Event Log; Enable/Disable Auto-Arm; Teleservice Request - Bentel Security Kyo 320 User Manual

+
You can Bypass a Zone using a 6-digit User Code
PIN, as follows: — type in a valid 6-digit User Code
PIN followed by the 3-digit ID number of the Zone
concerned then press ESC. For example, if the
PIN is 135790 and you want to Bypass Zone 23,
type in 135790 023 then press ESC.
n Event Log
This command will allow you to view and print the
events in the Event Log. The Control panel Event log
can store up to 10,000 events. The events will be stored
in chronological order —starting from the most recent.
Each event shows the following details:
ØEv. (Event number)
ØTYPE (e.g. Zone Alarm, Invalid Code, etc.)
ØIDENT (e.g. Zone number, Partition, etc.)
ØAGENT (e.g. Keypad, Reader, etc.)
ØID.AGEN (e.g. User code, Card/Key, etc.)
ØTIME (Time and Date of the event)
The display will show the following message:
EVENT LOGGER
From Last ...
To view all Events
Press the ENTER key to view all the Events in the
Log—starting from the most recent (from last . . ).
Use A and B to scroll the Events.
Press D to view the Event details (see above).
To view Events from a specific Date
EVENT LOGGER
starting from..
Using A or B scroll for the following message:
Press the ENTER key, the display will show the Date
prompt.
Starting from..
10/09/2006
Enter all the digits of the required Date (DD/MM/YYYY),
then press the ENTER key.
Use A and B to scroll the Events.
Press D to view the Event details (see above).
Ev.00015 TYPE
Valid code
+
The display will show the relevant details for each
Event. For example, Tamper Events show the
TYPE and TIME only.
To print Events from a specific Date
Using A or B scroll for the following message:
EVENT LOGGER
print from..
KYO320 OPERATING YOUR SYSTEM FROM A KEYPAD
Press the ENTER key, the display will show the Date
prompt.
Starting from...
10/09/2005
Enter all the digits of the required Date (DD/MM/YYYY),
then press the ENTER key.
The Keypad will exit the USER MENU, and the Printer
will print the Events starting from the entered date to the
most recent.
+
This facility is provided by the optional K3-PRT2
Printer Interface (ask your Installer for details).
The Event Log
The Event log is set up as follows:
Ø the Event number (Ev.) is shown on the left side of
the first line;
Øthe Event details (TYPE, IDENT., USER, USER ID,
TIME) are shown on the second line.
Ev.00015 TYPE
Valid code
Using the Event Log:
Ø Use A and B to scroll the Events.
Ø Press D to view the Event details (see above).
ØPress the e to step back to the Event Log menu.
+
The display will show the relevant details for each
Event. For example, Tamper Events show the
TYPE and TIME only.
n Enable/Disable Auto-arm
Your Installer may have set up Partitions to turn
ON/OFF at preset times. This command will allow you
to turn the Scheduler ON/OFF, and Enable/Disable au-
tomatic ON/OFF control.
Use A and B to scroll the Partitions, and the ON and
OFF keys to Enable/Disable the Scheduler.
Partition 001
Scheduler OFF
Press the ESC key to step back to the User menu.
n Teleservice request
If your Installer has set up this facility, this command will
allow you to request on-line assistance (maintenance
that does not require components or wiring). Teleservi-
ce requests will be confirmed by the following message:
USER MENU
done!
The Teleservice request will stop any ongoing Telephone
calls (Teleservice requests from the User have priority
over other call types), and will send the Teleservice call (or
calls) to the Installer telephone number (or numbers).
11