Universal Laser Systems X-600 Safety, Installation, Operation, And Basic Maintenance Manual page 78

Open the front door of the laser system

and carefully slide the cutting table into
the laser system so that its body is
squarely pushed up against the engraving
table rulers on the top and the side of the
table. The rulers of the cutting table
should now overlap the rulers on the
engraving table.
 Slide the adjustable manifold squarely up
against the exhaust plenum and tighten
the four (4) screws on the side of the
cutting table. Be careful not to move the
cutting table while tightening the screws.
The objective is to have the cutting table fit
snugly up against the rulers of the
engraving table
manifold fit tightly against the exhaust
plenum.
We now need to adjust the rulers of the

cutting table so that they match the
engraving field of the laser system. Using
the focus tool method, adjust the Z Axis
and focus directly onto the surface of the
honeycomb.
 Loosen slightly, but do not remove, the
five (5) screws that hold down the rulers.
1 2 3 4 5 6 7 8
1
2
3
4
5
6
7
8
9
10
11
12
SCREWS
Activate the red diode pointer. Position the focus carriage at (0,0). With the red diode pointer still

ON, slide the X-axis ruler so that its zero (0) point lines up with the red diode pointer and tighten
down the left side screw.
Now position the red diode pointer at the (32,0) position for the X series machine or (24,0)

position for the M or V series machine. Adjust the right side of the X-axis ruler until it is lined up
with the diode. Tighten down the right side screw of the X-axis ruler. Now tighten down the
middle screw.
 Line up the right edge of the Y-axis ruler with the zero (0) line of the X-axis ruler and tighten down
the top screw of the Y-axis ruler.
Finally, position the red diode pointer at the (0,18) position for the X series machine or the (0,12)

position for the M or V series machine. Align the bottom of the Y-axis ruler with the red diode
pointer and tighten down the bottom screw of the Y-axis ruler. The cutting table is now ready for
use.
When removing the cutting table, lower the engraving table and slide the table out of the front door.
Re-install the exhaust plenum strip(s). As long as you followed the installation instructions exactly, it
is designed so that you will NOT need to adjust the adjustable manifold or the X or Y-axis rulers when
re-installing the cutting table.
ACCESSORIES
and the adjustable
SCREWS
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Section 6-12
2 3 4 5 6 7 8 9
1
1
2
1 2 3 4 5
3
1
4
2
5
3
6
4
7
5
8
6
9
7
10
8
11
9
12
10
11
12
ENGRAVING TABLE
ADJUSTABLE MANIFOLD
1 2 3 4 5 6
1
SCREWS
2
3
4
5
6
7
8
9
10
11
12
1) POSITION DIODE HERE
24 1 2 3 4 5
1
2
3
4
5
6
7
8
9
10
11
12
3) AND FINALLY HERE
10 11 12 13 14 15 16 17 18 19 20 21
ADJUSTABLE MANIFOLD
6 7 8 9 10 11 12 13 14 15 16 17 18
CUTTING TABLE
EXHAUST PLENUM
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
2) THEN HERE
X-AXIS RULER
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
22 23 24
19 20 21 22 23 24
23 24
SCREWS
21 22 23