Page 1 LTE3311 Series LTE Indoor IAD Version 1.00 Edition 1, 02/2016 Quick Start Guide User’s Guide Default Login Details LAN IP Address http://192.168.1.1 User Name admin www.zyxel.com Password 1234 Copyright © 2016 ZyXEL Communications Corporation...
Page 2 The Quick Start Guide shows how to connect the LTE3311 and access the Web Configurator wizards. It contains information on setting up your network and configuring for Internet access. • More Information Go to support.zyxel.com to find other information on the LTE3311. LTE3311 Series User’s Guide...
Page 3: Table Of Contents
Firewall ..............................107 Content Filtering ............................ 112 IPv6 Firewall ............................115 Voice over IP ............................117 Voice over 3G ............................136 SMS ..............................140 NAS ...............................143 Bandwidth Management ........................150 Universal Plug-and-Play (UPnP) ......................154 TR-069 ..............................160 Maintenance ............................162 Troubleshooting ............................170 LTE3311 Series User’s Guide...
Page 4: Table Of Contents
2.2.1 Login Screen ...........................19 2.2.2 Password Screen ........................20 2.3 The Main Screen ..........................21 2.3.1 Title Bar ...........................22 2.3.2 Navigation Panel ........................22 2.4 Status Screen ............................25 Chapter 3 Setup Wizard ............................29 3.1 Overview ............................29 3.2 Accessing the Wizard ........................29 LTE3311 Series User’s Guide...
Page 5 6.3 What You Need To Know ........................54 6.4 Management WAN ...........................56 6.4.1 Management WAN Edit ......................57 6.5 Network Scan ............................60 6.6 IPv6 ..............................62 6.7 PIN Management ..........................63 Chapter 7 Wireless LAN............................64 7.1 Overview ............................64 7.1.1 What You Can Do ........................65 LTE3311 Series User’s Guide...
Page 6 10.1 Overview ............................91 10.1.1 What You Can Do ........................91 10.2 General Screen ..........................92 10.3 Port Forwarding Screen .........................92 10.3.1 Port Forwarding Edit Screen ....................94 10.4 Port Trigger Screen .........................95 10.5 ALG Screen .............................96 10.6 Technical Reference ........................97 LTE3311 Series User’s Guide...
Page 7 Content Filtering ..........................112 15.1 Overview ............................112 15.2 Content Filter ..........................112 Chapter 16 IPv6 Firewall ............................115 16.1 Overview ............................115 16.2 IPv6 Firewall Screen ........................115 Chapter 17 Voice over IP ............................. 117 LTE3311 Series User’s Guide...
Page 8 20.1.2 What You Need To Know .....................143 20.1.3 Before You Begin .........................143 20.2 File Sharing ...........................144 20.2.1 Filing Sharing Screen ......................144 20.3 FTP Screen ...........................145 20.3.1 Example of Accessing Your Shared Files From a Computer ..........146 Chapter 21 Bandwidth Management........................150 LTE3311 Series User’s Guide...
Page 9 24.8 Restart Screen ..........................169 Chapter 25 Troubleshooting..........................170 25.1 Overview ............................170 25.2 Power, Hardware Connections, and LEDs ..................170 25.3 LTE3311 Access and Login ......................171 25.4 Internet Access ..........................172 25.5 Wireless Connections ........................173 25.6 Getting More Troubleshooting Help ....................174 LTE3311 Series User’s Guide...
Page 10 Table of Contents Appendix A Customer Support ......................175 Appendix B Pop-up Windows, JavaScript and Java Permissions ...........181 Appendix C Setting Up Your Computer’s IP Address ..............190 Appendix D Common Services......................216 Appendix E Legal Information......................219 Index ..............................227 LTE3311 Series User’s Guide...
Page 11: User's Guide
User’s Guide...
Page 12: Introduction
You can use WPS (Wi-Fi Protected Setup) to create an instant network connection with another WPS-compatible device. • Wireless WAN. Insert a 3G/4G SIM card into the SIM card slot to connect to a mobile network for Internet access. LTE3311 Series User’s Guide...
Page 13: Wireless Wan (3G/4G) Connection
Use the built-in USB 2.0 port to share files on a USB memory stick or a USB hard drive (B). You can connect one USB hard drive to the LTE3311 at a time. Use FTP to access the files on the USB device. LTE3311 Series User’s Guide...
Page 14: Ways To Manage The Lte3311
RESET button at the back of the LTE3311 to reload the factory-default configuration file. This means that you will lose all configurations that you had previously saved, the password will be reset to “1234” (see Section 24.4 on page 163) and the IP address will be reset to “192.168.1.1”. LTE3311 Series User’s Guide...
Page 15: How To Use The Reset Button
3G/4G module, just insert a 3G/4G SIM card into the SIM card slot at the back of the LTE3311. Note: You must insert the 4G SIM card into the card slot before turning on the LTE3311. LTE3311 Series User’s Guide...
Page 16: Leds
-81 dBm >= RSRP >= -95 dBm One bar: Signal strength: Poor -97 dBm > RSRP Blinking There is no LTE signal because there is no valid SIM card inserted and/or the wireless WAN interface is disabled. LTE3311 Series User’s Guide...
Page 17: Wall Mounting
- leave a small gap of about 0.5 cm. If not using screw anchors, use a screwdriver to insert the screws into the wall. Do not insert the screws all the way in - leave a gap of about 0.5 cm. LTE3311 Series User’s Guide...
Page 18 Make sure the screws are fastened well enough to hold the weight of the LTE3311 with the connection cables. Align the holes on the back of the LTE3311 with the screws on the wall. Hang the LTE3311 on the screws. Figure 2 Wall Mounting Example LTE3311 Series User’s Guide...
Page 19: Introducing The Web Configurator
Launch your web browser. Type "http://192.168.1.1" as the website address. Your computer must be in the same subnet in order to access this website address. 2.2.1 Login Screen The Web Configurator initially displays the following login screen. LTE3311 Series User’s Guide...
Page 20: Password Screen
Type "admin" (default) as the user name. Password Type "1234" (default) as the password. Click Login. 2.2.2 Password Screen You should see a screen asking you to change your password (highly recommended) as shown next. Figure 4 Change Password Screen LTE3311 Series User’s Guide...
Page 21: The Main Screen
2.3 The Main Screen The Web Configurator’s main screen is divided into these parts: Figure 5 The Web Configurator’s Main Screen • A - Title Bar • B - Navigation Panel • C - Main Window LTE3311 Series User’s Guide...
Page 22: Title Bar
Click this icon to open a screen where you can click a link to visit the ZyXEL web site to see detailed product information. Logout Click this icon to log out of the Web Configurator. 2.3.2 Navigation Panel Use the sub-menus on the navigation panel to configure LTE3311 features. Figure 7 Navigation Panel LTE3311 Series User’s Guide...
Page 23 Use this screen to assign IP addresses to specific individual computers based on their MAC addresses and to have DNS servers assigned by the DHCP server. Client List Use this screen to view information related to your DHCP status. LTE3311 Series User’s Guide...
Page 24 Use this screen to set the upstream bandwidth and edit a bandwidth management rule. UPnP UPnP Use this screen to enable UPnP on the LTE3311. TR069 TR069 Use this screen to configure your LTE3311 to be managed by an ACS. LTE3311 Series User’s Guide...
Page 25: Status Screen
Use this screen to backup and restore the configuration or reset the factory Restore Restore defaults to your LTE3311. Restart System This screen allows you to reboot the LTE3311 without turning the power Restart off. 2.4 Status Screen Click to open the status screen. Figure 8 Status Screen LTE3311 Series User’s Guide...
Page 26 This shows the channel number which you select manually. System This shows the wireless standards the LTE3311 supports. Security This shows the level of wireless security the LTE3311 is using. Firewall This shows whether the firewall is enabled or not. LTE3311 Series User’s Guide...
Page 27 2.4G WLAN is disabled. For the USB port, it displays Up when the LTE3311 detects a USB connection or Down when there is no USB device attached or the LTE3311 does not detect a USB connection. LTE3311 Series User’s Guide...
Page 28 This displays the account number and service domain of the SIP account. You can change these in the Application > Voice over IP > SIP Conf. > Service Domain Conf. screens. Message Waiting This field indicates whether or not there are any messages waiting for the SIP account. LTE3311 Series User’s Guide...
Page 29: Setup Wizard
Click the Wizard icon in the top right corner of the web configurator to open the Wizard screen. Figure 9 Title Bar: Wizard icon 3.3 Wizard Setup The first wizard screen displays showing the main steps in the wizard setup. Click Next to proceed with the time zone setup screen. LTE3311 Series User’s Guide...
Page 30 Detect Again or manually select the time zone of LTE3311’s location and click Next. Figure 11 Wizard: Time Enter your APN (Access Point Name) provided by your service provider. Select the country where the LTE3311 is located and your service provider name. Click Next. LTE3311 Series User’s Guide...
Page 31 The wireless clients which want to associate with this wireless network must have the same wireless security settings. Otherwise, select No Security to allow any client to associate with this network without any data encryption or authentication. Click Next. LTE3311 Series User’s Guide...
Page 32 Use the read-only summary table to check whether what you have configured is correct. Click Apply Settings to save your settings. Otherwise, click Back to go back to the previous screens. Figure 15 Wizard: Summary The system takes about 35 seconds to apply settings. LTE3311 Series User’s Guide...
Page 33 Chapter 3 Setup Wizard Figure 16 Wizard: Apply Settings Click Finish to complete the wizard setup. Figure 17 Wizard: Finish You are now ready to connect wirelessly to your LTE3311 and access the Internet. LTE3311 Series User’s Guide...
Page 34: Tutorials
In the wireless client utility, find the WPS settings. Enable WPS and press the WPS button (Start or WPS button). Log into LTE3311’s Web Configurator and press the Push Button in the Configuration > Network > Wireless LAN 2.4G > WPS Station screen. LTE3311 Series User’s Guide...
Page 35: Pin Configuration
Launch your wireless client’s configuration utility. Go to the WPS settings and select the PIN method to get a PIN number. Enter the PIN number to the PIN field in the Configuration > Network > Wireless LAN > WPS Station screen on the LTE3311. LTE3311 Series User’s Guide...
Page 36: Connect To Lte3311 Wireless Network Without Wps
This example shows you how to configure wireless security settings with the following parameters on your LTE3311 and connect your computer to the LTE3311 wireless network. SSID SSID_Example3 Channel Security WPA2-PSK (Pre-Shared Key: ThisismyWPA-PSKpre-sharedkey) Follow the steps below to configure the wireless settings on your LTE3311. LTE3311 Series User’s Guide...
Page 37 Confirm that the wireless LAN is enabled on the LTE3311. Enter SSID_Example3 as the SSID and select Channel-06 as the channel. Set security mode to WPA2-PSK and enter ThisismyWPA-PSKpre-sharedkey in the Pre-Shared Key field. Click Apply. LTE3311 Series User’s Guide...
Page 38: Configure Your Notebook
Wireless adapters come with software sometimes called a “utility” that you install on your computer. See your wireless adapter’s User’s Guide for information on how to do that. LTE3311 Series User’s Guide...
Page 39 View Available Wireless Networks. The Wireless Network Connection screen displays. Click Refresh network list to view the available wireless APs within range. Select SSID_Example3 and click Connect. Type the security key in the following screen. Click Connect. LTE3311 Series User’s Guide...
Page 40: Using Multiple Ssids On The Lte3311
Clients can associate only with the SSIDs for which they have the correct security settings. Clients using different SSIDs can access the Internet and the wired network behind the LTE3311 (such as a printer). LTE3311 Series User’s Guide...
Page 41: Configuring Security Settings Of Multiple Ssids
“http://192.168.1.1” as the web address in your web browser. Enter “admin” as the user name and “1234” (default) as the password and click Login. Type a new password and retype it to confirm, then click Apply. Otherwise, click Ignore. LTE3311 Series User’s Guide...
Page 42 Click Apply. Click the Edit icon of the second entry to configure wireless and security settings for SSID_VoIP. 10 Configure the screen as follows. You do not enable Intra-BSS Traffic for SSID_VoIP. Click Apply. LTE3311 Series User’s Guide...
Page 43 11 Click the Edit icon of the third entry to configure wireless and security settings for SSID_Guest. 12 Configure the screen as follows. In this example, you enable Intra-BSS Traffic for SSID_Guest to allow wireless clients in the same wireless network to communicate with each other. Click Apply. LTE3311 Series User’s Guide...
Page 44 Chapter 4 Tutorials LTE3311 Series User’s Guide...
Page 45: Technical Reference
Technical Reference...
Page 46: Monitor
SIM card. You can also check the LTE connection status (Section 5.7 on page 50). 5.3 The Log Screens The Web Configurator allows you to look at all of the LTE3311’s logs in one location. LTE3311 Series User’s Guide...
Page 47: View Log
You can configure which logs to display in the View Log screen. Go to the Log Setting screen and select the logs you wish to display. Click Apply to save your settings. Click Cancel to start the screen afresh. Figure 21 Log Settings LTE3311 Series User’s Guide...
Page 48: Dhcp Table
Click Monitor > Packet Statistics or the Packet Statistics (Details...) hyperlink in the Status screen. Read-only information here includes port status, packet specific statistics and the "system up time". The Poll Interval(s) field is configurable and is used for refreshing the screen. LTE3311 Series User’s Guide...
Page 49: Wlan Station Status
Association List. Association means that a wireless client (for example, your network or computer with a wireless network card) has connected successfully to the AP (or wireless router) using the same SSID, channel and security settings. LTE3311 Series User’s Guide...
Page 50: Lte Modem Status
Figure 25 Monitor > LTE Modem Status The following table describes the labels in this screen. Table 12 Monitor > LTE Modem Status LABEL DESCRIPTION Modem Information Physical Interface This displays the interface used for the mobile data connection. LTE3311 Series User’s Guide...
Page 51 This displays the number for Short Message Service Center (SMSC), which stores, forwards and delivers SMS text message. MSISDN This displays the MSISDN (Mobile Subscriber ISDN) number, a phone number assigned to a mobile subscriber to call a mobile device. LTE3311 Series User’s Guide...
Page 52 This displays the MIMO (Multi-input Multi-output) technology supported by the LTE3311, such as 1T2R (1 Transmit and 2 Receive paths/antennas) or TM1-TM4 (Transmission Mode 4). Support Band List This displays the frequency bands that are supported by the LTE3311. LTE3311 Series User’s Guide...
Page 53: Wan
60). • Use the IPv6 screen to configure the LTE3311’s IPv6 settings (Section 6.6 on page 62). • Use the PIN Management screen to configure the LTE3311’s PIN settings (Section 6.7 on page 63). LTE3311 Series User’s Guide...
Page 54: What You Need To Know
If your ISP gives you DNS server addresses, manually enter them in the DNS server fields. If your ISP dynamically assigns the DNS server IP addresses (along with the LTE3311’s WAN IP address), set the DNS server fields to get the DNS server address from the ISP. LTE3311 Series User’s Guide...
Page 55 • Any number of consecutive blocks of zeros can be replaced by a double colon. A double colon can only appear once in an IPv6 address. So 2001:0db8:0000:0000:1a2f:0000:0000:0015 can be written as 2001:0db8::1a2f:0000:0000:0015, 2001:0db8:0000:0000:1a2f::0015, 2001:db8::1a2f:0:0:15 or 2001:db8:0:0:1a2f::15. LTE3311 Series User’s Guide...
Page 56: Management Wan
IPv6 Internet IPv6 in IPv4 IPv4 IPv6 IPv4 IPv4 Internet 6.4 Management WAN The summary table shows you the WAN connection configured on the LTE3311. Click Network > WAN > Management WAN from the Configuration menu. LTE3311 Series User’s Guide...
Page 57: Management Wan Edit
Click the Edit icon to configure the WAN connection settings. 6.4.1 Management WAN Edit Use this screen to change your LTE3311’s 3G/4G WAN connection settings. Click the Edit icon in the Network > WAN > Management WAN screen. LTE3311 Series User’s Guide...
Page 58 Select Auto-Detection to have the LTE3311 use the inserted SIM card’s default settings to connect to any available mobile network. Select Manual and enter the information provided by your service provider to connect to the service provider’s mobile network. LTE3311 Series User’s Guide...
Page 59 WAN connection within a time period specified in the Check Interval field. Check Interval Type a number of seconds (0 to 99999) to set the time interval between checks. Allow more time if your destination IP address handles lots of traffic. LTE3311 Series User’s Guide...
Page 60: Network Scan
Click More to display advanced fields. 6.5 Network Scan Use this screen to set how you want the LTE3311 to connect to an available mobile network. Click Network > WAN > Network Scan from the Configuration menu. LTE3311 Series User’s Guide...
Page 61 Click Select to have the LTE3311 establish a connection to the selected mobile network. Apply Click Apply to save your changes back to the LTE3311. Cancel Click Cancel to reload the previous configuration for this screen. Refresh Click Refresh to update this screen. LTE3311 Series User’s Guide...
Page 62: Ipv6
Autoconfiguration Type Select Stateless if you want the LTE3311 interface to automatically generate a link- local address via stateless autoconfiguration. Select Stateful (DHCPv6) when the devices connected to your LAN needs to have their TCP/IP configuration set to DHCPv6 or obtain an IPv6 address automatically. LTE3311 Series User’s Guide...
Page 63: Pin Management
If you select Enable, enter the 4-digit PIN code (0000 for example) provided by your ISP for the inserted SIM card. Apply Click Apply to save your changes back to the LTE3311. Cancel Click Cancel to reload the previous configuration for this screen. LTE3311 Series User’s Guide...
Page 64: Wireless Lan
The wireless network is the part in the blue circle. In this wireless network, devices A and B are called wireless clients. The wireless clients use the access point (AP) to interact with other devices (such as the printer) or with the Internet. Your LTE3311 is the AP. LTE3311 Series User’s Guide...
Page 65: What You Can Do
SSID to something that is difficult to guess. This type of security is fairly weak, however, because there are ways for unauthorized devices to get the SSID. In addition, unauthorized devices can still see the information that is sent in the wireless network. LTE3311 Series User’s Guide...
Page 66: Mac Address Filter
Some wireless devices, such as scanners, can detect wireless networks but cannot use wireless networks. These kinds of wireless devices might not have MAC addresses. Hexadecimal characters are 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, and F. LTE3311 Series User’s Guide...
Page 67: General Wireless Lan Screen
Number) in the devices. Then, they connect and set up a secure network by themselves. See how to set up a secure wireless network using WPS in the Section 4.2 on page 7.2 General Wireless LAN Screen Use this screen to configure the SSID and wireless security of the wireless LAN. LTE3311 Series User’s Guide...
Page 68 Select this check box for the LTE3311 to automatically choose the channel with the least Selection interference. Deselect this check box if you wish to manually select the channel using the Channel Selection field. Operating This displays the channel the LTE3311 is currently using. Channel LTE3311 Series User’s Guide...
Page 69: Wireless Security
7.3 Wireless Security The screen varies depending on what you select in the Security Mode field. 7.3.1 No Security Select No Security to allow wireless clients to communicate with the access points without any data encryption. LTE3311 Series User’s Guide...
Page 70: Wep Encryption
Both the wireless stations and the access points must use the same WEP key. Your LTE3311 allows you to configure up to four 64-bit or 128-bit WEP keys but only one key can be enabled at any one time. Select Static WEP from the Security Mode list. LTE3311 Series User’s Guide...
Page 71 Select this option in order to enter ASCII characters as WEP key. Select this option in order to enter hexadecimal characters as a WEP key. The preceding "0x", that identifies a hexadecimal key, is entered automatically. LTE3311 Series User’s Guide...
Page 72: Wpa-Psk/Wpa2-Psk
Select WPA-PSK or WPA2-PSK to enable data encryption. WPA-PSK This field appears when you choose WPA2-PSK as the Security Mode. Compatible Check this field to allow wireless devices using WPA-PSK security mode to connect to your LTE3311. LTE3311 Series User’s Guide...
Page 73: Wpa/Wpa2
Select WPA or WPA2 from the Security Mode list. Note: WPA or WPA2 is not available if you enable WPS before you configure WPA or WPA2 in the Wireless LAN > General screen. Figure 39 Network > Wireless LAN > General: WPA/WPA2 LTE3311 Series User’s Guide...
Page 74: More Ap Screen
This allows you to use one access point to provide several BSSs simultaneously. You can then assign varying security types to different SSIDs. Wireless clients can use different SSIDs to associate with the same access point. Click Network > Wireless LAN > More AP. The following screen displays. LTE3311 Series User’s Guide...
Page 75: More Ap Edit
7.4.1 More AP Edit Use this screen to edit an SSID profile. Click the Edit icon next to an SSID in the More AP screen. The following screen displays. Figure 41 Network > Wireless LAN > More AP: Edit LTE3311 Series User’s Guide...
Page 76: Mac Filter Screen
00:A0:C5:00:00:02. You need to know the MAC address of the devices to configure this screen. To change your LTE3311’s MAC filter settings, click Network > Wireless LAN > MAC Filter. The screen appears as shown. LTE3311 Series User’s Guide...
Page 77 Enter the MAC address of the wireless station that are allowed or denied access to the LTE3311. Apply Click Apply to save your changes back to the LTE3311. Cancel Click Cancel to reload the previous configuration for this screen. LTE3311 Series User’s Guide...
Page 78: Wireless Lan Advanced Screen
This specifies the time period before the device sends the beacon again. The interval tells receiving devices on the network how long they can wait in low-power mode before waking up to handle the beacon. A high value helps save current consumption of the access point. LTE3311 Series User’s Guide...
Page 79: Quality Of Service (Qos) Screen
Use this screen to enable/disable WPS, view or generate a new PIN number and check current WPS status. To open this screen, click Network > Wireless LAN > WPS. Note: With WPS, wireless clients can only connect to the wireless network using the first SSID on the LTE3311. LTE3311 Series User’s Guide...
Page 80 This is the name of the wireless network (the LTE3311’s first SSID). Security This is the type of wireless security employed by the network. Apply Click Apply to save your changes back to the LTE3311. Cancel Click Cancel to reload the previous configuration for this screen. LTE3311 Series User’s Guide...
Page 81: Wps Station Screen
Use this screen to set the times your wireless LAN is turned on and off. Wireless LAN scheduling is disabled by default. The wireless LAN can be scheduled to turn on or off on certain days and at certain times. To open this screen, click Network > Wireless LAN > Scheduling tab. LTE3311 Series User’s Guide...
Page 82: Wds Screen
7.11 WDS Screen A Wireless Distribution System (WDS) is a wireless connection between two or more APs. Use this screen to configure the LTE3311’s WDS settings. To open this screen, click Network > Wireless LAN > WDS tab. LTE3311 Series User’s Guide...
Page 83 You must also set the peer device to use the same pre-shared key. Apply Click Apply to save your changes back to the LTE3311. Reset Click Reset to reload the previous configuration for this screen. LTE3311 Series User’s Guide...
Page 84: Lan
8.3 What You Need To Know The actual physical connection determines whether the LTE3311 ports are LAN or WAN ports. There are two separate IP networks, one inside the LAN network and the other outside the WAN network as shown next. LTE3311 Series User’s Guide...
Page 85: Lan Ip Screen
IP address that you assign. Unless you are implementing subnetting, use the subnet mask computed by the LTE3311. Apply Click Apply to save your changes back to the LTE3311. Cancel Click Cancel to begin configuring this screen afresh. LTE3311 Series User’s Guide...
Page 86: Dhcp Server
9.2 DHCP Server General Screen The LTE3311 has built-in DHCP server capability that assigns IP addresses to systems that support DHCP client capability. Use this screen to enable the DHCP server. Click Network > DHCP Server. The following screen displays. LTE3311 Series User’s Guide...
Page 87 This field specifies the first of the contiguous addresses in the IP address pool for LAN. Address Pool Size This field specifies the size, or count of the IP address pool for LAN. DHCP Relay Select this option to have the LTE3311 forward DHCP requests to the DHCP server. LTE3311 Series User’s Guide...
Page 88: Dhcp Server Advanced Screen
MAC addresses. You can also use this screen to configure the DNS server information that the LTE3311 sends to the DHCP clients. To change your LTE3311’s static DHCP settings, click Network > DHCP Server > Advanced. The following screen displays. LTE3311 Series User’s Guide...
Page 89 DNS server (configured in the WAN screen) and relays the response back to the computer. Apply Click Apply to save your changes back to the LTE3311. Cancel Click Cancel to begin configuring this screen afresh. LTE3311 Series User’s Guide...
Page 90: Dhcp Client List Screen
Select this if you want to reserve the IP address for this specific MAC address. Apply Click Apply to save your changes back to the LTE3311. Cancel Click Cancel to reload the previous configuration for this screen. LTE3311 Series User’s Guide...
Page 91: Nat
92). • Use the Port Forwarding screen to set a default server and change your LTE3311’s port forwarding settings to forward incoming service requests to the server(s) on your local network (Section 10.3 on page 92). LTE3311 Series User’s Guide...
Page 92: General Screen
80 and FTP on port 21. In some cases, such as for unknown services or where one server can support more than one service (for example both FTP and web service), it might be better to specify a range of port numbers. LTE3311 Series User’s Guide...
Page 93 You can decide whether you want to use the default server or specify a server manually. Select this to use the default server. Change to Server Select this and manually enter the server’s IP address. LTE3311 Series User’s Guide...
Page 94: Port Forwarding Edit Screen
Click Cancel to begin configuring this screen afresh. 10.3.1 Port Forwarding Edit Screen This screen lets you edit a port forwarding rule. Click a rule’s Edit icon in the Port Forwarding screen to open the following screen. LTE3311 Series User’s Guide...
Page 95: Port Trigger Screen
10.4 Port Trigger Screen To change your LTE3311’s trigger port settings, click Network > NAT > Port Trigger. The screen appears as shown. Note: Only one LAN computer can use a trigger port (range) at a time. LTE3311 Series User’s Guide...
Page 96: Alg Screen
When the LTE3311 registers with the SIP register server, the SIP ALG translates the LTE3311’s private IP address inside the SIP data stream to a public IP address. You do not need to use STUN or an outbound proxy if your LTE3311 is behind a SIP ALG LTE3311 Series User’s Guide...
Page 97: Technical Reference
(such as a Web or FTP server) from your location. Your ISP may periodically check for servers and may suspend your account if it discovers any active services at your location. If you are unsure, refer to your ISP. LTE3311 Series User’s Guide...
Page 98: Nat Port Forwarding Example
This way you do not need to configure a new IP address each time you want a different LAN computer to use the application. 10.6.4 Trigger Port Forwarding Example The following is an example of trigger port forwarding. LTE3311 Series User’s Guide...
Page 99: Two Points To Remember About Trigger Ports
Trigger events only happen on data that is coming from inside the LTE3311 and going to the outside. If an application needs a continuous data stream, that port (range) will be tied up so that another computer on the LAN can’t trigger it. LTE3311 Series User’s Guide...
Page 100: Ddns
Table 42 Dynamic DNS LABEL DESCRIPTION IPv4 Dynamic DNS Setup Dynamic DNS Select Enable to use dynamic DNS. Select Disable to turn this feature off. Service Provider Select the name of your Dynamic DNS service provider. LTE3311 Series User’s Guide...
Page 101 This is the token authentication provided by the hosting provider (i.e. FreeDDNS). When the host name is registered, the hosting server provides the token identifier. Apply Click Apply to save your changes back to the LTE3311. Cancel Click Cancel to begin configuring this screen afresh. LTE3311 Series User’s Guide...
Page 102: Routing
R3 connected to the LAN. Figure 64 Example of Static Routing Topology 12.2 Static Route Screen Click Network > Routing > Static Route to open the Static Route screen. LTE3311 Series User’s Guide...
Page 103: Add/Edit Static Route
If you need to specify a route to a single host, use a subnet mask of 255.255.255.255 in the subnet mask field to force the network number to be identical to the host ID. LTE3311 Series User’s Guide...
Page 104: Dynamic Routing Screen
Select the RIP version from RIPv1 and RIPv2. Otherwise, select Disable to turn if off. Apply Click Apply to save your changes back to the LTE3311. Cancel Click Cancel to begin configuring this screen afresh. LTE3311 Series User’s Guide...
Page 105: Interface Group
This shows the descriptive name of the group. LAN Interface This shows the interface group. This shows the VLAN ID number (from 0 to 4094) of the interface group. Modify Click the Delete icon to remove the user-defined group. LTE3311 Series User’s Guide...
Page 106: Interface Group > Add Screen
Select the interfaces that you want and click the left arrow button to add them to this group. Back Click Back to quit and return to the previous screen. Apply Click Apply to save your changes back to the LTE3311. Cancel Click Cancel to exit this screen without saving. LTE3311 Series User’s Guide...
Page 107: Firewall
• Use the Services screen enable service blocking, enter/delete/modify the services you want to block and the date/time you want to block them (Section 14.3 on page 109). 14.1.2 What You Need To Know The following terms and concepts may help as you read through this chapter. LTE3311 Series User’s Guide...
Page 108: General Screen
Protect against IP spoofing by making sure the firewall is active. Keep the firewall in a secured (locked) room. 14.2 General Screen Use this screen to enable or disable the LTE3311’s firewall, and set up firewall logs. Click Security > Firewall to open the General screen. LTE3311 Series User’s Guide...
Page 109: Services Screen
You can also use this screen to enable service blocking, enter/delete/modify the services you want to block and the date/time you want to block them. Click Security > Firewall > Services. The screen appears as shown next. LTE3311 Series User’s Guide...
Page 110 Click Apply to save the settings. Add Firewall Rule Service Name Enter a name that identifies or describes the firewall rule. MAC Address Enter the MAC address of the computer for which the firewall rule applies. LTE3311 Series User’s Guide...
Page 111 DROP - Traffic matching the conditions of the firewall rule are stopped. Delete Click Delete to remove the firewall rule. Cancel Click Cancel to start configuring this screen again. Appendix D on page 216 for commonly used services and port numbers. LTE3311 Series User’s Guide...
Page 112: Content Filtering
Use this screen to restrict web features, and designate a trusted computer. You can also use this screen to configure URL filtering settings to block the users on your network from accessing certain web sites. Click Security > Content Filter to open the Content Filter screen. LTE3311 Series User’s Guide...
Page 113 Type a keyword in this field. You may use any character (up to 64 characters). Wildcards are not allowed. You can also enter a numerical IP address. Keyword List This list displays the keywords already added. LTE3311 Series User’s Guide...
Page 114 Apply. Clear All Click this button to remove all of the listed keywords. Apply Click Apply to save your changes. Reset Click Reset to begin configuring this screen afresh LTE3311 Series User’s Guide...
Page 115: Ipv6 Firewall
Click Apply to save the settings. Add Firewall Rule Service Name Enter a name that identifies or describes the firewall rule. MAC Address Enter the MAC address of the computer for which the firewall rule applies. LTE3311 Series User’s Guide...
Page 116 TCP port 80 defines web traffic. Action DROP - Traffic matching the conditions of the firewall rule is stopped. Delete Click Delete to remove the firewall rule. Cancel Click Cancel to restore your previously saved settings. LTE3311 Series User’s Guide...
Page 117: Voice Over Ip
For example, when you dial a number on your LTE3311, it sends a SIP message over the network asking the other device (the number you dialed) to take part in the call. LTE3311 Series User’s Guide...
Page 118: Before You Begin
17.3 VoIP General Screen Use this screen to enable VoIP and configure general VoIP settings on the LTE3311. To access this screen, click Application > Voice over IP > General. Figure 75 Application > Voice over IP > General LTE3311 Series User’s Guide...
Page 119: Phone Book Screen
17.4 Phone Book Screen Use this screen to manage your contact names and phone numbers. To access this screen, click Application > Voice over IP > Phone Book. Figure 76 Application > Voice over IP > Phone Book LTE3311 Series User’s Guide...
Page 120: Speed Dial Screen
SIP server. Enter the callee’s IP address or domain name. The LTE3311 sends SIP INVITE requests to the peer VoIP device when you use the speed dial entry. Figure 77 Application > Voice over IP > Speed Dial LTE3311 Series User’s Guide...
Page 121: Phone Conf. Screen
Click this to set every field in this screen to its last-saved value. 17.6 Phone Conf. Screen Use this screen to configure call features. To access this screen, click Application > Voice over IP > Phone Conf.. Figure 78 Application > Voice over IP > Phone Conf. LTE3311 Series User’s Guide...
Page 122: Call Feature Speed Dial Digits
Use this screen to view and change the key combinations you can enter on your phone’s keypad to use certain features. To access this screen, click Application > Voice over IP > Phone Conf. and then click the Call Feature Speed Dial Digits button. LTE3311 Series User’s Guide...
Page 123: Sip Configuration Screen
17.7 SIP Configuration Screen The LTE3311 uses a SIP account to make outgoing VoIP calls and check if an incoming call’s destination number matches your SIP account’s SIP number. In order to make or receive a VoIP LTE3311 Series User’s Guide...
Page 124 Click this to open a screen where you can maintain information about the SIP service Conf. domain. See Section 17.7.1 on page 125. Codec Conf. Click this to open a screen where you can configure codec priority. See Section 17.7.2 on page 126. LTE3311 Series User’s Guide...
Page 125: Service Domain Configuration
Enter the IP address or domain name of the SIP register server, if your VoIP service provider gave you one. Otherwise, enter the same address you entered in the Proxy Server field. You can use up to 95 printable ASCII characters. LTE3311 Series User’s Guide...
Page 126: Codec Configuration
Use this screen to maintain information about your SIP account, and configure the SIP server information. To access this screen, click Application > Voice over IP > SIP Conf. and then click the Codec Conf. button. Figure 82 Application > Voice over IP > SIP Conf.: Codec Conf. LTE3311 Series User’s Guide...
Page 127: Technical Reference
VoIP can use advanced voice coding techniques with compression to reduce the required bandwidth. The Session Initiation Protocol (SIP) is an application-layer control (signaling) protocol that handles the setting up, altering and tearing down of voice and multimedia sessions over the Internet. LTE3311 Series User’s Guide...
Page 128 SIP registrations (and subsequent SIP requests) require a username and password for authorization. These credentials are validated via a challenge / response system using the HTTP digest mechanism (as detailed in RFC3261, "SIP: Session Initiation Protocol"). LTE3311 Series User’s Guide...
Page 129 In the following example, you want to use client device A to call someone who is using client device The client device (A in the figure) sends a call invitation to the SIP proxy server (B). The SIP proxy server forwards the call invitation to C. Figure 84 SIP Proxy Server LTE3311 Series User’s Guide...
Page 130 When you make a VoIP call using SIP, the RTP (Real time Transport Protocol) is used to handle voice data transfer. See RFC 1889 for details on RTP. Pulse Code Modulation Pulse Code Modulation (PCM) measures analog signal amplitudes at regular time intervals and converts them into bits. LTE3311 Series User’s Guide...
Page 131 The following figure shows the SIP and session traffic flow between the user agents (UA 1 and UA 2) and the proxy servers (this example shows two proxy servers, PROXY 1 and PROXY 2). LTE3311 Series User’s Guide...
Page 132 User Agent 1 via Proxy 1. User Agent 2 sends an OK response to Proxy 2 after the call is answered. This is also relayed back to User Agent 1 via Proxy 1. LTE3311 Series User’s Guide...
Page 133 Enable Message Waiting Indication (MWI) enables your phone to give you a message–waiting (beeping) dial tone when you have a voice message(s). Your VoIP service provider must have a messaging system that sends message waiting status SIP packets as defined in RFC 3842. LTE3311 Series User’s Guide...
Page 134: Recording Custom Tones
Press a number from 1301~1308 followed by the “#” key to delete the tone of your choice. Press 14 followed by the “#” key if you wish to clear all your custom tones. LTE3311 Series User’s Guide...
Page 135: Quality Of Service (Qos)
DiffServ network. Based on the marking rule, different kinds of traffic can be marked for different priorities of forwarding. Resources can then be allocated according to the DSCP values and the configured policies. The LTE3311 does not support DiffServ at the time of writing. LTE3311 Series User’s Guide...
Page 136: Voice Over 3G
(Section 18.5 on page 139). 18.2 Vo3G General Screen Use this screen to enable Vo3G on the LTE3311. To access this screen, click Application > Voice over 3G > General. Figure 88 Application > Voice over 3G > General LTE3311 Series User’s Guide...
Page 137: Phone Book Screen
This field displays the index number of the contact. Name This field displays the name of the contact. Click Edit and enter the descriptive name of the contact. You can enter up to 40 characters for a contact. LTE3311 Series User’s Guide...
Page 138: Telephone Conf. Screen
LTE3311 makes the call immediately, instead of waiting. You can still wait, if you want. Apply Click this to save your changes and to apply them to the LTE3311. Cancel Click this to set every field in this screen to its last-saved value. LTE3311 Series User’s Guide...
Page 139: Call Configuration Screen
Note: If you enable the All Calls rule, other rules are not configurable/applicable. Apply Click this to save your changes and to apply them to the LTE3311. Cancel Click this to set every field in this screen to its last-saved value. LTE3311 Series User’s Guide...
Page 140: Sms
• Use the SMS screen to send new messages and view messages received on the LTE3311 (Section 19.2 on page 140). 19.2 SMS Screen Use this screen to send text messages using the LTE3311 and view messages received. To access this screen, click Application > SMS. LTE3311 Series User’s Guide...
Page 141 160 characters, more than one SMS will be sent. The maximum number of SMS that can be sent is 20 (1400 characters total). Result This shows whether the message is sent successfully. SMS Inbox List Refresh Click this button to update the list. LTE3311 Series User’s Guide...
Page 142 This field displays the content of the message. Preview Actions Click the delete icon to remove the message record. Apply Click this button to save your changes to the LTE3311. Refresh Click this button to update the screen. LTE3311 Series User’s Guide...
Page 143: Nas
This is a method of transferring data from one computer to another over a network such as the Internet. 20.1.3 Before You Begin Make sure the LTE3311 is connected to your network and turned on. Connect the USB device to one of the LTE3311’s USB ports. LTE3311 Series User’s Guide...
Page 144: File Sharing
Use this screen to set up file-sharing via the LTE3311 using Windows Explorer or the workgroup name. You can also configure the workgroup name. Click Applications > NAS > File Sharing to open the following screen. LTE3311 Series User’s Guide...
Page 145: Ftp Screen
Click Cancel to begin configuring this screen afresh. 20.3 FTP Screen Use this screen to set up file sharing via the LTE3311 using FTP. Click Application > NAS > FTP to open the following screen. Figure 95 Application > NAS > FTP LTE3311 Series User’s Guide...
Page 146: Example Of Accessing Your Shared Files From A Computer
Open Windows Explorer to access the connected USB device using either Windows Explorer browser or by browsing to your workgroup. Note: This example shows you how to use Microsoft’s Windows 7 to browse your shared files. Refer to your operating system’s documentation for how to browse your file structure. LTE3311 Series User’s Guide...
Page 147 You can also access files via the LTE3311 by browsing to the workgroup folder using the folder tree on the left side of the screen. It is located under Network. In this example the LTE3311’s name in a work group is the default “NAS” and the workgroup name is the default “WORKGROUP”. LTE3311 Series User’s Guide...
Page 148: Use Ftp To Share Files
You should have enabled file sharing in the Application > NAS > FTP screen. In your web browser’s address or URL bar type “ftp://” followed by the IP address of the LTE3311 (the default LAN IP address of the LTE3311 is 192.168.1.1) and click Go or press [ENTER]. LTE3311 Series User’s Guide...
Page 149 Chapter 20 NAS The screen changes and shows you the folder for the USB storage device connected to your LTE3311. Double-click the folder to display the contents in it. LTE3311 Series User’s Guide...
Page 150: Bandwidth Management
• Use the General screen to enable bandwidth management and assign bandwidth values (Section 21.4 on page 151). • Use the Advanced screen to configure bandwidth managements rule for the services and applications (Section 21.5 on page 152). LTE3311 Series User’s Guide...
Page 151: What You Need To Know
Select Enable to use up to 100% of the configured bandwidth. If you select Disable, Management you can only use up to 33% of the configured bandwidth. Apply Click Apply to save your customized settings. Cancel Click Cancel to begin configuring this screen afresh. LTE3311 Series User’s Guide...
Page 152: Advanced Screen
Click this button to remove all bandwidth management rules. 21.5.1 Add Bandwidth management Rule If you want to create a new bandwidth management rule for a service or application, click the Add New Rule icon in the Advanced screen. The following screen displays. LTE3311 Series User’s Guide...
Page 153 Select Single and each IP address in the rule can have the specified bandwidth. Apply Click Apply to save your customized settings. Cancel Click Cancel to exit this screen without saving. Appendix D on page 216 for commonly used services and port numbers. LTE3311 Series User’s Guide...
Page 154: Universal Plug-And-Play (Upnp)
When a UPnP device joins a network, it announces its presence with a multicast message. For security reasons, the LTE3311 allows multicast messages on the LAN only. LTE3311 Series User’s Guide...
Page 155: Upnp Screen
Make sure the computer is connected to a LAN port of the LTE3311. Turn on your computer and the LTE3311. 22.4.1.1 Auto-discover Your UPnP-enabled Network Device Click start and Control Panel. Double-click Network Connections. An icon displays under Internet Gateway. Right-click the icon and select Properties. LTE3311 Series User’s Guide...
Page 156 In the Internet Connection Properties window, click Settings to see the port mappings there were automatically created. Figure 102 Internet Connection Properties You may edit or delete the port mappings or click Add to manually add port mappings. Figure 103 Internet Connection Properties: Advanced Settings LTE3311 Series User’s Guide...
Page 157: Web Configurator Easy Access
LTE3311 first. This comes helpful if you do not know the IP address of the LTE3311. Follow the steps below to access the web configurator. Click Start and then Control Panel. Double-click Network Connections. LTE3311 Series User’s Guide...
Page 158 Right-click on the icon for your LTE3311 and select Invoke. The web configurator login screen displays. Figure 108 Network Connections: My Network Places Right-click on the icon for your LTE3311 and select Properties. A properties window displays with basic information about the LTE3311. LTE3311 Series User’s Guide...
Page 159 Chapter 22 Universal Plug-and-Play (UPnP) Figure 109 Network Connections: My Network Places: Properties: Example LTE3311 Series User’s Guide...
Page 160: Chapter 23 Tr-069
ACS and specify the ACS IP address or domain name and username and password. Click Management > TR-069 to open the following screen. Use this screen to configure your LTE3311 to be managed by an ACS. Figure 110 Management > TR-069 LTE3311 Series User’s Guide...
Page 161 When the ACS makes a connection request to the LTE3311, this password is used to authenticate the ACS. Interface Select a WAN interface through which the TR-069 traffic passes. Apply Click Apply to save your changes. Cancel Click Cancel to exit this screen without saving. LTE3311 Series User’s Guide...
Page 162: Maintenance
• Use the Restart screen to reboot the LTE3311 without turning the power off (Section 24.8 on page 169). 24.3 General Screen Use this screen to set the management session timeout period. Click Maintenance > General. The following screen displays. Figure 111 Maintenance > General LTE3311 Series User’s Guide...
Page 163: Account Screen
Click the Edit icon to edit this user account. 24.4.1 Edit a User Account Use this screen to edit a users account. Click the Edit icon next to the user account you want to configure. The screen shown next appears. LTE3311 Series User’s Guide...
Page 164: Time Setting Screen
Click Cancel to begin configuring this screen afresh. 24.5 Time Setting Screen Use this screen to configure the LTE3311’s time based on your local time zone. To change your LTE3311’s time and date, click Maintenance > Time. The screen appears as shown. LTE3311 Series User’s Guide...
Page 165 When you select Manual, enter the new date in this field and then click Apply. Get from Time Select this radio button to have the LTE3311 get the time and date from the time server Server you specified below. LTE3311 Series User’s Guide...
Page 166: Firmware Upgrade Screen
“*.bin” extension, e.g., “V1.00(AAYE.0).bin”. The upload process uses HTTP (Hypertext Transfer Protocol) and may take up to two minutes. After a successful upload, the system will reboot. Click Maintenance > Firmware Upgrade. Follow the instructions in this screen to upload firmware to your LTE3311. LTE3311 Series User’s Guide...
Page 167: Configuration Backup/Restore Screen
The backup configuration file will be useful in case you need to return to your previous settings. Restore configuration allows you to upload a new or previously saved configuration file from your computer to your LTE3311. LTE3311 Series User’s Guide...
Page 168 LTE3311 IP address (192.168.1.1). See Appendix C on page 190 for details on how to set up your computer’s IP address. LTE3311 Series User’s Guide...
Page 169: Restart Screen
System restart allows you to reboot the LTE3311 without turning the power off. Click Maintenance > Restart to open the following screen. Figure 118 Maintenance > Restart Click Restart to have the LTE3311 reboot. This does not affect the LTE3311's configuration. LTE3311 Series User’s Guide...
Page 170: Troubleshooting
Check the hardware connections. See the Quick Start Guide. Inspect your cables for damage. Contact the vendor to replace any damaged cables. Disconnect and re-connect the power adaptor to the LTE3311. If the problem continues, contact the vendor. LTE3311 Series User’s Guide...
Page 171: Lte3311 Access And Login
• If there is a DHCP server on your network, make sure your computer is using a dynamic IP address. See Section 8.4 on page • If there is no DHCP server on your network, make sure your computer’s IP address is in the same subnet as the LTE3311. See Section 8.4 on page LTE3311 Series User’s Guide...
Page 172: Internet Access
WAN screen. These fields are case-sensitive, so make sure [Caps Lock] is not on. Make sure your SIM card’s account is valid and has an active data plan. Check your service contract or contact your service provider directly. If the problem continues, contact your ISP. LTE3311 Series User’s Guide...
Page 173: Wireless Connections
Make sure the wireless adapter installed on your computer is IEEE 802.11 compatible and supports the same wireless standard as the LTE3311. Make sure your computer (with a wireless adapter installed) is within the transmission range of the LTE3311. LTE3311 Series User’s Guide...
Page 174: Getting More Troubleshooting Help
If the AP is placed at a high position, point the antennas downwards. Try pointing the antennas in different directions and check which provides the strongest signal to the wireless clients. 25.6 Getting More Troubleshooting Help Search for support information for your model at www.zyxel.com for more troubleshooting suggestions. LTE3311 Series User’s Guide...
Page 175: Appendix A Customer Support
• Brief description of the problem and the steps you took to solve it. Corporate Headquarters (Worldwide) Taiwan • ZyXEL Communications Corporation • http://www.zyxel.com Asia China • ZyXEL Communications (Shanghai) Corp. ZyXEL Communications (Beijing) Corp. ZyXEL Communications (Tianjin) Corp. • http://www.zyxel.cn India • ZyXEL Technology India Pvt Ltd • http://www.zyxel.in Kazakhstan •...
Page 176 • ZyXEL Singapore Pte Ltd. • http://www.zyxel.com.sg Taiwan • ZyXEL Communications Corporation • http://www.zyxel.com/tw/zh/ Thailand • ZyXEL Thailand Co., Ltd • http://www.zyxel.co.th Vietnam • ZyXEL Communications Corporation-Vietnam Office • http://www.zyxel.com/vn/vi Europe Austria • ZyXEL Deutschland GmbH • http://www.zyxel.de Belarus • ZyXEL BY • http://www.zyxel.by...
Page 177 Appendix A Customer Support Belgium • ZyXEL Communications B.V. • http://www.zyxel.com/be/nl/ • http://www.zyxel.com/be/fr/ Bulgaria • ZyXEL България • http://www.zyxel.com/bg/bg/ Czech Republic • ZyXEL Communications Czech s.r.o • http://www.zyxel.cz Denmark • ZyXEL Communications A/S • http://www.zyxel.dk Estonia • ZyXEL Estonia • http://www.zyxel.com/ee/et/ Finland •...
Page 178 • ZyXEL Communications Poland • http://www.zyxel.pl Romania • ZyXEL Romania • http://www.zyxel.com/ro/ro Russia • ZyXEL Russia • http://www.zyxel.ru Slovakia • ZyXEL Communications Czech s.r.o. organizacna zlozka • http://www.zyxel.sk Spain • ZyXEL Communications ES Ltd • http://www.zyxel.es Sweden • ZyXEL Communications • http://www.zyxel.se Switzerland •...
Page 179 Appendix A Customer Support • http://www.zyxel.ch/ Turkey • ZyXEL Turkey A.S. • http://www.zyxel.com.tr • ZyXEL Communications UK Ltd. • http://www.zyxel.co.uk Ukraine • ZyXEL Ukraine • http://www.ua.zyxel.com Latin America Argentina • ZyXEL Communication Corporation • http://www.zyxel.com/ec/es/ Brazil • ZyXEL Communications Brasil Ltda.
Page 180 Appendix A Customer Support North America • ZyXEL Communications, Inc. - North America Headquarters • http://www.zyxel.com/us/en/ Oceania Australia • ZyXEL Communications Corporation • http://www.zyxel.com/au/en/ Africa South Africa • Nology (Pty) Ltd. • http://www.zyxel.co.za LTE3311 Series User’s Guide...
Page 181: Appendix B Pop-Up Windows, Javascript And Java Permissions
PP EN D I X Pop-up Windows, JavaScript and Java Permissions In order to use the web configurator you need to allow: • Web browser pop-up windows from your device. • JavaScript (enabled by default). • Java permissions (enabled by default). Note: The screens used below belong to Internet Explorer version 6, 7 and 8.
Page 182 Appendix B Pop-up Windows, JavaScript and Java Permissions Figure 120 Internet Options: Privacy Click Apply to save this setting. Enable Pop-up Blockers with Exceptions Alternatively, if you only want to allow pop-up windows from your device, see the following steps. In Internet Explorer, select Tools, Internet Options and then the Privacy tab.
Page 183 Appendix B Pop-up Windows, JavaScript and Java Permissions Figure 121 Internet Options: Privacy Type the IP address of your device (the web page that you do not want to have blocked) with the prefix “http://”. For example, http://192.168.167.1. Click Add to move the IP address to the list of Allowed sites. Figure 122 Pop-up Blocker Settings LTE3301 Series User’s Guide...
Page 184 Appendix B Pop-up Windows, JavaScript and Java Permissions Click Close to return to the Privacy screen. Click Apply to save this setting. JavaScript If pages of the web configurator do not display properly in Internet Explorer, check that JavaScript are allowed. In Internet Explorer, click Tools, Internet Options and then the Security tab.
Page 185 Appendix B Pop-up Windows, JavaScript and Java Permissions Figure 124 Security Settings - Java Scripting Java Permissions From Internet Explorer, click Tools, Internet Options and then the Security tab. Click the Custom Level... button. Scroll down to Microsoft VM. Under Java permissions make sure that a safety level is selected. Click OK to close the window.
Page 186 Appendix B Pop-up Windows, JavaScript and Java Permissions Figure 125 Security Settings - Java JAVA (Sun) From Internet Explorer, click Tools, Internet Options and then the Advanced tab. Make sure that Use Java 2 for <applet> under Java (Sun) is selected. Click OK to close the window.
Page 187 Appendix B Pop-up Windows, JavaScript and Java Permissions Mozilla Firefox Mozilla Firefox 2.0 screens are used here. Screens for other versions may vary slightly. The steps below apply to Mozilla Firefox 3.0 as well. You can enable Java, Javascript and pop-ups in one screen. Click Tools, then click Options in the screen that appears.
Page 188 Appendix B Pop-up Windows, JavaScript and Java Permissions Opera Opera 10 screens are used here. Screens for other versions may vary slightly. Allowing Pop-Ups From Opera, click Tools, then Preferences. In the General tab, go to Choose how you prefer to handle pop-ups and select Open all pop-ups.
Page 189 Appendix B Pop-up Windows, JavaScript and Java Permissions Figure 130 Opera: Enabling Java To customize JavaScript behavior in the Opera browser, click JavaScript Options. Figure 131 Opera: JavaScript Options Select the items you want Opera’s JavaScript to apply. LTE3301 Series User’s Guide...
Page 190: Appendix C Setting Up Your Computer's Ip Address
PP EN D I X Setting Up Your Computer’s IP Address Note: Your specific LTE3301 may not support all of the operating systems described in this appendix. See the product specifications for more information about which operating systems are supported. This appendix shows you how to configure the IP settings on your computer in order for it to be able to communicate with the other devices on your network.
Page 191 Appendix C Setting Up Your Computer’s IP Address In the Control Panel, click the Network Connections icon. Right-click Local Area Connection and then select Properties. On the General tab, select Internet Protocol (TCP/IP) and then click Properties. LTE3301 Series User’s Guide...
Page 192 Appendix C Setting Up Your Computer’s IP Address The Internet Protocol TCP/IP Properties window opens. LTE3301 Series User’s Guide...
Page 193 Appendix C Setting Up Your Computer’s IP Address Select Obtain an IP address automatically if your network administrator or ISP assigns your IP address dynamically. Select Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields if you have a static IP address that was assigned to you by your network administrator or ISP.
Page 194 Appendix C Setting Up Your Computer’s IP Address Click the Network and Sharing Center icon. Click Manage network connections. Right-click Local Area Connection and then select Properties. Note: During this procedure, click Continue whenever Windows displays a screen saying that it needs your permission to continue. Select Internet Protocol Version 4 (TCP/IPv4) and then select Properties.
Page 195 Appendix C Setting Up Your Computer’s IP Address The Internet Protocol Version 4 (TCP/IPv4) Properties window opens. LTE3301 Series User’s Guide...
Page 196 Appendix C Setting Up Your Computer’s IP Address Select Obtain an IP address automatically if your network administrator or ISP assigns your IP address dynamically. Select Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields if you have a static IP address that was assigned to you by your network administrator or ISP.
Page 197 Appendix C Setting Up Your Computer’s IP Address Click Change adapter settings. Double click Local Area Connection and then select Properties. LTE3301 Series User’s Guide...
Page 198 Appendix C Setting Up Your Computer’s IP Address Note: During this procedure, click Continue whenever Windows displays a screen saying that it needs your permission to continue. Select Internet Protocol Version 4 (TCP/IPv4) and then select Properties. The Internet Protocol Version 4 (TCP/IPv4) Properties window opens. LTE3301 Series User’s Guide...
Page 199 Appendix C Setting Up Your Computer’s IP Address Select Obtain an IP address automatically if your network administrator or ISP assigns your IP address dynamically. Select Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields if you have a static IP address that was assigned to you by your network administrator or ISP.
Page 200 Appendix C Setting Up Your Computer’s IP Address Mac OS X: 10.3 and 10.4 The screens in this section are from Mac OS X 10.4 but can also apply to 10.3. Click Apple > System Preferences. In the System Preferences window, click the Network icon. LTE3301 Series User’s Guide...
Page 201 Appendix C Setting Up Your Computer’s IP Address When the Network preferences pane opens, select Built-in Ethernet from the network connection type list, and then click Configure. For dynamically assigned settings, select Using DHCP from the Configure IPv4 list in the TCP/IP tab.
Page 202 Appendix C Setting Up Your Computer’s IP Address For statically assigned settings, do the following: • From the Configure IPv4 list, select Manually. • In the IP Address field, type your IP address. • In the Subnet Mask field, type your subnet mask. •...
Page 203 Appendix C Setting Up Your Computer’s IP Address Figure 132 Mac OS X 10.4: Network Utility Mac OS X: 10.5 and 10.6 The screens in this section are from Mac OS X 10.5 but can also apply to 10.6. Click Apple > System Preferences. In System Preferences, click the Network icon.
Page 204 Appendix C Setting Up Your Computer’s IP Address When the Network preferences pane opens, select Ethernet from the list of available connection types. From the Configure list, select Using DHCP for dynamically assigned settings. LTE3301 Series User’s Guide...
Page 205 Appendix C Setting Up Your Computer’s IP Address For statically assigned settings, do the following: • From the Configure list, select Manually. • In the IP Address field, enter your IP address. • In the Subnet Mask field, enter your subnet mask. •...
Page 206 Appendix C Setting Up Your Computer’s IP Address Figure 133 Mac OS X 10.5: Network Utility Linux: Ubuntu 8 (GNOME) This section shows you how to configure your computer’s TCP/IP settings in the GNU Object Model Environment (GNOME) using the Ubuntu 8 Linux distribution. The procedure, screens and file locations may vary depending on your specific distribution, release version, and individual configuration.
Page 207 Appendix C Setting Up Your Computer’s IP Address In the Authenticate window, enter your admin account name and password then click the Authenticate button. In the Network Settings window, select the connection that you want to configure, then click Properties. LTE3301 Series User’s Guide...
Page 208 Appendix C Setting Up Your Computer’s IP Address The Properties dialog box opens. • In the Configuration list, select Automatic Configuration (DHCP) if you have a dynamic IP address. • In the Configuration list, select Static IP address if you have a static IP address. Fill in the IP address, Subnet mask, and Gateway address fields.
Page 209 Appendix C Setting Up Your Computer’s IP Address Click the Close button to apply the changes. Verifying Settings Check your TCP/IP properties by clicking System > Administration > Network Tools, and then selecting the appropriate Network device from the Devices tab. The Interface Statistics column shows data if your connection is working properly.
Page 210 Appendix C Setting Up Your Computer’s IP Address Figure 134 Ubuntu 8: Network Tools Linux: openSUSE 10.3 (KDE) This section shows you how to configure your computer’s TCP/IP settings in the K Desktop Environment (KDE) using the openSUSE 10.3 Linux distribution. The procedure, screens and file locations may vary depending on your specific distribution, release version, and individual configuration.
Page 211 Appendix C Setting Up Your Computer’s IP Address When the Run as Root - KDE su dialog opens, enter the admin password and click OK. When the YaST Control Center window opens, select Network Devices and then click the Network Card icon. LTE3301 Series User’s Guide...
Page 212 Appendix C Setting Up Your Computer’s IP Address When the Network Settings window opens, click the Overview tab, select the appropriate connection Name from the list, and then click the Configure button. When the Network Card Setup window opens, click the Address tab LTE3301 Series User’s Guide...
Page 213 Appendix C Setting Up Your Computer’s IP Address Figure 135 openSUSE 10.3: Network Card Setup Select Dynamic Address (DHCP) if you have a dynamic IP address. Select Statically assigned IP Address if you have a static IP address. Fill in the IP address, Subnet mask, and Hostname fields.
Page 214 Appendix C Setting Up Your Computer’s IP Address Click Finish to save your settings and close the window. Verifying Settings Click the KNetwork Manager icon on the Task bar to check your TCP/IP properties. From the Options sub-menu, select Show Connection Information. Figure 136 openSUSE 10.3: KNetwork Manager When the Connection Status - KNetwork Manager window opens, click the Statistics tab to see if your connection is working properly.
Page 215 Appendix C Setting Up Your Computer’s IP Address Figure 137 openSUSE: Connection Status - KNetwork Manager LTE3301 Series User’s Guide...
Page 216: Appendix D Common Services
PP EN D I X Common Services The following table lists some commonly-used services and their associated protocols and port numbers. For a comprehensive list of port numbers, ICMP type/code numbers and services, visit the IANA (Internet Assigned Number Authority) web site. •...
Page 217 Appendix D Common Services Table 81 Commonly Used Services (continued) NAME PROTOCOL PORT(S) DESCRIPTION HTTPS HTTPS is a secured http session often used in e- commerce. ICMP User-Defined Internet Control Message Protocol is often used for diagnostic or routing purposes. 4000 This is a popular Internet chat program.
Page 218 Appendix D Common Services Table 81 Commonly Used Services (continued) NAME PROTOCOL PORT(S) DESCRIPTION SQL-NET 1521 Structured Query Language is an interface to access data on many different types of database systems, including mainframes, midrange systems, UNIX systems and network servers. TCP/UDP Secure Shell Remote Login Program.
Page 219: Appendix E Legal Information
The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved.
Page 220: European Union
Directivei 1999/5/EC. Slovenčina ZyXEL týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/EC. (Slovak) Slovenščina ZyXEL izjavlja, da je ta oprema v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/EC. (Slovene) LTE3311 Series User’s Guide...
Page 221 2. The regulatory limits for maximum output power are specified in EIRP. The EIRP level (in dBm) of a device can be calculated by adding the gain of the antenna used(specified in dBi) to the output power available at the connector (specified in dBm). LTE3311 Series User’s Guide...
Page 222: Safety Warnings
If this product is end of life, take it to a recycling station designated by local authorities. At the time of disposal, the separate collection of your product and/or its battery will help save natural resources and ensure that the environment is sustainable development. LTE3311 Series User’s Guide...
Page 223 återvinningsstation. Vid tiden för kasseringen bidrar du till en bättre miljö och mänsklig hälsa genom att göra dig av med den på ett återvinningsställe. LTE3311 Series User’s Guide...
Page 224 Appendix E Legal Information Environmental Product Declaration LTE3311 Series User’s Guide...
Page 225: Appendix E Legal Information
To obtain the services of this warranty, contact your vendor. You may also refer to the warranty policy for the region in which you bought the device at http://www.zyxel.com/web/support_warranty_info.php. Registration Register your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products. LTE3311 Series User’s Guide...
Page 226 This product contains in part some free software distributed under GPL license terms and/or GPL like licenses. Open source licenses are provided with the firmware package. You can download the latest firmware at www.zyxel.com. To obtain the source code covered under those Licenses, please contact support@zyxel.com.tw to get it. LTE3311 Series User’s Guide...
Page 227: Index
Index Index ACK message Daylight saving DDNS see also Dynamic DNS ActiveX service providers 100, 115 Address Assignment DHCP 48, 86 Auto Configuration Server, see ACS DHCP server see also Dynamic Host Configuration Protocol DHCP server 85, 86 differentiated services DiffServ (Differentiated Services) Bandwidth management code points...
Page 228 Index file sharing Java example overview Samba Windows Explorer work group IP pool setup Firewall LAN overview guidelines ICMP packets LAN setup firewall Language stateful inspection Link type Firmware upload local (user) database file extension and encryption using HTTP Local Area Network firmware version logout Web Configurator...
Page 229 Index server sets remote management TR-069 NAT Traversal Remote Procedure Calls, see RPCs Navigation Panel Reset button navigation panel Reset the device Network Address Translation 91, 92 Restore configuration non-proxy calls RFC 1889 Roaming RPPCs RTS/CTS Threshold 65, 78 OK response 131, 132 other documentation Samba...
Page 230 Index static route voice coding configuration VoIP Status peer-to-peer calls Subnet Mask Summary DHCP table Packet statistics 48, 50 Wireless station status WAN (Wide Area Network) System General Setup warranty System restart note Web Configurator how to access Overview web configurator TCP/IP configuration Web Proxy Time setting...

ZyXEL Communications LTE3311 series User Manual

Contents Overview

Table of Contents

User's Guide

PART I User's Guide

Chapter 1 Introduction

Chapter 2 Introducing the Web Configurator

Chapter 3 Setup Wizard

Chapter 4 Tutorials

Technical Reference

Part II: Technical Reference

Chapter 5 Monitor

Chapter 6 WAN

Chapter 7 Wireless LAN

Chapter 8 LAN

Chapter 9 DHCP Server

Chapter 10 NAT

Chapter 11 DDNS

Chapter 12 Routing

Chapter 13 Interface Group

Chapter 14 Firewall

Chapter 15 Content Filtering

Chapter 16 Ipv6 Firewall

Chapter 17 Voice over IP

Chapter 18 Voice over 3G

Chapter 19 SMS

Chapter 20 NAS

Chapter 21 Bandwidth Management

Chapter 22 Universal Plug-And-Play (Upnp)

Chapter 23 TR-069

Chapter 24 Maintenance

Chapter 25 Troubleshooting

Appendix A Customer Support

Appendix B Pop-Up Windows, Javascript and Java Permissions

Appendix C Setting up Your Computer's IP Address

Appendix D Common Services

Appendix E Legal Information

Appendix E Legal Information

Index

Quick Links

Troubleshooting

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ZyXEL Communications LTE3311 series

Summary of Contents for ZyXEL Communications LTE3311 series