Page 3
14. THREADING THE MACHINE (ONE AND TWO NEEDLE MACHINE) 15. EXCHANGING THE BOBBBIN AND ADJUSTING THE BOBBIN THREAD TENSION 16. WINDING THE BOBBIN THREAD 17. ENGAGING THE SAFETY CLUTCH 18. OIL LEVEL CHECK 19. CLEANING THE MACHINE INSTRUCTION BOOK VETRON 5000 03...
Page 5
INSTRUCTION BOOK 01. OVERVIEW OPERATING PANEL P000 TEST HOTKEYS ELECTRONICS AND SEWING REVERSE CONTROL DONGLE PEDAL INSTRUCTION BOOK VETRON 5000 05...
Turning changes the values; pressing the JOG KEY enters the value. In the following, the operating type is indicated by the following icons: Input = Press the JOG KEY: Change = Turn the JOG KEY: 06 INSTRUCTION BOOK VETRON 5000...
If the backtack function is activated, the following backtack is switched o one time by pushing the key. STITCH LENGTH If the second stitch length is activated, the adjacent LED is lit up. CUSTOMIZABLE BUTTON Default: Toggle foot stroke level INSTRUCTION BOOK VETRON 5000 07...
In the following, the operating type is indicated by the following icons: Pressing the hand wheel: stitch-for-stitch function / needle positioning stitch-for-stitch function / needle positioning Turning the hand wheel: REVERSE SEWING Pulling the button changes the sewing direction. 08 INSTRUCTION BOOK VETRON 5000...
Page 9
INSTRUCTION BOOK 05. CONTROL & MAIN SWITCH MACHINE MAIN SWITCH ON/OFF USB-PORT Identify yourself using the provided USB dongle. INSTRUCTION BOOK VETRON 5000 09...
06. PEDAL IDLE POSITION CONSTANT SEWING SPEED (ADJUSTABLE VIA PARAMETER M502) VARIABLE SEWING SPEED FROM 0-100% OF THE CHOOSEN MAXIMUM SPEED (DEPENDING ON SEWING PROGRAM) SEWING FEET LIFT SEAM END PROCEDURE ACTIVATION (DEPENDING ON SEWING PROGRAM) 10 INSTRUCTION BOOK VETRON 5000...
Page 11
INSTRUCTION BOOK 07. LIGHT The VETRON head module for sewing is equipped with LED sewing area lighting, whose intensity can be controlled via the operating field. For SWITCHING the light ON and OFF, press button » To ADJUST THE LIGHT INTENSITY, proceed as follows:...
Exceptions are listed in the regulation EN 50110. The safety guards must be replaced after finishing the repair and maintenance work. Only original VETRON spare parts or parts which are cleared by VETRON are allowed to use when repairing the machine. Failure to comply will void the warranty.
02. Push the pedal. The sewing feet are moving and finally positioning on the needle plate. NOTE: The red and white control lights at the machine head are flashing during automatic movement. 03. The sewing light is automatically switched on. 04. The machine is now ready for use. INSTRUCTION BOOK VETRON 5000 13...
01. Turn the JOG KEY to the left or right to choose the desired program number. 02. Confi rm your choice by pushing the JOG KEY again. 03. The machine is now ready for use. 14 INSTRUCTION BOOK VETRON 5000...
» Maximum speed » Top feed stroke » Top feed pressure » Bobbin thread counter (only display) » Edge guide distance » Current sewing speed (only display) » Current needle position in degrees (only display). INSTRUCTION BOOK VETRON 5000 15...
Page 16
CAUTION! Only use needles from the system intended for the machine. (see at VETRON GENERAL INSTRUCTION MANUAL – TECHNICAL DATA) 01. Push the X-button at the machine head, the red light illuminates showing the active “blocked mode”, or power o the machine.
Page 17
CAUTION! Only use needles from the system intended for the machine. (see at VETRON GENERAL INSTRUCTION MANUAL – TECHNICAL DATA) 01. Push the X-button at the machine head, the red light illuminates showing the active “blocked mode”, or power o the machine.
Page 18
02. By turning the JOG KEY the sewing feet can be moved. 03. By loosing screws the sewing feet can be exchanged. NOTE! Push the X-button or switch on the machine again and follow the instructions displayed in the control panel. 18 INSTRUCTION BOOK VETRON 5000...
Page 19
Make sure that the thread takeup lever in its uppermost position. Put the thread as shown in the picture. NOTE! Push the X-button or switch on the machine again and follow the instructions displayed in the control panel. INSTRUCTION BOOK VETRON 5000 19...
Page 20
Make sure that the the thread takeup lever in its uppermost position. Put the threads as shown in the picture. NOTE! Push the X-button or switch on the machine again and follow the instructions displayed in the control panel. 20 INSTRUCTION BOOK VETRON 5000...
Page 21
. Close the tab and the hook cover. 05. The bobbin thread tension can be adjusted at screw NOTE! Push the X-button or switch on the machine again and follow the instructions displayed in the control panel. INSTRUCTION BOOK VETRON 5000 21...
80%. NOTE! If necessary the braket can be slightly bended to the left or right to optimize the thread flow to the bobbin. 22 INSTRUCTION BOOK VETRON 5000...
Page 23
06. Check the needle bar rise. (refer to chapter 3.12. of the adjustment manual). If confirmed, the machine is ready for use again. NOTE! Push the X-button or switch on the machine again and follow the instructions displayed in the control panel. INSTRUCTION BOOK VETRON 5000 23...
01. Tilt the machine to the back. The oil tank is located below the base plate. 02. If necessary, slightly pull the oil plug and fi ll the tank up to the “max” marking. 03. Please use only oil types recommended by VETRON. 24 INSTRUCTION BOOK VETRON 5000...
For more cleaning fold the machine back and clean the guard tank. NOTE! If you tilt the machine during power on, a gravity sensor automatically switches the machine into “blocked mode”. This is noted in the display. INSTRUCTION BOOK VETRON 5000 25...