About Dv - Pioneer DVR-433H-K Operating Instructions Manual

Additional information
14
• Can I use high-speed copy to copy from DVD to HDD?
You can only use high-speed copy from DVD to HDD
when copying Original titles from a VR mode DVD-R
or DVD-RW disc.
See also Copying from DVD to HDD on page 67.
• Can I copy a copy-once protected program from a
subscription satellite or cable channel to a DVD from
the HDD?
Yes, you can use high-speed copy to copy to a VR
mode disc. You can also divide the recording on the
HDD into a number of smaller titles if the whole
recording won't fit on to one disc.
See also Copying from HDD to DVD on page 64.
• Can I play a DVD I recorded on this recorder on another
DVD player?
Yes, you can generally play finalized Video mode
discs recorded on this recorder on any standard DVD
player. You may find, however, that some players will
not play some recordable media.
For VR mode DVD-RW discs, look for the 'RW
Compatible' mark to see if it will play the disc.

About DV

Using DV, also known as i.LINK, you can connect a DV-
equipped camcorder to this recorder using a single DV
cable for input of audio, video, data and control signals.
The i.LINK interface is also known as IEEE 1394-1995.
"i.LINK" and the "i.LINK" logo are trademarks.
• This recorder is only compatible with DV-format
(DVC-SD) camcorders. Digital satellite receivers and
Digital VHS video recorders are not compatible.
• You cannot connect more than one DV camcorder at
a time to this recorder.
• You cannot control this recorder from external
equipment connected via the DV IN jack.
• It may not always be possible to control the
connected camcorder via the DV IN jack.
• Digital camcorders can usually record audio as
stereo 16-bit/48kHz, or twin stereo tracks of 12-bit/
32kHz. This recorder can only record one stereo
audio track. Set the DV Input setting as required (see
DV Input on page 95).
• Audio input to the DV IN jack should be 32 or 48kHz
(not 44.1kHz).
106
En
• Picture disturbance in the recording may occur if the
source component pauses playback or plays an
unrecorded section of tape, or if the power fails in the
source component, or the DV cable becomes
disconnected.
• The DV IN jack is an input only. There is no output
functionality.
DV-related messages
You may see the following messages appear on your TV
screen when using the DV IN jack.
• No DV camcorder connected. – The camcorder is
not connected properly, or the camcorder is switched
off.
• The DV camcorder is recording. – The camcorder is
recording, so you cannot start recording from the
camcorder to this recorder.
• You cannot connect more than one DV
camcorder at the same time. – The DV jack on this
recorder supports connection to just one camcorder.
• No tape in the DV camcorder. – There is no
cassette loaded into the connected equipment.
• The DV camcorder is in record-pause mode. – The
camcorder is in record-pause mode.
• DV camcorder playback canceled.
Recording has been paused. – Recording was
paused because the camcorder is not in playback
mode.
• Cannot operate the DV camcorder. – This recorder
cannot control the camcorder. Try switching off the
camcorder then switching it back on.
• Could not operate the DV camcorder. – This
recorder was not able to control the camcorder.
• Recording has stopped because the recorded
material on the tape finished. – When the recorded
part of the DV tape comes to an end, this recorder
automatically stops recording.
• Recording has stopped because DV camcorder
playback stopped. – Recording stopped because
DV camcorder playback was stopped or the
camcorder was disconnected.
• The DV camcorder is not set for playback. Please
select playback mode on the DV camcorder. – The
camcorder is in camera mode.