Siemens SIPROTEC 7SD80 Manual page 366

Appendix
A.8 Settings
Addr. Parameter
2801 DMD Interval
2802 DMD Sync.Time
2811 MinMax cycRESET
2812 MiMa RESET TIME
2813 MiMa RESETCYCLE
2814 MinMaxRES.START
2901 MEASURE. SUPERV
2902A BALANCE V-LIMIT
2903A BAL. FACTOR V
2904A BALANCE I LIMIT
2905A BAL. FACTOR I
Σ I THRESHOLD
2906A
Σ I FACTOR
2907A
2908A T BAL. V LIMIT
2909A T BAL. I LIMIT
2910 FUSE FAIL MON.
2911A FFM V>(min)
2912A FFM I< (max)
2913A FFM V<max (3ph)
2914A FFM Idiff (3ph)
2915 V-Supervision
2916A T V-Supervision
2931 BROKEN WIRE
FAST Σ i SUPERV
2933
ΔI min
2935A
3401 FCT 79
3402 52? 1.TRIP
3403 T-RECLAIM
3404 BLOCK MC Dur.
3406 EV. FLT. RECOG.
366
Function C Setting Options
Demand meter 15 Min., 1 Sub
15 Min., 3 Subs
15 Min.,15 Subs
30 Min., 1 Sub
60 Min., 1 Sub
Demand meter On The Hour
15 After Hour
30 After Hour
45 After Hour
Min/Max meter NO
YES
Min/Max meter 0 .. 1439 min
Min/Max meter 1 .. 365 Days
Min/Max meter 1 .. 365 Days
Measurem.Superv ON
OFF
Measurem.Superv 10 .. 100 V
Measurem.Superv 0.58 .. 0.95
Measurem.Superv 1A 0.10 .. 1.00 A
5A 0.50 .. 5.00 A
Measurem.Superv 0.10 .. 0.95
Measurem.Superv 1A 0.10 .. 2.00 A
5A 0.50 .. 10.00 A
Measurem.Superv 0.00 .. 0.95
Measurem.Superv 5 .. 100 sec
Measurem.Superv 5 .. 100 sec
Measurem.Superv ON
OFF
Measurem.Superv 10 .. 100 V
Measurem.Superv 1A 0.10 .. 1.00 A
5A 0.50 .. 5.00 A
Measurem.Superv 2 .. 100 V
Measurem.Superv 1A 0.05 .. 1.00 A
5A 0.25 .. 5.00 A
Measurem.Superv w/ CURR.SUP
w/ I> & 52a
OFF
Measurem.Superv 0.00 .. 30.00 sec
Measurem.Superv ON
OFF
Alarm only
Measurem.Superv ON
OFF
Measurem.Superv 1A 0.05 .. 1.00 A
5A 0.25 .. 5.00 A
79 Auto Recl. OFF
ON
79 Auto Recl. YES
NO
79 Auto Recl. 0.50 .. 300.00 sec
79 Auto Recl. 0.50 .. 300.00 sec; 0
79 Auto Recl. with PICKUP
with TRIP
Default Setting
60 Min., 1 Sub Demand Calculation Intervals
On The Hour Demand Synchronization Time
YES Automatic Cyclic Reset Function
0 min MinMax Reset Timer
7 Days MinMax Reset Cycle Period
1 Days MinMax Start Reset Cycle in
ON Measurement Supervision
50 V Voltage Threshold for Balance
Monitoring
0.75 Balance Factor for Voltage
Monitor
0.50 A Current Threshold for Balance
Monitoring
2.50 A
0.50 Balance Factor for Current
Monitor
0.25 A Summated Current Monitoring
Threshold
1.25 A
0.50 Summated Current Monitoring
Factor
5 sec T Balance Factor for Voltage
Monitor
5 sec T Current Balance Monitor
ON Fuse Failure Monitor
30 V Minimum Voltage Threshold V>
0.10 A Maximum Current Threshold I<
0.50 A
5 V Maximum Voltage Threshold V<
(3phase)
0.10 A Differential Current Threshold
(3phase)
0.50 A
w/ CURR.SUP Voltage Failure Supervision
3.00 sec Delay Voltage Failure Supervi-
sion
OFF Fast broken current-wire supervi-
sion
ON State of fast current summation
supervis
0.10 A Min. current diff. for wire break
det.
0.50 A
ON 79 Auto-Reclose Function
NO 52-ready interrogation at 1st trip
3.00 sec Reclaim time after successful AR
cycle
1.00 sec AR blocking duration after
manual close
with TRIP Evolving fault recognition
SIPROTEC, 7SD80, Manual
E50417-G1140-C474-A1, Release date 09.2011
Comments