Table of Contents
Advertisement
Infotainment settings - Columbus, Amundsen, Bolero
Infotainment system settings
sound settings
›
Tap the
sensor field and then the function surface .
Volume - Volume settings
■
Radio announcements - Volume adjustment of traffic announcements (TP)
■
Navigation announcements - Volume adjustment of navigation announcements
■
(does not apply to infotainment Bolero)
Voice control - volume setting for voice output
■
Maximum switch-on volume - Setting the maximum volume when switching on
■
Infotainment
Speed-dependent Volume adjustment - increases the volume as speed increases
■
Bluetooth audio: - Volume setting of the device connected via Bluetooth
■
dio profile
Quiet - Low volume
■
Medium - Medium volume
■
Loud - High volume
■
Entertainment fading while parking - Lowers the audio volume (e.g. radio volume)
■
when the parking aid is activated
■
Entertainment fading (nav. announcements) - Lowers the audio volume (e.g. radio
volume) in the event of a navigation announcement
Bass - Mid - Treble - Setting the equalizer
■
Balance - Fader - Sets the balance between left and right, front and rear
■
CANTON Equaliser - Setting the equaliser
■
Individual- Adjustment of treble, mid and bass
■
Profile - Setting of the profile (e.g. Rock, Classical and so on.)
■
■
CANTON Optimisation -Setting the optimum room sound perception
All areas - Setting optimised for the whole vehicle interior
■
Front - Setting optimised for the front seats
■
Driver - Setting optimised for the driver
■
CANTON Surround - Setting the surround sound level ("-9 "Stereo / "+9"full sur-
■
round)
Subwoofer - Subwoofer volume settings
■
■
Sound focus -Setting the optimum room sound perception
All areas - Setting optimised for the whole vehicle interior
■
Driver - Setting optimised for the driver
■
Touchscreen tone - Switch on/off audible tone when touching the screen
■
No navigation announcements during calls - Switching on / off the nav. announce-
■
ments during a telephone call (not applicable to Infotainment Bolero)
Display settings
›
Tap the
sensor field and then the function surface → Screen.
Menu: Setting the Infotainment menu display
■
Horizont. Display - Horizontal display
■
■
Grid display - Grid display
Switch off screen (in 10 seconds) - Enable/disable the automatic power off func-
■
tion
Display clock when screen is off - Time and date display when the screen is
■
switched off
Brightness: - Adjusts the brightness of the screen
■
Touchscreen tone - Switch on/off audible tone when touching the screen
■
®
au-
■
Menu button tone - Enable/disable the audible tone when pressing a button next
to the screen (applies to Infotainment Columbus)
Hand gesture - Enable/disable the gesture control using hand movements via
■
the Infotainment screen (applies to Infotainment Columbus)
Visual hand gesture feedback - Enable/disable the animation when a gesture is
■
recognised (applies to Infotainment Columbus)
Audible hand gesture feedback - Enable/disable acoustic signal when a gesture is
■
recognised (applies to Infotainment Columbus)
Animation when finger near screen - Turn the proximity sensors on/off (When the
■
function is on, e.g.Navigation will be shown in the main menu when moving a
finger towards the bottom bar with the function surfaces on the screen)
Show clock in standby mode - Time and date displayed on the screen when the
■
ignition is switched on and Infotainment is switched off
Time and date settings
›
Tap the
sensor field and then the function surface → Time and date.
Clock time source: - Setting the time source: manual/GPS (applies to Infotain-
■
ment Columbus, Amundsen)
Time: - Time settings
■
Summer time - Switches summer time on/off
■
Automatic summer time - Switches the automatic switch to summer time on/off
■
Time zone: - Select the time zone
■
Time format: - Set the time format
■
Infotainment settings - Columbus, Amundsen, Bolero
» Fig. 169
on page 126
» Fig. 168
on page 126
131
Advertisement
Table of Contents
