Section 6 Troubleshooting; Sección 2 Información General - Viqua H, K Owner's Manual

Section 6 Troubleshooting
Symptom Possible Cause
GFCI and/or breaker tripped
Controller fuse has blown
No power
Transient voltage surge suppressor (TVSS) damaged
Controller damaged
Connection between lamp and lamp plug is wet
GFCI or breaker repeatedly
trips Short-circuit in the electrical assembly
Leak at inlet or outlet Threaded pipe fittings are leaking
Condensation of moist air on cold chamber (slow
accumulation)
Leak detected from area of UV
O-ring damaged, deteriorated or incorrectly installed
chamber
Lamp/sleeve assembly not properly installed (too tight or not
tight enough)
Alarm Refer to Section 5.1.
Equipment downstream of UV system is acting as a breeding
System is operating but water
ground for pathogens
tests reveal bacterial
Pathogens are residing in the distribution lines post-UV
contamination
Recontamination from pipe dead-ends
Detect Flow Sensor not detecting flow
Flow Meter Sensor red status
LED Flow Meter Sensor not functioning
6.1 LOW UV ALARMS (PRO and Plus Series Only)
UV Sensor
Yes
Is There a
LED Flashing
Flow Meter
Flow Meter LED
Amber
Red
Turn Off
Clean System
Water Supply
Run @
Power
75-100%
Reset
rated flow
Green
Normal
UV Sensor
UV Sensor Clean System
Operation
LED
LED
Red
Amber Green
Check
Clean UV Sensor
UVT LED
System
Green
Address UVT Flow water
UVT @ 70%
Issue
rated flow
<75%
>75%
Red
Check
Sensor
Change
LED UVT
Sensor
Green
Run @
UVT
75-100%
>75%
rated flow
Green
Change
Sensor
Normal Sensor
Operation LED
Red
Sensor
LED
Green
Change
Lamp
Change Lamp
Figure 4 Low UV Alarms (PRO and Plus Series Only)
Possible Solution
Reset GFCI and/or breaker
Replace controller fuse - see Fuse Replacement section
(Refer Section 4.3).
Replace TVSS
Replace controller and use a TVSS
Clean and dry lamp pins and lamp plug, check unit for leaks
or condensation
Replace controller
Clean threads, reseal with Teflon tape and retighten
Control humidity or relocate unit
Inspect and replace if deteriorated
Ensure nut is turned completely
Refer to Section 5.1.
Ensure UV is the last piece of treatment equipment
Ensure all distribution lines have been disinfected with
chlorine. Refer to Section 3.2.
Remove any pipe dead-ends and flush with chlorine. Refer to
Section 3.2.
Increase Flow rate through meter
Flow Meter requires maintenance or replacement
Low UV
Alarms
No
Clean System
Red
Red
Run System Sensor Change Sensor
LED Sensor LED
Dry
Green Green
Normal
Introduce
Operation
Water
>75%
Red <75%
Sensor
Change Check UVT UVT
LED
Lamp
Red
Green
Red
Change
UV Sensor
Sensor
LED Normal
Green Operation
Normal
Operation
Address UVT
Issue
<75%
Red
Troubleshooting Información general
Sección 2
Elemento
Change
Lamp
1 Controlador
Address UVT
Issue
2 Perno superior y forma de alambre
3 Lámpara
4 Vaina tubular
5 Ventilador CoolTouch
6 Cámara
7 Junta tórica
16 45
Información general
1
14
13
7
12
11
10
9
Figura 1 Componentes del sistema
Descripción N.º pieza
650709-003
650709-006
650709-009
660020-R
650709-005
660019-R
650709-004
660018-R
602916 y 602896
602854
602855
602856
602974
602975
602976
650630
-
002233
2
3
4
5
6
7
8
Sistemas UV
PRO10
PRO20
PRO30
PRO50
H Plus
K Plus
H
K
Se utiliza en todos los sistemas
PRO10
PRO20, H Plus, H
PRO30/50, K Plus, K
PRO10
PRO20, H Plus, H
PRO30/50, K Plus, K
Se utiliza en todos los sistemas
Se utiliza en todos los sistemas
Se utiliza en todos los sistemas