Enable/Disable Teleservice; Enable/Disable Answering Device; Activating Outputs (Turning On/Off Appliances); Clear Call Queue - Bentel Security Kyo 320 User Manual

n Enable/Disable Teleservice
This command will allow you to Enable/Disable the
Control panel to receive Teleservice calls. The com-
mand will be confirmed by the following message:
En./Dis. Service
Service OFF
ON to enable procedures with the installer code
OFF to disable procedures with the installer code
Press the ENTER button to confirm and return to the
User menu.
If the user enables the Maintenance mode (Maintenan-
ce ON) and the control unit is connected to the telepho-
ne line, the installer will be able to perform the following
procedures remotely, as well as on site:
Ø View the Control panel status — Partition status;
Alarm memory, Bypassed zones, Zone status, Event
logger, Peripheral device status, etc.
Ø Change the Control panel status — Change Par-
tition status, Clear the Alarm memory and Bypass
zones (active User Code required).
Ø Change the Control panel parameters — if all the
partitions are disarmed and the Partition Patrol Times
are not active.
The Teleservice facility allows the Installer to check and
work on the Control panel from a remote computer, and
carry out maintenance work that does not require new
wiring or components.
+
An * will be shown on the display directly above
the t when the Teleservice facility is enabled.
n Enable/Disable Answering device
This command will allow you to turn ON/OFF the
Answering device. If the Answering device is ON, the
Control panel will answer incoming calls with a Voice
message. This facility is provided by the K3-VOX2 Voi-
ce board (accessory item).
The Answering device can function even if the
K3-VOX2 Voice board is absent, but in this case there
aren't voice messages.
mand, the display will show the following message:
En./Dis.Ans.Dev.
Answer dev. OFF
Press ON to Enable the Answering device facility.
Press OFF to Disable the Answering device facility.
Press the ENTER key to confirm and step back to the User
menu.
+
If the Answering device facility is enabled, an * will
be shown on the display directly above the r.
n Activating Outputs (Turning ON/OFF
Appliances)
If your Installer has set up your system to control ap-
pliances (sprinklers, lights, etc.), this command will al-
low you to turn the appliances ON/OFF manually.
12
When you select this com-
To turn ON/OFF Outputs (appliances):
1. Use A and B to scroll the list.
Output n. 001
Output 001
2. Press the ENTER key to select the required Output
(appliance). The display will show the current status.
Output 001
INACTIVE
3. Press ON or OFF, as required.
Use A and B to continue scrolling the list.
4.Press the ESC key twice to confirm and step back to
the User menu.
n Clear call queue
If your Installer has programmed your Control panel to
send Alarm calls, it will call the programmed telephone
numbers each time an Alarm occurs. In the event of a
False Alarm, this command will allow you to interrupt
the ongoing call, and clear the call queue.
If you select this command the display will show the fol-
lowing message:

CLEAR CALL QUEUE

Confirm?
To confirm the Command
Press the ENTER key.
The display will show the following message for several
seconds before stepping back to the User menu:
CLEAR CALL QUEUE
done!
To Abort the Command
Press the ESC key to step back to the User menu.
n Overtime request
If the Auto-arm option is enabled, and the system is pro-
grammed to Arm automatically at a preset time, the
Overtime request will allow you to delay the Auto-ar-
ming event.
Acceptance of the Overtime Request will be confirmed
by an audible feed back signal and the following
message:

OVERTIME REQUEST

done!
+
If any of the Partitions concerned is unable to im-
plement the Overtime request, the Keypad will emit
an audible error signal.
The Installer will set up the Auto-arm and Overtime Re-
quest events with your installation in mind, and will pro-
vide you with all the necessary information (regarding
KYO320