Section 3
Installation
3.1 Installing UV System
Electronic controller must be connected to a Ground Fault Protected Circuit (GFCI) receptacle.
Prerequisites:
•
Determine appropriate indoor location of the controller and chamber, refer to
•
Make sure that the controller is installed higher than the chamber and away from all water sources.
•
Ensure adequate clearance above chamber to allow for removal of the lamp and sleeve.
•
Make sure to turn off the main water supply.
•
Make all necessary plumbing connections refer to
Procedure:
1
2
• Install the UV Chamber
• Connect Flow Meter Sensor
vertically with the following
(PRO10,20,30 models only)
spacing on the wall using
to chamber using 1¼" unions
screws.
supplied.
• PRO10: 18.5"
Note: LED must face up.
• H, PRO20: 27.5"
Ensure proper length of
straight pipe 1.0" Diameter at
• K, PRO30/50: 37.5"
inlet side of Flow Meter
Note: Ensure chamber is
Sensor and use a 1¼" to 1"
installed with green arrows
Reducing Coupler (not
pointing upwards.
supplied).
5
6
• Insert sleeve with arrow
• Wet O-ring with water then
pointing up.
place over top end of sleeve.
Note: DO NOT rotate sleeve
and touch glass with bare
hands.
C A U T I O N
Section
2.1.
Section
2.1.
4
3
• Connect the sleeve bolt at the
• Install the sensor to the UV
bottom of the sleeve
system (for PRO models
assembly. Ensure sleeve bolt
only).
is rotated full 1/4 turn until
Note: DO NOT use wrench to
positive stop.
7
8
2
1
• Connect the sleeve bolt to the
• Remove the sleeve bolt at the
top of the sleeve assembly.
bottom of the sleeve
Ensure sleeve bolt is rotated
assembly.
full 1/4 turn until positive stop.
Installation
Mantenimiento
Procedimiento:
1
1
• Extraiga el perno de la vaina
tubular de la parte superior
del conjunto de la vaina
tubular.
5
2
• Quite la vaina tubular.
1
9
• Vuelva a instalar la vaina
tubular con la flecha
orientada hacia arriba.
2
1
Nota: NO gire la vaina tubular
ni toque el cristal con las
manos sin protección.
8
53
2
3
2
3
2
1
• Quite el tornillo del perno de
• Inserte la herramienta de
la vaina tubular.
extracción de la vaina tubular
en la parte inferior de la vaina
• Extraiga el perno de la vaina
tubular.
tubular en la parte inferior del
conjunto de vaina tubular.
6
7
• Quite la junta tórica de la
• Limpie la vaina tubular con un
parte superior de la vaina
trapo empapado en CLR,
tubular.
vinagre u otro ácido blando y
luego aclárela con agua.
• Quite la junta tórica de la parte
inferior de la cámara
Nota: Si no es posible limpiar
(es posible que se caiga
la vaina tubular por completo
durante el proceso de
o si se raya o se quiebra,
extracción de la vaina tubular).
reemplácela.
11
11
10
10
• Vuelva a instalar las nuevas
• Conecte el perno de la vaina
juntas tóricas lubricadas
tubular en la parte superior
sobre la parte superior de la
del conjunto de vaina tubular.
vaina tubular.
4
• Levante la vaina tubular hasta
que se suelte.
• Coloque un cubo debajo de la
cámara UV, ya que saldrá
agua.
8
1
2
3
Mild
Acid
• Conecte el perno de la vaina
tubular en la parte inferior del
conjunto de vaina tubular.
12
12
2
1
2
1
• Extraiga el perno de la vaina
tubular en la parte inferior del
conjunto de vaina tubular.