Cable Assembly - Pro-Form PFEMSY75001 User Manual

6. See the inset drawing. Press two Weight Inserts (77)
into the indicated holes in each Weight (26). Make
sure the large pin groove is oriented as shown.
Slide all of the included Weights (26) onto the two
Weight Guides (23). Make sure the Weights are ori-
ented correctly. The holes must be turned
towards the front of the unit, as shown.
Slide the Top Weight (16) with the pre-attached
Weight Tube (36) onto the Weight Guides (23). The
Weight Tube will slide into the hole in the centre of
the Weights (26).
Place the Top Frame (1) over the Weight Guides (23),
so the Weight Guides fit into the welded tubes on the
Top Frame.
Align the bracket on the Top Frame (1) with the holes
in the Main Upright (3). Insert two 3/8" x 3" Bolts (45)
through the holes. Tighten a 3/8" Nylon Locknut (50)
onto the lower of the two Bolts. Do not mount a
Locknut on the upper Bolt yet.
Attach the Weight Guides (23) to the Top Frame (1)
with two 3/8" x 1 3/4" Bolts (60) and two 3/8" Nylon
Locknuts (50). Go back and fully tighten all Nylon
Locknuts used in steps 1, 2, and 6.

Cable Assembly

7. Locate and open the parts bag labelled "CABLE
ASSEMBLY." Refer to the CABLE DIAGRAM on
page 16 as you assemble the cables.
Identify the High Cable (73). It is the shortest cable
(about 477cm long) and it has a ball on one end and
a bolt on the other.
Insert the end of the High Cable (73) with the bolt up
through the indicated slot in the Main Upright (3).
Feed almost all of the Cable through the slot.
Slide a 3/8" Flat Washer (55) and a Pulley Bushing
(42) onto a 3/8" x 2 1/2" Bolt (54).
Wrap the High Cable (73) around a 4" Pulley (35) and
hold the Pulley in the slot in the Main Upright (3).
Insert the 3/8" x 2 1/2" Bolt (54) through the Main
Upright and the Pulley.
Slide another Pulley Bushing (42) and another 3/8"
Flat Washer (55) onto the 3/8" x 2 1/2" Bolt (54) and
tighten a 3/8" Nylon Jamnut (63) onto the Bolt.
6
45
1
50
50
60
Welded
Tubes
3
23
16
77
36
26
Large Pin
Holes
Groove
7
Bolt
Slot
73
35
42
55
Ball
63
42
3
8
Arm Assembly
20. Note: Some parts used in this section are located
in the parts bag labelled "SEAT ASSEMBLY."
Attach the Press Arm (46) to the Press Frame (12)
with two 3/8" x 3" Bolts (45) and two 3/8" Nylon
Locknuts (50).
26
21. Press a 2" Square Inner Cap (33) into each end of
the Press Arm (46).
Unscrew one of the Adjustment Knobs (9) on the
Press Arm (46) and pull it out as far as it will go.
Slide the Handle (20) into the Press Arm with the
groove toward the Adjustment Knob. Release the
Adjustment Knob and let it snap into an adjustment
hole in the Handle. Fully tighten the Adjustment
Knob.
Attach the other Handle (20) in the same manner.
54
Seat Assembly
55
22. Attach the Seat (13) to the Seat Upright (37) with four
1/4" x 3/4" Bolts (17).
Unscrew the handle on the Adjustment Knob (9) until
it is loose. Pull out the handle as far as it will go and
slide the Seat Upright (37) into the seat frame on the
Main Upright (3). Release the handle and let the
Knob snap into one of the adjustment holes on the
Seat Upright. Tighten the handle fully.
20
12
50
50
45
21
9
46
9
20
33
Hole
22
13
3
37
17
17
Adjustment
Holes
9
13
46
33