Page 3
5400 » INSTRUCTION BOOK 07/2020 STANDARD » 5400 » 5410...
Page 4
VETRON | Typical GmbH inadmissible and punishable. VETRON | Typical GmbH is only liable for damage caused by intent or gross negligence on the part of the manufacturer. Moreover, liability is excluded.
Page 5
01. OVERVIEW 02. OPERATING PANEL 03. HOTKEYS 04. ELECTRONIC HANDWHEEL & REVERSE SEWING 05. CONTROL & MAIN SWITCH 06. PEDAL 07. LIGHT 08. MACHINE START 09. PROGRAM CHANGE 10. DIRECT ACCESS 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 6
06. PROGRAM ADMINISTRATION WITHOUT USB DONGLE 07. PROGRAM ADMINISTRATION WITH USB DONGLE 08. UPDATE THE OPERATING PROGRAM 06. WEAR PARTS 01. GENERAL INFORMATION 01.01. LISTING 07. WIRING DIAGRAM 01. VETRON 8340 CONTROL BOX 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
The manufacturer assumes no responsibility for damage caused by changes or modifications. » For repairs, only spare parts approved by VETRON may be used. In case of infringement the guarantee expires. » The machines are to be used only for the purpose intended.
Page 8
This symbol indicates that there is an increased risk of burning here. MAGNET! This symbol indicates that there is a magnet field. INFORMATION! This symbol displays information. ADVICE! This symbol indicates important information. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Risk of injury due to rotation. SAFETY PRECAUTIONS! The eye protection can be ordered optionally, but must not be removed after installation without consultation with the operator. The finger guard must not be removed! 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Damage due to non-intended use is not covered by the manufacturer‘s liability! The VETRON 5400 and its subclasses are 1-needle lockstitch sewing machine with direct drive and triple feed. Use the machines only according to their technical data and for medium to heavy ma- terials such as jeans, leather, etc..
350 x 130mm Netto weight 55 kg Gross weight 70kg Operating voltage AC 220-240V / 50-60Hz Rated power 1200W Noise indication 80dB(A) Versions and subclasses can be found under: www.vetrontypical.com 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
02. Pull out the mains plug. 03. Disconnect the machine from the compressed air supply, if available. 04. Clean the machine if necessary. 05. If possible, cover the machine to avoid soiling. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Turning changes the values; pressing the JOG KEY enters the value. In the following, the operating type is indicated by the following icons: Input = Press the JOG KEY: Change = Turn the JOG KEY: 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 15
If the backtack function is activated, the following backtack is switched o once by pushing the key. STITCH LENGTH If the second stitch length is activated, the corresponding LED lights up. CUSTOMIZABLE BUTTON Default: Toggle foot stroke level (see parameter M085) 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Pressing the handwheel: stitch-for-stitch function / needle positioning Turning the handwheel: REVERSE SEWING Pulling the button changes the sewing direction. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 17
02. MACHINE DESCRIPTION 05. CONTROL & MAIN SWITCH MACHINE MAIN SWITCH Switches the machine ON / OFF USB-PORT Identify yourself using the provided USB dongle. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
CONSTANT SEWING SPEED (adjustable via parameter M502) VARIABLE SEWING SPEED FROM 0-100% OF THE CHOSEN MAXIMUM SPEED (depending on sewing program) SEWING FEET LIFT SEAM END PROCEDURE ACTIVATION (depending on sewing program) 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Change LIGHT INTENSITY light intensity of the light are changed. After 2 seconds without further input, the value is set and the current program number is shown. Machine is ready for operation 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
The red and white control lights at the machine head are flashing during automatic movement. 03. The sewing light is automatically switched on. 04. The machine is now ready for use. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
03. Turn the JOG KEY to the left or right to choose the desired program number. 04. Confirm your choice by pushing the JOG KEY again. 05. The machine is now ready for use. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Before activating the machine by the X-button make sure to remove sewing material or other items below the sewing feet if necessary and follow the instructions displayed on the control panel. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 24
02. By turning the JOG KEY the sewing feet can be moved. 03. By loosening screws the sewing feet can be exchanged. NOTICE! Push the X-button or switch the machine on again and follow the instructions displayed on the control panel. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Now you can thread the machine according to the picture. NOTICE! Push the X-button or switch the machine on again and follow the instructions displayed on the control panel. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 26
05. Insert the bobbin capsle with filled bobbin into the hook and close cover. 06. The bobbin thread tension can be adjusted at screw NOTICE! Push the X-button or switch the machine on again and follow the instructions displayed on the control panel. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
There should be a gap of 1 mm between thread and bobbin edge. NOTICE! If necessary, the bracket can be slightly bended to the left or right to optimize the thread flow to the bobbin. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 28
03. OPERATION OF THE MACHINE 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
In the following chapter we will introduce you to the most important mainte- nance areas to be checked daily & before each use. Detailed maintenance and cleaning instructions can be found in the respective adjustment instruc- tions in chapter 05. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
If neccesary, fill in Oil. To do this, pull plug out. Oil level visiable in window Please use only oil types recomended by VETRON or an equivalent oil with the following specification: E.g.: oil PP 20 DAB 10 (Viscosity 40°C: 15 mm /s;...
» bobbin housing » feeders » thread trimmer » needle area NOTICE! Clean the hook area daily. With increased lint production, depending on materials, clean the hook area several times a day. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
SEWING DRIVE: » Remove the covers to check the timing belts. » Remove the cover to check or/and clean the main drive fan grill. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
» Unscrew the water seperator » Unscrew the filter cartridge Wash the filter shell and cartridge with cleaning fluid (no solvent) and blast clean. » Re-assemble the maintenance unit. Check for system leaks. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 35
The thread tension, foot pressure and stitch length are adjusted with increasing material With the VETRON, these settings are made by step motors, they thickness. can exactly reproduce the desired setting. All settings for e.g.
Page 36
Turn the JOG KEY to select the desired parameter. Push the JOG KEY. The parameter will flash and can be changed by turning the JOG KEY. Pushing the JOG KEY again will store your input. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 37
The appropriate LED will shine on the display. ► Parameter 1 appears on the display. Now you can change the name. ► Turn the JOG KEY to the right. You are directed to the program parameters. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 38
Switching over can be done with key or the electronic handwheel 021 Foot stroke 2 It can also be done with a knee lever (optional) or with the automatic switch parameter 027. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 39
The stroke on an alternate machine are normally changed by pressing a 027 Automatic stroke switch button or with a knee lever. The VETRON can do this also automatically with the foot pedal. By activating parameter 027 it will activate the facility.
The thread tension on conventional machines is adjusted with a spring. The reproduction of the desired thread tension is di cult. The VETRON sets the thread tension with a step motor. The task of the tension spring is taken over by a elastomer. A second thread tension on conventional machines needs an additional tension unit.
Page 41
040 Speed mode Function 1 = PEDAL Sewing speed will be regulated by the posititon of the pedal. Function 2 = CONSTANT Constant sewing speed as selected in parameter 041. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Automatic foot pressure control On conventional machines the foot pressure is generated by a spring and will be adjusted seldom. The VETRON also generates the foot pressure with a spring, but the spring is pre-stressed by a step motor with gear (parameter 050). In di erent programs can di erent foot pressure be applied.
Page 43
Operation mode CONSTANT 4 mm 2 mm 30% adjusted Material thickness in mm Foot pressure High percentage in % Low percentage Operation mode 1-100% (Pressure increase over speed) 30% adjusted Speed 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 44
Parameter 078 can only be selected when the position of stitch placing 078 Target stitch position is activated in parameter 085, 086 or 087. The position of the needle point above the material is set with this parameter. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 45
STROTG = Foot stroke for this program. (By pressing the key you will switch to the 2 stroke. Pressing it again will change back to the 1 stro- ke). 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 46
086 Handwheel function ( Same functions as parameter 085, when the electronic handwheel is pushed 087 Knee switch function You have the same function as parameter 085, when the knee switch is pushed. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 47
The stitches will be exactly in the same position with the stitch in stitch backtack. The feeding will be switched when the machine is standing still. It is used for visible backtacks with high quality. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
(parameter 010) (e.g. 4.0 mm). -4.0 mm = When the stitch length for A in backtack is entered in the minus range this part of the backtack will be done in reverse. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 49
After changing the bobbin you have to press the safety switch (X Key) to reset the bobbin thread counter. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
(parameter 010) (e.g. 4,0mm). -4.0 mm = When the stitch length for B in backtack is entered in the minus range this part of the backtack will done in reverse. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
A chain program can be used when di erent operations on a work piece are done one after the other. The machine will set itself automatically for the next work step. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 52
= The next work step is initiated by pressing the key . (see next page) Electronic handwheel = The next work step is initiated by pressing the electronic handwheel . (see next page) 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 53
= The switch will take place (if part of the program) after the end backtack and thread trimming (picture 3). The next seam starts with a backtack (picture 4) (if part of the program). Picture 3 Picture 4 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 54
Push the JOG KEY to accept your selection. Choose number for this program. ► Push the JOG KEY to accept your selection. Enter program name or number on the display. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 55
Summary chain program: Up to 10 chain links PROGRAMM SEAM START SEAM SWITCH OVER OPTION END OF SEAM 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 56
Turn the JOG KEY to select a letter or number. Up to 15 letters or numbers can be entered. ► Push the JOG KEY to jump to the next free space. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 57
YES or NO. Y S N E / O D l t e e e ► Push the JOG KEY to confirm selection. The display will show COPY PROGRAM. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 58
Once the dongle is inserted into the USB-Port, a file with the serial number of the machine will be opend automatically. In this way you can transfer program from one machine to another. Serial number and program can be selected and transfered to the appropriate machine. Please use only VETRON USB Dongles to secure a safe transfer of data. DISPLAY...
Page 59
Turn the JOG KEY to select the relevant machine. 0 1 4 ► Push the JOG KEY ► Turn the JOG KEY to select the desired program. ► Push the JOG KEY 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 60
0 3 0 YOUR MACHINE NUMBER WILL BE SHOWN ON THE DISPLAY IN BRACKETS. ► Turn the JOG KEY to select desired machine. 0 1 4 ► Push the JOG KEY 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 61
All data will be transferred to the USB dongle. > ► Turn the JOG KEY to select YES or NO. Y S N E / O ► Push the JOG KEY to confirm your selection. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 62
Push the JOG KEY All data will be tranfered to the machine. > NEVER remove the USB dongle while data is being transferred. Display will show CONFIGURATION USB ---> MACHINE. > 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 63
Appears. Turn machine o ! Turn machine on again. Now the machine with the new update can be operated on. INFO: If there is no information on DONGLE, „Error“ appears! 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
» This Wear Parts List shows the main parts of the machine. A detailed list for the complete machine is available on our website www.vetrontypical.com and can also be ordered as a manual. 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...
Page 66
559 1545 10 DIN 988 3x6x1 (only for 22mm hook) 559 3218 13 (26mm) 559 1538 13 (22mm) DIN 85 M2x5 559 0296 16 C144588201 (C) Tension Spring C144588301 (B) 07/2020 VETRON 5400 - CYLINDER ARM MACHINE - INSTRUCTION BOOK...