Danfoss VLT AutomationDrive FC 300 Operating Instructions Manual page 57

®
VLT AutomationDrive FC 300 Operating
Instructions
Preset ramp bit
Ramp 1
Ramp 2
Ramp 3
Ramp 4
[36] Mains failure inverse
[41] Latched Precise Stop inverse
[55] DigiPot Increase
[56] DigiPot Decrease
[57] DigiPot Clear
[60] Counter A
[61] Counter A
[62] Reset Counter A
[63] Counter B
[64] Counter B
[65] Reset Counter B
[70] Mech. Brake Feedback
[71] Mech. Brake Feedback inv.
[80] PTC Card 1
4.3.3 5-3* Digital Outputs
Parameters for configuring the output functions for the output terminals. The 2 solid-state digital outputs are common for terminals 27 and 29. Set the
I/O function for terminal 27 in par. 5-01
cannot be adjusted while the motor is running.
[0] No operation
[1] Control ready
[2] Drive ready
[3] Drive ready / remote control
[4] Enable / no warning
[5] VLT running
[6] Running / no warning
[7] Run in range / no warning
[8] Run on reference / no warning
[9] Alarm
[10] Alarm or warning
[11] At torque limit
[12] Out of current range
[13] Below current, low
[14] Above current, high
[15] Out of range
[16] Below speed, low
[17] Above speed, high
Activates par. 14-10 Mains Failure
Sends a latched stop signal when the precise stop function is activated in par. 1-83
Function
. The Latched Precise stop inverse function is available for terminals 18 or 19.
INCREASE signal to the Digital Potentiometer function described in parameter group 3-9*
DECREASE signal to the Digital Potentiometer function described in parameter group 3-9*
Clears the Digital Potentiometer reference described in parameter group 3-9*
(Terminal 29 or 33 only) Input for increment counting in the SLC counter.
(Terminal 29 or 33 only) Input for decrement counting in the SLC counter.
Input for reset of counter A.
(Terminal 29 or 33 only) Input for increment counting in the SLC counter.
(Terminal 29 or 33 only) Input for decrement counting in the SLC counter.
Input for reset of counter B.
Brake feedback for hoisting applications
Inverted brake feedback for hoisting applications
All Digital Inputs can be set to PTC Card 1 [80]. However, only one Digital Input must be set to this
choice.
Terminal 27 Mode
, and set the I/O function for terminal 29 in par. 5-02
Default for all digital outputs and relay outputs
The control board receives supply voltage.
The frequency converter is ready for operation and applies a supply signal on the control board.
The frequency converter is ready for operation and is in Auto On mode.
Ready for operation. No start or stop command is been given (start/disable). There are no warnings.
Motor is running.
Output speed is higher than the speed set in par. 1-81
motor is running and there are no warnings.
Motor is running within the programmed current and speed ranges set in par. 4-50
Low to par. 4-53 Warning Speed High
Motor runs at reference speed.
An alarm activates the output. There are no warnings.
An alarm or a warning activates the output.
The torque limit set in par. 4-16
The motor current is outside the range set in par. 4-18
Motor current is lower than set in par. 4-50
Motor current is higher than set in par. 4-51
Output frequency is outside the frequency range set in par. 4-50
Warning Current High
4-51
Output speed is lower than the setting in par. 4-52
Output speed is higher than the setting in par. 4-53
MG.33.AC.02 - VLT is a registered Danfoss trademark
1
0
0
1
1
. Mains failure inverse is active in the Logic .0. situation.
Terminal 29 Mode
Min Speed for Function at Stop [RPM]
. There are no warnings.
Torque Limit Motor Mode
or par. 1-17 has been exceeded.
Current Limit
Warning Current Low
Warning Current High
.
Warning Speed Low
Warning Speed High
4 How to Programme
0
0
1
0
1
Precise Stop
. These parameters
. The
Warning Current
.
.
.
Warning Current Low
and par.
.
.
4
57