Design; Pco5+ Design - Carel pCO5+ User Manual

ENG
On the models where they are included, the front panel contains a display
and a keypad with 6 backlit buttons that, when pressed individually or in
combination, allow the following operations:
•
uploading an application program;
•
commissioning.
During regular operation and depending on the application program
installed, the terminal can be used:
•
to edit the main operating parameters;
•
to display the quantities measured, the active functions and any alarms
detected.

2.1 pCO5+ Design

J11 pLAN
J10
H
FieldBus card
J1 J24 J2 J3
A B D
Each controller is provided with connectors for the inputs/outputs (see
chap. 5) and the secondary display, which has a button and a LED for
setting the pLAN address. Depending on the model, it can be supplied
with a built-in terminal and USB ports.
Keypad
Button Descr. Backlighting Functions
Alarm White/Red
Prg White/Yellow -
Esc White
UP White
Enter White
DOWN White
pLAN
address -
selection
Note: Once the application program is installed, all button
functions depend on the program and do not necessarily correspond to
the descriptions above.
pCO5plus +0300020EN rel. 1.2 - 07.11.2013

2. DESIGN

only model with built-in driver
J12 J13 J14 J15
4 3 2 1
J21
J25 BMS2 J26 FBus2
E
F
G
J19
C
B M S card
J4 J5 J6
J30
only model with built-in driver
• press together with UP while providing
power to change the controller's address
(see par. 6.3).
• press together with Enter to access the
screens managed by the BIOS (see par.
6.6).
go up one level
• press together with DOWN and ENTER to
change the terminal's address (only for
PGDE terminal - see par. 6.4).
• press to increase value.
press to confi rm value.
• press together with UP and ENTER to
change the terminal' s address (only for
PGDE terminal - see par. 6.4).
• press to reduce value.
• pressed briefl y: displays the pLAN
address.
• long press (>5 s): procedure for changing
pLAN address (see par. 6.3).
Key:
A
J27
J28
B
C
J16 J17 J18
D
E
J22
J23 Fus2 F
G
H
(*) available on P+5... models; not available on P+3...
models; see par. 8.3.
J20
J7 J8
J29
A B C D
Fig. 2.a
Display
The controller is provided with two displays:
•
the main display on the built-in terminal (if included);
•
the secondary display showing the controller's pLAN address.
LED
The more complete models are provided with 6 LEDs:
•
1 yellow LED indicating that the device is powered;
•
1 red LED indicating an overload on the +VDC (J2-5) terminal;
•
4 LEDs indicating valve status (only on pCO5+ built-in driver models).
Flashing LEDs mean the valve is moving; steadily-on LEDs mean the
valve is completely open or closed.
LED Colour
A Yellow
B Green
C Yellow
D Green
Microswitches
Four microswitches are provided to confi gure port J26 as a Fieldbus or
BMS port (see "Port J26 confi guration").
USB ports
On the models where they are included, there are 2 USB ports which can
be accessed after removing the cover:
•
a "host" USB port for connecting pendrives;
•
a "slave" USB port for direct connection to the USB port of a computer
on which pCO Manager is installed, which can be used to upload the
application program, commissioning the system, etc.
12
pLAN address selection button
pLAN address display(*)
Power LED
Overload LED
J26 port Fieldbus/BMS microswitches(*)
Host USB port (master)(*)
Slave USB port (device)(*)
Main display
Description
close valve A (connector J27)
open valve A (connector J27)
close valve B (connector J28)
open valve B (connector J28)