Recommended Professional Installer Basic Rules; Specifications; Annex A (Manuals Of System Items) - jablotron JA60K Installation Manual

works as normal
JA60P movement detector
repeatedly triggers alarms
with no visible reason
fault C is indicated on the
control panel
when activated, the tele-
phone dialer calls a number
multiple times
problem is not in this list

10. Recommended Professional installer basic rules

If you install the system for a customer, you should follow these rules:
• make a drawing of intended location of the items, keeping in mind proper protection for the intended area.
• if the customer requests reduction of the system (price reasons etc.), ask for a written confirmation that he does not
want the particular items you recommended (to avoid blame and liability if poorly covered area is robed in the future)
• make a professional installation and do not forget to clean and be tidy.
• it is very important to explain to the customer all functions of the system, to teach to him or her how to program access
codes, how to test the system and how to replace batteries in the items
• offer your regular assistance for testing and battery replacement (we recommend annually)
• make a written report signed by the customer, that the installation was finished properly and that she or he received
your training on how to operate and test the system

11. Specifications:

control panel power
back up battery
back up power output
number of zones (detectors)
number of controllers (keypads) max. 8
events memory
built in siren
working frequency
RF approved according
complies with
telephone dialer*
approved according*
working environment
Event indicators – informs what happened in the system. Display specifies from where the event is reported.
alarm triggered by an intruder, smoke, gas etc. See specification on the display
alarm
tamper opened cover, damaged detector, excessive number of attempts to enter code etc. See specification on the display.
power loss, lost communication with a detector etc., see specification on the display (confirm pressing key N)
fault
battery of the device specified on the display is low. See battery replacement below.
battery
Display specifies event source or mode of the control panel
event source:
1 to16
c1 to c8
C
A
J
L
d
programming mode
P
user mode (battery replacement & testing)
U
H home (partial) arming (detectors 11 to 16 are bypassed)
− − − −
waiting for more data to complete instruction
continues = armed
armed
slow blinking = exit delay
Alarm system JA-60 "COMFORT"
ready.
check if there are: animals in the protected area
(mice...), sudden changes of temperature or intense
air circulation, movement of objects with temperature
of about 37°C etc.
technical problem of the control panel – failure of the
power supply, blown fuse in the panel etc.
the telephone network (mobile network) does not use
standard recognition signals and the dialer is not sure
if the connection was successful or not
call installer or the distributor for advice
230VAC, 50Hz (110VAC, 60Hz optional)
12V, 1,3Ah ref. 12V1K optional
13.8V, max. 50mA (permanent load), max. 1A (10 minutes)
16
127 latest events incl. date and time information
118dB
433.92 MHz (optional)
I-ETS 300 220
EN 50131-1, 50131-5
voice message to 4 numbers
numeric message to a Pager
digital communication to a monitoring station
TBR21
indoor use, -10 to +40°C
•
only for control panels equipped with the telephone dialer module
User instructions of JA-60 „Comfort"
detector number
controller or keypad number
control panel
wireless siren
sub system (other JA-60 system linked to first system)
telephone line
digital line (PC interface)
-
21 -
gramming mode
increase detector's immunity (DIP
SW 1 to pos. 1), change location of
the detector or use an optional sen-
sor's lens
check AC adapter, backup up bat-
tery, fuses or call installer
for calls to GSM network store F0
after the last digit to the number
(see 7.2.22)
local hot line number:
MDY51306