Low Voltage Operation - Toshiba VF-S15 Instruction Manual

 Table of input terminal functions 3
Function
Code
No.
100 RS
101 RSN
104 FCHG
105 FCHGN
106 FMTB
107 FMTBN
108 CMTB
109 CMTBN
110 PWE
111 PWEN
120 FSTP1
121 FSTP1N
122 FSTP2
123 FSTP2N
134 TVS
135 TVSN
136 RSC
137 RSCN
140 SLOWF
141 SLOWFN
142 STOPF
143 STOPFN
144 SLOWR
145 SLOWRN
146 STOPR
147 STOPRN
11
148 to 151
152 MOT2
153 MOT2N
158 RES2
159 RES2N
200 PWP
201 PWPN
PRWP
202
203 PRWPN
*1: Factory specific coefficient parameters are manufacturer setting parameters. Do not change the value of these parameters.
*2: These functions are cannot be assigned to Always active function selection 1 to 3 (f104, f108, f110).
Note 1: Function No. that are not described in the table above are assigned "No function".
Function
Run/Stop command
Inversion of run/Stop command
Frequency setting mode forced switching
Inversion of frequency setting mode forced
switching
Frequency setting mode terminal block
Inversion of frequency setting mode terminal
block
Command mode terminal block
Inversion of command mode terminal block
Parameter editing permission
Inversion of parameter editing permission
Fast stop command 1
Inversion of fast stop command 1
Fast stop command 2
Inversion of fast stop command 2
Traverse permission signal
Inversion of traverse permission signal
Low voltage operation signal
Inversion of low voltage operation signal
Forward deceleration
Inversion of forward deceleration
Forward stop
Inversion of forward stop
Reverse deceleration
Inversion of reverse deceleration
Reverse stop
Inversion of reverse stop
Factory specific coefficient
No.2 motor switching
（AD2＋VF2＋OCS2）
Inversion of No.2 motor switching
（AD2＋VF2＋OCS2）
Reset command 2 *2
Inversion of reset command 2 *2
Parameter editing prohibition
Inversion of parameter editing prohibition
Parameter reading prohibition
Inversion of parameter reading prohibition
Action
ON: Run command
OFF: Stop command
Inversion of RS
ON: f207 (f200=0)
OFF: fmod
Inversion of FCHG
ON: Terminal block (VIA) enabled
OFF: Setting of 
Inversion of FMTB
ON: Terminal block enabled
OFF: Setting of 
Inversion of CMTB
ON: Parameter editing permitted
OFF: Setting of 
Inversion of PWE
ON: Dynamic quick deceleration command
OFF: Forced deceleration canceled
(Note that operation is resumed when forced deceleration is canceled)
Inversion of FSTP1
ON: Automatic deceleration
OFF: Forced deceleration canceled
(Note that operation is resumed when forced deceleration is canceled)
Inversion of FSTP2
ON: Permission signal of traverse operation
OFF: Normal operation
Inversion of TVS
ON: Low voltage operation
OFF: Low voltage operation canceled
Inversion of RSC
ON: Forward operation with f383 frequency
OFF: Normal operation
Inversion of SLOWF
ON: Forward stop, OFF: Normal operation
Inversion of STOPF
ON: Reverse operation with f383 frequency
OFF: Normal operation
Inversion of SLOWR
ON: Reverse stop, OFF: Normal operation
Inversion of STOPR
-
ON: No.2 motor
(=0, , , ,  (thr when
f632=2 or 3), , , , )
OFF: No.1 motor (Set value of , , , , ,
, , , )
Inversion of MOT2
ON: Trip reset
Inversion of RES2
ON: Parameter editing prohibited
OFF: Setting of 
Inversion of PWP
ON: Parameter reading / editing prohibited
OFF: Setting of 
Inversion of PRWP
K-32
E6581611
Reference
7.2.1
6.2.1
6.34.1
6.1.4
6.40
6.17
6.22.2
*1
6.8.1
13.2
6.34.1