electronics Board Without LCD display meter With LCD display /LOI display A. Alarm B. Security 4.4.1 Setting security switch The security switch is used to prevent changes to the transmitter configuration data. If the security switch is set to the locked location ( ), any transmitter configuration requests sent via HART, LOI, or local configuration buttons will be rejected by the transmitter and the transmitter configuration data will...

  • Page 48: Configuration Button Lock

    Electrical Installations Reference Manual 00809-0700-4001, Rev AA May 2017 Configuring HART lock using Field Communicator From the HOME screen, enter the Fast Key sequence Device Dashboard Fast Keys 2, 2, 6, 4 Configuring HART lock using AMS Device Manager 1. Right click the device and select Configure. 2.

  • Page 49: Setting Transmitter Alarm

    Reference Manual Electrical Installations 00809-0700-4001, Rev AA May 2017 Configuring password with AMS Device Manager 1. Right click the device and select Configure. 2. Under Manual Setup select the Security tab. 3. Within the LOI select the Configure Password button and follow the screen prompts. Configuring LOI password using LOI Figure 4-3.

  • Page 50: Conduit Installation

    Electrical Installations Reference Manual 00809-0700-4001, Rev AA May 2017 4.6.1 Conduit installation If all connections are not sealed, excess moisture accumulation can damage the transmitter. Make sure to mount the transmitter with the electrical housing positioned downward for drainage. To avoid moisture accumulation in the housing, install wiring with a drip loop, and ensure the bottom of the drip loop is mounted lower than the conduit connections of the transmitter housing.

  • Page 51: Wiring The Transmitter

    Reference Manual Electrical Installations 00809-0700-4001, Rev AA May 2017 Figure 4-5. Load Limitation Maximum loop resistance = 43.5 x (Power supply voltage – 10.5) 1387 1000 Operating Region 10.5 42.4 Ω The Field Communicator requires a minimum loop resistance of 250 for communication.

  • Page 52: Grounding The Transmitter

    Electrical Installations Reference Manual 00809-0700-4001, Rev AA May 2017 2. For 4–20 mA HART output, connect the positive lead to the terminal marked (pwr/comm+) and the negative lead to the terminal marked (pwr/comm–). Do not connect the powered signal wiring to the test terminals.

  • Page 53: Transient Protection Terminal Block Grounding

    The transient protection terminal block can be ordered as an installed option (Option Code T1) or as a spare part to retrofit existing Rosemount 3051P Transmitters in the field. See “Ordering information” on page 74 for part numbers.
  • Page 54 Electrical Installations Reference Manual 00809-0700-4001, Rev AA May 2017 Figure 4-9. Transient Protection Terminal Block A. Lightning bolt location Note The transient protection terminal block does not provide transient protection unless the transmitter case is properly grounded. Use the guidelines to ground the transmitter case. Refer to Figure 4-8 on page Electrical Installations...

  • Page 55: Overview

    Operation and Maintenance Reference Manual May 2017 00809-0700-4001, Rev AA Section 5 Operation and Maintenance Overview ................page 45 Safety messages .

  • Page 56: Recommended Calibration Tasks

    Operation and Maintenance Reference Manual 00809-0700-4001, Rev AA May 2017 Recommended calibration tasks Absolute pressure transmitters are calibrated at the factory. Trimming adjusts the position of the factory characterization curve. It is possible to degrade performance of the transmitter if any trim is done improperly or with inaccurate equipment.

  • Page 57: Determining Necessary Sensor Trims

    Reference Manual Operation and Maintenance 00809-0700-4001, Rev AA May 2017 Calibrate the 4–20 mA output 4–20 mA Output trim (page  4–20 mA Output trim using other scale (page  5.4.1 Determining necessary sensor trims Bench calibrations allow for calibrating the instrument for its desired range of operation. Straight forward connections to pressure source allow for a full calibration at the planned operating points.

  • Page 58: Determining Calibration Frequency

    Step 1: Determine the performance required for your application. Required Performance: 0.50% of span Step 2: Determine the operating conditions. Transmitter: Rosemount 3051P, Range 1 [URL = 30 psi (2,1 bar)] Calibrated Span: 30 psi (2,1 bar) Ambient Temperature Change: ± 50 °F (28 °C) Step 3: Calculate total probable error (TPE).

  • Page 59: Perform A Sensor Trim

    Sensor Trim over the full sensor range. Note Do not perform a zero trim on Rosemount 3051P Absolute Pressure Transmitters. Zero trim is zero based, and absolute pressure transmitters reference absolute zero. To correct mounting position effects on an Absolute Pressure Transmitter, perform a low trim within the sensor trim function. The low trim function provides an offset correction similar to the zero trim function, but it does not require zero-based input.
  • Page 60 Reference Manual Operation and Maintenance 00809-0700-4001, Rev AA May 2017 To calibrate the sensor with a Field Communicator using the sensor trim function, perform the following procedure: 1. Select 2: Lower Sensor Trim. Note Select pressure points so that lower and upper values are equal to or outside the expected process operation range.

  • Page 61: Recall Factory Trim-Sensor Trim

    Reference Manual Operation and Maintenance 00809-0700-4001, Rev AA May 2017 1. Loosen the top tag of the transmitter to expose buttons. 2. Press and hold the digital zero button for at least two seconds, then release to perform a digital zero trim.

  • Page 62: Performing Digital-To-Analog Trim (4-20Ma Output Trim)

    Reference Manual Operation and Maintenance 00809-0700-4001, Rev AA May 2017 Figure 5-5. Analog Output Trim Example A. Before trim B. After Trim 5.6.1 Performing digital-to-analog trim (4–20mA output trim) Note If a resistor is added to the loop, ensure that the power supply is sufficient to power the transmitter to a 20 mA output with additional loop resistance.

  • Page 63: Performing Digital-To-Analog Trim (4-20Ma Output Trim) Using Other Scale

    Reference Manual Operation and Maintenance 00809-0700-4001, Rev AA May 2017 Performing 4–20 mA output trim using local operator interface Figure 5-6. 4–20mA Output Trim using Local Operator Interface EXTENDED MENU VIEW CONFIG CALIBRAT CALIBRAT CALIBRAT ZERO TRIM DAMPING ZERO TRIM UNITS TRANSFER FUNCT LOWER TRIM...

  • Page 64: Switching Hart Revision

    Reference Manual Operation and Maintenance 00809-0700-4001, Rev AA May 2017 Recalling factory trim - analog output with AMS Device Manager 1. Right click the device and, under the Method drop down menu, move cursor over Calibrate and select Restore Factory Calibration. 2.

  • Page 65: Switching Hart Revision With Ams Device Manager

    Reference Manual Operation and Maintenance 00809-0700-4001, Rev AA May 2017 5.7.3 Switching HART revision with AMS Device Manager 1. Select Manual Setup and select HART. 2. Select Change HART Revision, then follow the on screen prompts. Note AMS Device Manager versions 10.5 or greater are compatible with HART Revision 7. 5.7.4 Switching HART revision with LOI Navigate to HART REV within the extended menu and select either HART REV 5 or HART REV 7.
  • Page 66 Reference Manual Operation and Maintenance 00809-0700-4001, Rev AA May 2017 Operation and Maintenance...

  • Page 67: Overview

    Troubleshooting Reference Manual May 2017 00809-0700-4001, Rev AA Section 6 Troubleshooting Overview ................page 57 Safety messages .
  • Page 68 Troubleshooting Reference Manual 00809-0700-4001, Rev AA May 2017 Table 6-1. Rosemount 3051P Troubleshooting for 4–20 mA Output Symptom Corrective actions Transmitter milliamp reading is Verify terminal voltage is 10.5 to 42.4 Vdc at signal terminals zero Check power wires for reversed polarity...

  • Page 69: Diagnostic Messages

    Reference Manual Troubleshooting 00809-0700-4001, Rev AA May 2017 Diagnostic messages Listed in the below sections are detailed table of the possible messages that will appear on either the LCD/LOI display, a Field Communicator, or an AMS Device Manager system. Use the tables below to diagnose particular status messages.
  • Page 70 Troubleshooting Reference Manual 00809-0700-4001, Rev AA May 2017 Table 6-3. Status: Maintenance – Fix Soon Alert name display LOI screen Problem Recommended action screen 1. Check the process and ambient conditions are Sensor The sensor temperature has within –85 to 194 °F (–65 to 90 °C). Temperature exceeded its safe operating TEMP...

  • Page 71: Disassembly Procedures

    4. Remove all electrical leads and disconnect conduit. 5. Remove the transmitter from the process connection. a. The Rosemount 3051P Transmitter is attached to the process by a single hex nut process connection. Loosen the hex nut to separate the transmitter from the process.

  • Page 72: Removing Terminal Block

    6.4.3 Removing the LOI or LCD display Rosemount 3051P with M4 or M5 option codes have and LOI or LCD display. The transmitter LOI/LCD display are located in the compartment opposite the terminal side. To remove and/or replace the LOI/LCD display, perform the following procedures: 1.

  • Page 73: Service Support

    For inquiries outside of the United States, contact the nearest Emerson representative for RMA instructions. To expedite the return process outside of the United States, contact the nearest Emerson representative. Individuals who handle products exposed to a hazardous substance can avoid injury if they are informed of and understand the hazard.
  • Page 74 Reference Manual Troubleshooting 00809-0700-4001, Rev AA May 2017 Troubleshooting...

  • Page 75: Safety Instrumented Systems (Sis) Certification

    Rosemount 3051P SIS operation and maintenance ........

  • Page 76: Rosemount 3051P Sis Operation And Mainenance

    Configuring in SIS applications Use any HART capable configuration tool to communicate with and verify configuration of the Rosemount 3051P. Note Transmitter output is not safety-rated during the following: configuration changes, multidrop, and loop test. Alternative means should be used to ensure process safety during transmitter configuration and maintenance activities.
  • Page 77 Reference Manual Safety Instrumented Systems Requirements 00809-0700-4001, Rev AA May 2017 Rosemount 3051P SIS operation and maintenance 7.5.1 Proof test The following proof tests are recommended. All proof test procedures must be carried out by qualified personnel. “Fast Keys” on page 91 to perform a Loop Test, Analog Output Trim, or Sensor Trim.

  • Page 78: Inspection

    All product repair and part replacement should be performed by qualified personnel. 7.6.4 Rosemount 3051P SIS reference The Rosemount 3051P must be operated in accordance to the functional and performance specifications provided in “Specifications and Reference Data” on page 7.6.5 Failure rate data The FMEDA report includes failure rates.

  • Page 79: Performance Specifications

    Span A.1.3 Dynamic performance Typical HART transmitter response time 4 - 20 mA HART Total Response Time (Td + Tc) Transmitter Output vs. Time Rosemount 3051P: 100 ms Pressure released = Dead time = Time constant Dead Time (Td) 45 ms (nominal)

  • Page 80: Ambient Temperature Effects Per 50 °F (28 °C)

    Reference Manual Specifications and Reference Data May 2017 00809-0700-4001, Rev AA A.1.4 Ambient temperature effects A.2 Functional specifications per 50 °F (28 °C) A.2.1 Service Model Ambient temperature effects Liquid, gas, and vapor applications Ranges ±{0.25 + 0.05(URL/span)}% of span from 1:1 to 10:1 ±{0.125 + 0.07(URL/span)}% of span from 10:1 to A.2.2 Power supply 150:1...

  • Page 81: Overpressure Limits

    Reference Manual May 2017 00809-0700-4001, Rev AA A.2.5 Selectable HART revisions A.2.9 Temperature limits The Rosemount 3051P comes with Selectable HART Ambient Revisions. Digital communications based on HART Revision Sensor fill 5 (option code HR5) or Revision 7 (option code HR7) protocol must be selected.

  • Page 82: Volumetric Displacement

    A. A.3.6 Shipping weights A.3.2 Process connections Without options –14 NPT female The Rosemount 3051P Transmitter weighs 2.4 lb. (1,1 kg) A.3.3 Process-wetted parts With options - 14 NPT female Table A-1. Transmitter Option Weights...

  • Page 83: Dimensional Drawings

    Specifications and Reference Data Reference Manual May 2017 00809-0700-4001, Rev AA Dimensional drawings Figure A-1. Rosemount 3051P 3.85 4.29 (98) 5.13 (109) (130) 4.26 (108) 1.30 (33) A. Digital display cover A. Field terminals C. Transmitter electronics A. Bracket mounting holes ( –20 UNC)

  • Page 84: Ordering Information

    May 2017 00809-0700-4001, Rev AA A.5 Ordering information Table A-2. Rosemount 3051P In-Line Pressure Transmitter Ordering Information ★ The starred offerings ( ) represent the most common options and should be selected for best delivery. The non-starred offerings are subject to additional delivery lead time.
  • Page 85 Reference Manual May 2017 00809-0700-4001, Rev AA Table A-2. Rosemount 3051P In-Line Pressure Transmitter Ordering Information ★ The starred offerings ( ) represent the most common options and should be selected for best delivery. The non-starred offerings are subject to additional delivery lead time.
  • Page 86 Specifications and Reference Data May 2017 00809-0700-4001, Rev AA Table A-2. Rosemount 3051P In-Line Pressure Transmitter Ordering Information ★ The starred offerings ( ) represent the most common options and should be selected for best delivery. The non-starred offerings are subject to additional delivery lead time.
  • Page 87 Reference Manual May 2017 00809-0700-4001, Rev AA Table A-2. Rosemount 3051P In-Line Pressure Transmitter Ordering Information ★ The starred offerings ( ) represent the most common options and should be selected for best delivery. The non-starred offerings are subject to additional delivery lead time.
  • Page 88 Reference Manual Specifications and Reference Data May 2017 00809-0700-4001, Rev AA 11. Configures the HART output to HART Revision 7. The device can be field configured to HART Revision 5 if needed. 12. NACE Compliant wetted materials are identified by Footnote 1.

  • Page 89: Options

    A.6.1 Standard configuration A.6.4 Optional Rosemount 306 Unless otherwise specified, transmitter is shipped as integral manifolds follows: Engineering units Factory assembled to Rosemount 3051P Transmitters. psi (all ranges) Rosemount 306 Product Data Sheet for additional 4 mA 0 (engineering units) information.

  • Page 90: Configuration Buttons

    Reference Manual Specifications and Reference Data May 2017 00809-0700-4001, Rev AA A.6.8 Configuration buttons Rosemount 3051P offers internal and external configuration button options. Choosing option D4 will add external Analog Zero and  Span configuration buttons Choosing option DZ will add an external Digital Trim ...

  • Page 91: European Directive Information

    EU Declaration of Conformity can be found at Standards: CAN/CSA C22.2 No. 0-M91 (R2001), CSA Std C22.2 No. 25-1966, CSA Std C22.2 No. Emerson.com/Rosemount. 30-M1986, CAN/CSA-C22.2 No. 94-M91, CSA Std C22.2 No. 142-M1987, CAN/CSA-C22.2 No. 157-92, CSA Std C22.2 No. 213-M1987, B.2 North America...
  • Page 92 Product Certifications Reference Manual May 2017 00809-0700-4001, Rev AA (process connection) and zone 1 (all other parts of the Special Conditions for Safe Use (X): equipment). The model code and datasheet are to be 1. This apparatus is not capable of withstanding the 500V consulted for details of the diaphragm material.

  • Page 93: International

    Product Certifications Reference Manual May 2017 00809-0700-4001, Rev AA B.4 International Table B-4. Input Parameters E7 IECEx Flameproof HART Parameter Certificate: IECEx KEM 06.0021X Voltage U 30 V Standards: IEC 60079-0:2011, IEC 60079-1:2014, IEC Current I 200 mA 60079-26:2014 Power P 0.9 W Markings: Ex db IIC T6…T4 Ga/Gb T6(–60 °C ≤...

  • Page 94: Technical Regulations Customs Union (Eac)

    Reference Manual Product Certifications May 2017 00809-0700-4001, Rev AA B.5 Technical Regulations Standards: EN60079-0:2012, EN60079-1:2007, IEC60079-7:2007 Customs Union (EAC) Markings: II 2 G Ex d e IIC Gb Table B-5. Conduit Plug Thread Sizes EM EAC Flameproof Thread Identification mark Certificate: TC RU C-US.AA87.B.00534 Markings: Ga/Gb Ex db IIC T5/T6 X, T5(-60 °C ≤...

  • Page 95: Installation Drawings

    Product Certifications Reference Manual May 2017 00809-0700-4001, Rev AA B.8 Installation drawings B.8.1 Installation drawing 02088-1024 PRINTED COPIES ARE UNCONTROLLED Product Certifications...
  • Page 96 Product Certifications Reference Manual May 2017 00809-0700-4001, Rev AA PRINTED COPIES ARE UNCONTROLLED Product Certifications...
  • Page 97 Product Certifications Reference Manual May 2017 00809-0700-4001, Rev AA PRINTED COPIES ARE UNCONTROLLED Product Certifications...
  • Page 98 Product Certifications Reference Manual May 2017 00809-0700-4001, Rev AA Product Certifications...

  • Page 99: Menu Trees

    Field Communicator Menu Trees and Fast Keys Reference Manual May 2017 00809-0700-4001, Rev AA Appendix C Field Communicator Menu Trees and Fast Keys Menu trees ..............page 87 Fast Keys .
  • Page 100 Reference Manual Field Communicator Menu Trees and Fast Keys May 2017 00809-0700-4001, Rev AA Figure C-2. Configure - Guided Setup Device Tagging 1 Tag 2 Long Tag 3 Description 4 Message 5 Date Basic Setup Units of Measure/Damping Units of Measure 1 Device Tagging 1 Units of Measure 1 Pressure...

  • Page 101: Fast Keys

    Field Communicator Menu Trees and Fast Keys Reference Manual May 2017 00809-0700-4001, Rev AA Figure C-3. Configure - Manual Setup Pressure Setup Set Range Points 1 Pressure 1 Primary Variable 2 Upper Range Value 2 Upper Range Value 3 Lower Range Value 3 Lower Range Value 4 Pressure Units 5 Damping...
  • Page 102 Reference Manual Field Communicator Menu Trees and Fast Keys May 2017 00809-0700-4001, Rev AA Figure C-4. Configure - Alert Setup Home 1 Overview 2 Configure Configure 3 Service Tools 1 Guided Setup 2 Manual Setup 3 Alert Setup Pressure Alert Alert Setup 1 Configure Alert 1 Alarm/Saturation...

  • Page 103: Loi Menu Tree

    Field Communicator Menu Trees and Fast Keys Reference Manual May 2017 00809-0700-4001, Rev AA Fast Keys  ) indicates the basic configuration parameters. At minimum these parameters should be verified  as a part of configuration and startup. A (7) indicates availability only in HART revision 7 mode. ...
  • Page 104 Field Communicator Menu Trees and Fast Keys Reference Manual May 2017 00809-0700-4001, Rev AA Field Communicator Menu Trees and Fast Keys...

  • Page 105: Number Entry

    Local Operator Interface Reference Manual May 2017 000809-0700-4001, Rev AA Appendix D Local Operator Interface LOI menu tree ..............page 93 LOI menu tree - extended menu .

  • Page 106: Loi Menu Tree - Extended Menu

    Local Operator Interface Reference Manual May 2017 00809-0700-4001, Rev AA LOI menu tree - extended menu CALIBRAT ZERO TRIM LOWER TRIM UPPER TRIM FACTORY RECALL ANALOG TRIM SENSOR RECALL ANALOG RECALL FACTORY RECALL BACK TO MENU BACK TO MENU EXIT MENU EXIT MENU TRANSFER FUNCT EXTENDED MENU...

  • Page 107: D.3 Number Entry

    Local Operator Interface Reference Manual May 2017 00809-0700-4001, Rev AA Number entry Floating-point numbers can be entered with the LOI. All eight number locations on the top line can be used for number entry. Refer to Table 2-2 on page 11 for LOI button operation.

  • Page 108: Text Entry

    Local Operator Interface Reference Manual May 2017 00809-0700-4001, Rev AA Text entry Text can be entered with the LOI. Depending on the edited item, up to eight locations on the top line can be used for text entry. Text entry follows the same rules as the number entry rules in “LOI menu tree”...
  • Page 110 Terms and Conditions of Enquiries@AP.Emerson.com Sale page. The Emerson logo is a trademark and service mark of Emerson Electric Co. Rosemount and Rosemount logotype are trademarks of Emerson. Middle East and Africa Regional Office DTM is a trademark of the FDT Group.

Table of Contents