VIDEX ELECTRONICS S.p.A.
ART.KRA78/KRA76 CITOFONI VIVAVOCE LINEA
KRISTALLO)
Descrizione
Citofono vivavoce intelligente specifico per il sistema VX2200 con pulsanti
touch sensitive aventi funzione di "apri-porta/chiamata a portiere", "rispo-
sta/auto-accensione", "privacy" e "servizio" più 4 pulsanti per le regolazioni
dei volumi di suoneria, fonia e per le programmazioni. 4 LED* forniscono
indicazioni visive circa il funzionamento del citofono. Nella versione da su-
perficie, Art.KRA76, è presente anche la cornetta per l'utilizzo convenzionale
in aggiunta alla modalità vivavoce.
Le regolazioni possibili sono:
Volume della suoneria;
Volume della fonia;
Le programmazioni sono:
Indirizzo del citofono (da 1 a 180);
Durata privacy (da 30 minuti a 20 ore o illimitata);
Tipo di suoneria (9 disponibili);
Numero di squilli (da 1 a 9);
Ingressi di tipo attivo basso per chiamata locale ed allarme.
Pulsanti e Regolazioni
Alla ricezione della chiamata, abilita l'inizio conversazione.
Il relativo LED si accende.
Ad impianto acceso, consente lo spegnimento manuale (ra-
pida pressione del tasto). In ogni caso lo spegnimento è au-
tomatico (il relativo LED si spegne) allo scadere del tempo
di conversazione.
Premendo il pulsante per più di 2 secondi, il videocitofono
passa nel modo trasmissione ad una via: per parlare con
l'esterno occorre tenere premuto il pulsante (il LED lam-
peggia rapidamente), mentre per ascoltare il visitatore oc-
corre lasciare il pulsante (il LED lampeggia lentamente).
Trascorsi 10 secondi senza premere nuovamente il pulsante,
il sistema si spegne. Il videocitofono torna al funzionamento
normale alla successiva accensione.
Ad impianto spento, premere il pulsante tante volte quant'è
il valore dell'identificativo del posto esterno da accendere.
Il relativo LED si accende (questa funzione è disponibile
solo se abilitata tramite la procedura in seguito descritta in
questa sezione).
A sistema acceso, apre la porta. L'apertura è indicata da un
segnale acustico. Se il relativo morsetto è stato opportuna-
mente collegato, il LED in corrispondenza al pulsante chia-
ve resterà acceso per tutto il tempo che la porta resta aperta.
A sistema spento effettua la chiamata al centralino di porti-
neria se presente nell'impianto.
Con il sistema in stand-by, premere rapidamente per attivare
il servizio privacy per il tempo programmato: il relativo
LED si accende a segnalare lo stato di attivazione del servi-
zio. All'arrivo della chiamata, con il servizio attivo, l'unità
non emette alcun segnale acustico. Il servizio si disattiva al-
lo scadere del tempo programmato o premendo nuovamente
il pulsante.
Con il sistema in stand-by, tenere premuto questo pulsante
fino a che l'unità non emette un bip e il relativo LED si ac-
cende per entrare nel menù di programmazione della durata
privacy.
A videocitofono in conversazione o in stand-by, premere que-
sto pulsante per abilitare l'uscita di tipo basso "SB" per 2 se-
condi. Il relativo LED si illumina per 2 secondi e il citofono
emette 2 bip.
Con il sistema in stand-by, premere + o – (il citofono emette
un bip ad ogni pressione) per incrementare o decrementare il
volume della nota di chiamata: un doppio bip rapido segnala il
raggiungimento del massimo o del minimo livello.
Durante la conversazione, premere + o – (il citofono emette un
bip ad ogni pressione) per incrementare o decrementare il vo-
lume della fonia: un doppio bip rapido segnala il raggiungi-
mento del massimo o del minimo livello.
VX2200 "2 WIRE" Bus Digital System
ART.KRA78/KRA76 KRISTALLO HANDSFREE INTER-
COMS
Description
Intelligent Hands free intercom for the VX2200 digital system with touch sen-
sitive buttons for "door open/concierge call", "answer/camera recall", "pri-
vacy" and "service" plus 4 buttons for volume adjustment and programming
plus 4 LEDs related to the intercom operation. For the surface version only
(Art.KRA76), a handset can also be used in addition to the handsfree mode.
The following programmable options are available:
Call tone volume;
Speech volume;
Intercom address (from 1 to 180);
Privacy duration (from 30 minutes to 20 hours or unlimited);
Call melodies (9 available);
Number of rings (from 1 to 9);
Additionally the Kristallo has an input for local door bell and alarm.
Push buttons and Controls
Press this button during an incoming call to open the
speech in half duplex mode allowing free speech with the
caller in both directions (The related LED will illuminate).
During a conversation, momentary operation of this button
will end the call. The LED next to the button will switch off.
The system will automatically switch off when the conversa-
tion time expires.
Press and hold this button (more than 1 second), during an
incoming call or a conversation in progress, to allow the
user to answer a call from a visitor at the door station in
SIMPLEX speech mode (The related LED will flash rapid-
ly): releasing the button will allow the user to listen to the
visitor (The LED will flash slowly). Press and hold the but-
ton when you talk to the visitor and release the button when
you listen to the visitor.
When the system is in standby, (No calls on the system) op-
eration of this button will open the speech to the door sta-
tion (Only when the recall facility is enabled). The related
LED will illuminate. Press as many time as the ID value of
the door panel to connect to.
During a conversation, operation of this button will release
the door from where the call originated. This will be con-
firmed by an acoustic tone. If terminal "DL" is connected,
the "door open" LED next to the button will also be illumi-
nated.
When the system is in stand-by, a button press will book a
call to the concierge (If available)
When the system is in stand-by, press this button to enable
the service for the programmed time: the related LED will
illuminate to signal the service enabled. During an incom-
ing call, with the service enabled, the device does not emit
any acoustic signal. The service is disabled when the pro-
grammed time expires or pressing again the button.
When the system is in stand-by, keep pressed this button
until the unit emit a beep and the related LED switches ON
to enter to privacy duration programming menu.
Press this button to enable the active low output "SB" for 2
seconds. The related LED illuminates and the intercom emits
two beep.
When the system is in stand-by, press + or – (the intercom
emits a beep) to increase or decrease the volume level of the
call tone: two short beeps signal the maximum or minimum
level reached.
When intercom is in conversation, press + or – (the intercom
emits a beep) to increase or decrease the volume level of the
speech: two short beeps signal the maximum or minimum level
reached.
103