Shipping And Packing List; Operating And Storage Environment, Electrical And Dimensions; Installation Recommendations; Smart Hub Installation, External Components, Leds, Terminals & Jumpers - Lennox iComfort E30 Installation And Setup Manual

Shipping and Packing List

Quantity Description
1 iComfort® E30 smart thermostat includes a Smart Hub, HD Display, Mag-Mount and
optional use wall plate.
6 Mounting screws (#6 X 1.25" pan head) - Mag-Mount requires 4 and Smart Hub
2.
6 Wall anchors (alligator flanged solid wall anchors)
1 Installation and setup guide
1 User guide
1 Checklist
1 Warranty certificate
IMPORTANT
The iComfort E30 smart thermostat CAN NOT be connected as a communicating
device to indoor or outdoor units. Only conventional 24VAC wiring to indoor and
outdoor units is supported.
NOTE: Due to Lennox' ongoing commitment to quality, features and options are
subject to change without notice and without incurring liability. Improper
installation, adjustment, alteration, service or maintenance can cause
property damage or personal injury. Installation and service must be
performed by a qualified installer and servicing agency.

Operating and Storage Environment, Electrical and Dimensions

• Operating Temperature is -40°F to 175°F (-40°C to 79°C)
• Shipping and storage temperature range is -40°F to 185°F (-40°C to 85°C)
• Operating humidity range is 10% to 90% non-condensing at 104°F (40°C)
• Storage humidity range is 5% to 95% non-condensing at 104°F (40°C)
• E30 Smart Hub Power Input: 24VAC, 1AMP at 60Hz.
• E30 Smart Hub DC Power Output: 12VDC (to Mag-Mount/HD Display)
• Dimensions (H x W x D):
Mag-Mount: 3-1/4" x 3-1/4" x 1/2" (83 x 83 x 13 mm)
»
HD Display: 5" x 7-1/2" x 1" (127 x 19 x 25 mm)
»
E30 Smart Hub: 11-3/8" x 7-1/4" x 1-3/4" (289 mm x 184 mm x 46 mm) -
»
antenna length is 7-1/4" (184 mm)

Installation Recommendations

Improper installation, adjustment, alteration, ser vice or maintenance can cause
property damage, personal injury or loss of life.
Installation and service must be performed by a li censed professional HVAC
installer (or equivalent) or a service agency.
Before beginning installation, note the type of equipment, number of stages, and
any accessories being installed.
Do
• Read this entire document, noting which procedures pertain to your specific
equipment and system requirements.
• Make sure that all wiring conforms to local and national building and electrical
codes and ordinances.
Do Not
• Install on voltages higher than 30VAC.
• Exceed 300 feet (91 meters) run when using 18 GAUGE thermostat wire or larger.
• Allow power load from any thermostat connection to be more than 1 AMP.
Smart Hub Installation, External Components, LEDs, Terminals & Jumpers
1. Things to consider when installing the Smart Hub:
• Install the Smart Hub near the indoor unit such that there is a direct path to
the approximate location of the home Wi-Fi access point (the signal is not
blocked by the indoor unit or duct work, for example).
• The Smart Hub can be attached to a vertical surface such as a wall stud
or roof truss web, or to a horizontal surface such as a floor or ceiling joist,
or a roof rafter.
• The Smart Hub antenna should be positioned such that it is roughly vertical,
no matter the orientation of the Smart Hub, itself.
• Do not install the Smart Hub on the indoor unit, duct work, or other
equipment that could induce vibration in the Smart Hub.
• Do not install the Smart Hub on or near large metal objects. This could
adversely affect the range and directional coverage of the Smart Hub Wi-Fi
signal.
• If the Smart Hub MUST be installed on a metal object, orientate the antenna
perpendicular to the metal surface.
• In all cases, the Smart Hub antenna orientation may need to be adjusted to
obtain best Wi-Fi results.
3
WARNING