VIDEX ELECTRONICS S.p.A.
Impostazione suoneria e regolazione volume suoneria – VR5178
Con il sistema in stand-by, premere e tenere premuto (circa 10 secondi) il
pulsante "
" fino a che il citofono non riproduce la suoneria corrente e
si accendono i LED "parla" e "privacy". Terminata la riproduzione della
suoneria correntemente attiva, il citofono emette un bip ed i LED "parla" e
"privacy iniziano a lampeggiare.
Per regolare il volume della suoneria, premere ripetutamente o tenere pre-
muto il pulsante " " per diminuire o il pulsante " " per incrementare (il
volume dei bip emessi varia in base al pulsante che si sta premendo).
Ad ogni pressione del pulsante "
ria (max 9 disponibili): i LED "parla" e "privacy" smettono di lampeggia-
re, viene riprodotta la nuova suoneria, al termine viene emesso un bip ed i
LED tornano a lampeggiare.
Ripetere il passo precedente per selezionare una nuova suoneria altrimenti
attendere circa 3 secondi (i LED si spengono) senza premere alcun pulsante
per selezionare la suoneria appena ascoltata e fissare il livello di volume.
Impostazione durata privacy – VR5178
Con il sistema in stand-by, premere e tenere premuto (circa 10 secondi) il
pulsante " " fino a che il relativo LED inizia a lampeggiare e viene emes-
so un bip.
Ad ogni pressione del pulsante " " il tempo (max 20 ore) viene incremen-
tato di 30 minuti a partire da 0. Per impostare il modo privacy "infinito" (il
servizio viene disattivato solo premendo nuovamente il pulsante) passare
al passo successivo senza premere nulla.
Raggiunta la durata desiderata (es. per impostare 3 ore premere 6 volte)
attendere senza premere nulla che il LED si spenga.
La nuova durata della privacy è memorizzata.
Regolazione volume della fonia – VR5178
A conversazione in corso (LED "parla" acceso), premere il pulsane " " :
il LED "parla" si spegne ed inizia a lampeggiare il LED "privacy".
Premere ripetutamente o tenere premuto il pulsante " " per diminuire il
volume della fonia o il pulsante "
Raggiunto il livello di volume desiderato , attendere circa 3 secondi senza
premere nulla o premere nuovamente il pulsante " ".
Il LED "privacy" smette di lampeggiare spegnendosi ed il LED parla si
riaccende.
Programmazioni e Regolazioni – VR5478
Il videocitofono ha due differenti menù per operazioni di programmazione e
regolazione:
1.
Un menù viene attivato dalla condizione di stand-by e consente di im-
postare:
La durata della "privacy";
Il volume della suoneria;
Il tipo di suoneria;
Il numero di squilli;
2.
Il secondo menù è accessibile quando il videocitono è in funzione (du-
rante una conversazione o auto-accensione) e consente di impostare:
Il volume della fonia;
La luminosità;
Il Contrasto;
La saturazione;
Menù 1
Con il sistema a riposo (monitor spento) premere e tenere premuto (circa 9
secondi) il pulsante " " per entrare nel menù di programmazione;
Il monitor si accende mostrando il menù OSD: la parte superiore dello
schermo riporta la scritta "menù" seguita dall'icona della funzione selezio-
nata mentre la parte inferiore indica a sinistra il valore della funzione sele-
zionata, al centro l'icona della funzione selezionata e a destra l'icona della
successiva funzione disponibile.
La prima funzione disponibile è la durata della privacy (massimo 20 ore):
premere ripetutamente o tenere premuto il pulsante "
re o il pulsante " " per decrementare la durata di mezzora ad ogni step
(segnalato da un bip).
Premere il pulsante " " per memorizzare il nuovo valore e accedere alla
programmazione successiva.
La seconda funzione è il volume della suoneria: premere ripetutamente o
tenere premuto il pulsante "
decrementare il volume della suoneria ad ogni step (segnalato da un bip).
Premere il pulsante " " per memorizzare il nuovo valore e accedere alla
programmazione successiva.
La terza funzione è il tipo di suoneria: premere il pulsante "
ascoltare e selezionare la suoneria precedente o il pulsante " " per ascol-
tare e selezionare la suoneria successiva.
114
VX2200 "2 WIRE" Bus Digital System
" viene selezionata una nuova suone-
" per incrementare.
" per incrementa-
" per incrementare o il pulsante " " per
VR5178 – How to setup a melody and volume
When the system is in stand-by, press and hold pressed (approx 10 sec-
onds) the button "
the "talk" and "privacy" LEDs illuminate. At the end of current melody
play the intercom emit a beep and the LEDs "talk" and "privacy" start to
flash.
To adjust the volume of the melody, press several times or hold pressed the
button " " to decrease or the button " " to increase (the volume of
emitted beeps vary according to the button pressed).
Each time the button "
selected: the LEDs "talk" and "privacy" stop flashing, the new melody is
played, at the end a beep is emitted and the two LEDs restart to flash.
Repeat the step above to select a new melody otherwise wait approx 3 sec-
onds of idle time (the LEDs turn OFF) without pressing any button to select
the melody played and set the volume adjusted.
VR5178 - Privacy duration programming
Press and hold the " " button (for approx 10 seconds) until the unit emits
a beep and the related LED starts flashing.
Each time the" " button is pressed, it will increase the privacy duration
by 30 minutes (starting from 0 up to a maximum of 20 hours i.e. pressing
the button 6 times = 3 hours up to a maximum of 40 presses for 20 hours).
To set the privacy with no time out do not press the button.
Once the required privacy duration has been reached, wait 3 seconds for
the exit beep.
The new value is now stored.
VR5178 – Speech line volume adjustment
When a conversation is in progress ("speak" LED illuminated), press the
" " button: the "privacy" LED starts flashing and the "talk" LED turns
OFF.
Press more times or hold pressed the " " button to decrease the speech
volume or the "
" button to decrease.
Once the required volume level is reached, wait approx 3 seconds of idle
time or press again the " " button.
The "privacy" LED stops flashing and turns OFF while the "talk" LED
turns back ON.
Programming and Adjustments – VR5478
The videomonitor has two different menus for programming and adjustment
functions:
1.
One menu operates when the system is in stand-by and allows to set:
The privacy duration;
The melody volume;
The melody type;
The number of rings;
2.
The second menu operates when the system is turned ON (during a con-
versation or a camera recall) and allows to set;
Speech volume;
Brightness;
Contrast;
Hue;
Menu 1
When the system is in stand-by (monitor turned OFF) press and hold
pressed (approx 9 seconds) the " " button to enter the programming
menu;
The OSD menu appears on the display: the top of the screen shows
"menu" followed by the available function icons, the bottom of the screen
shows the currently selected function value on the left, the currently select-
ed function icon in the middle and the next function icon on the right side.
The first function available is the privacy duration (max 20 hours): press
as many times or hold pressed the "
button to decrease the duration of a half an hour each step (signalled by a
beep).
Press the " " button to store the new value and to enter the following
programming function.
The second function is the melody volume: press as many times or hold
pressed the "
" button to increase or the " " button to decrease the
melody volume level (signalled by a beep).
Press the " " button to store the new value and to enter the following
programming function.
The third function is the melody type: press the "
" per
select the previous melody or the " " button to hear and select the fol-
lowing melody.
" until the intercom plays the current melody and
" is pressed, a new melody (9 are available) is
" button to increase or the " "
" button to hear and