Cable Assembly - Pro-Form PFEMSY75000 User Manual

6. See the inset drawing. Press two Weight Inserts (77)
into the indicated holes in each Weight (26). Make
sure the large pin groove is oriented as shown.
Slide all of the included Weights (26) onto the two
Weight Guides (23). Make sure the Weights are ori-
ented correctly. The holes must be turned
towards the front of the unit, as shown.
Slide the Top Weight (16) with the pre-attached
Weight Tube (36) onto the Weight Guides (23). The
Weight Tube slides into the hole in the centre of the
Weights (26).
Place the Top Frame (1) over the Weight Guides (23),
so the Weight Guides fit into the welded tubes on the
Top Frame.
Align the bracket on the Top Frame (1) with the holes
in the Main Upright (3). Insert two 3/8" x 3" Bolts (45)
through the holes. Tighten a 3/8" Nylon Locknut (50)
onto the lower of the two Bolts. Do not mount a
Locknut on the upper Bolt yet.
Attach the Weight Guides (23) to the Top Frame (1)
with two 3/8" x 1 3/4" Bolts (60) and two 3/8" Nylon
Locknuts (50). Go back and fully tighten all Nylon
Locknuts used in steps 1, 2 and 6.

Cable Assembly

7. Locate and open the parts bag labelled "CABLE
ASSEMBLY." Refer to the Cable Diagram on page
16 as you assemble the Cables.
Identify the High Cable (73). It is approximately 188"
long (the shortest Cable), and it has a ball on one
end and a bolt on the other.
Locate the end of the High Cable (73) with the bolt.
Feed this end through the indicated slot in the Main
Upright (3) from below. Feed almost all of the Cable
through the slot.
Slide a 3/8" Flat Washer (55) and a Pulley Bushing
(42) onto a 3/8" x 2 1/2" Bolt (54).
Wrap the High Cable (73) around a 4" Pulley (35) and
slide both Pulley and Cable into the slot in the Main
Upright (3). While holding the Pulley with one hand,
insert the 3/8" x 2 1/2" Bolt (54) through the hole in
the Main Upright, through the Pulley and through the
other side of the Upright.
Slide a Pulley Bushing (42) and a 3/8" Flat Washer
(55) onto the 3/8" x 2 1/2" Bolt (54). Then tighten a
3/8" Nylon Jamnut (63) onto the Bolt.
6 1
50 45
50
60
Welded
Tubes
3
23
16
77
36
26
Large Pin
Holes
Groove
7
Bolt
Slot
73
35
42
55
Ball
63
42
3
8
Arm Assembly
20. Note: Some of the parts used in arm assembly are
located in the parts bag labelled "Seat Assembly."
Attach the Press Arm (46) to the Press Frame (12)
with two 3/8" x 3" Bolts (45) and two 3/8" Nylon
Locknuts (50).
21. Press a 2" Square Inner Cap (33) into each end of
the Press Arm (46).
26
Insert a Handle (20) into the indicated hole on one
side of the Press Arm (46) from the direction shown.
Note that on one side the Handle has a groove
with a series of adjustment holes (A). These holes
must be turned towards the Adjustment Knob (9).
Make sure the Grip (58) is pointed towards the
centre of the unit on both Handles.
Unscrew the handle on the Adjustment Knob (9) and
pull it out. Slide the press arm Handle (20) into the
Press Arm. Release the handle on the Adjustment
Knob and let it snap into one of the adjustment holes
54
(A). Tighten the handle on the Adjustment Knob fully.
Repeat this procedure for the second Handle.
Seat Assembly
55
22. Attach the Seat (13) to the Seat Upright (37) with four
1/4" x 3/4" Bolts (17).
Unscrew the handle on the Adjustment Knob (9) until
it is loose. Pull out the handle as far as it will go and
slide the Seat Upright (37) into the seat frame on the
Main Upright (3). Release the handle and let the
Knob snap into one of the adjustment holes on the
Seat Upright. Tighten the handle fully.
20
12
50
50
45
21
9
A
46
9
58
58
A
33
20 Hole
22
13
3
37
17
17
Adjustment
Holes
9
13
46
33