Mitsubishi FX3U-?*MR/ES User Manual page 484

FX Series Programmable Controllers
3U
User's Manual - Hardware Edition
Number and
Operation and function
name
High-Speed Counter Comparison, High-Speed Table, and Positioning
HSZ (FNC 55) instruction:
M 8130
Table comparison mode
HSZ (FNC 55) instruction:
[M]8131 Table comparison mode
completion flag
HSZ (FNC 55) and PLSY (FNC 57)
M 8132
instructions: Speed pattern mode
HSZ (FNC 55) and PLSY (FNC 57)
instructions:
[M]8133
Speed pattern mode completion
flag
[M]8134
[M]8135
Not used
[M]8136
[M]8137
HSCT (FNC280) instruction:
[M]8138
Instruction execution complete flag
HSCS(FNC 53), HSCR(FNC 54),
HS2(FNC 55), HSCT(FNC280)
[M]8139 instructions:
High-speed counter comparison
instruction executing
ZRN (FNC156) instruction:
M 8140
CLR signal output function enable
[M]8141
[M]8142
[M]8143
[M]8144
M 8145 Not used
M 8146
[M]8147
[M]8148
[M]8149
Inverter Communication Function
[M]8150 Not used
Inverter communication in
[M]8151
execution [ch1]
*1
Inverter communication error [ch1]
[M]8152
Inverter communication error latch
*1
[M]8153
[ch1]
IVBWR (FNC274) instruction error
*1
[M]8154
[ch1]
[M]8155 Not used
Inverter communication in
[M]8156
execution [ch2]
*1
Inverter communication error [ch2]
[M]8157
Inverter communication error latch
*1
[M]8158
[ch2]
IVBWR (FNC274) instruction error
*1
[M]8159
[ch2]
*1. Cleared when PLC switches from STOP to RUN.
476
A Operation of Special Devices (M8000 -, D8000 -)
Correspond-
Number and
ing special
name
device
Advanced Function
*2
M 8160
*2*3
M 8161
D8130
M 8162
[M]8163
M 8164
*2
M 8165
D8131 to
D8134
[M]8166
*2
M 8167
–
*2
–
M 8168
–
[M]8169
–
*2. Cleared when PLC switches from RUN to STOP.
D8138
*3. Applicable to ASC (FNC 76), RS (FNC 80), ASCI (FNC
82), HEX (FNC 83), CCD (FNC 84), and CRC (FNC188)
instructions.
D8139
Pulse Catch
*4
M 8170
–
*4
M 8171
–
*4
M 8172
–
*4
M 8173
–
*4
M 8174
–
*4
M 8175
–
*4
–
M 8176
–
*4
M 8177
–
*4. Cleared when PLC switches from STOP to RUN.
–
EI (FNC 04) instruction is necessary.
–
Communication Port Channel Setting
D8151
M 8178
D8152
M 8179
D8153
*5. The channel is specified by either creating or not creating
M8179 in setting program.
D8154
•ch1: not creating M8179 in setting program
•ch2: creating M8179 in setting program
–
D8156
D8157
D8158
D8159
A-1 Special Auxiliary Relay (M8000 to M8511)
Operation and function
SWAP function of XCH (FNC 17)
8-bit process mode
High-speed parallel link mode
Not used
SORT2 (FNC149) instruction:
Sorting in descending order
Not used
HKY (FNC 71) instruction:
HEX data handling function
SMOV (FNC 13) instruction:
HEX data handling function
Not used
Input X000 pulse catch
Input X001 pulse catch
Input X002 pulse catch
Input X003 pulse catch
Input X004 pulse catch
Input X005 pulse catch
Input X006 pulse catch
Input X007 pulse catch
Parallel link channel switch (OFF:
ch1/ON: ch2)
N:N network channel switch
Correspond-
ing special
device
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
*5
–