Control Panel; Operation - Viqua H, K Owner's Manual

8 Perno inferior (incluye tornillo) 603053
Herramienta de extracción de la vaina
9 602988
tubular
410982R-10
Sensor de medidor de flujo 
10 410982R-20
(solo modelos PRO)
410982R-30
11 Sensor 650580
12 Tapón -
602636
13 Cable de alimentación
602637
14 Cable de la lámpara -
2.1 Dimensiones y distribución
A B
C
14
15
ENTRADA
1 2
Figura 2 Sistema: dimensiones y distribución
Elemento Descripción
1 Válvula de muestra
2 Válvula de corte
3 Tratamiento previo
4 Válvula de corte de desvío:
5 Válvula de corte
Se utiliza en todos los sistemas
Se utiliza en todos los sistemas
PRO10
PRO20
PRO30
Modelos PRO y Plus
Modelos básicos
110 V: se utiliza en todos los sistemas
220 V: se utiliza en todos los sistemas
Se utiliza en todos los sistemas
Distancia para
D
extracción de
la lámpara
SALIDA
L
11
13 6
12
10
183 cm (72")
8 9 L
Ø
4
5 7
10"
S
1"
16
3
Función
Permite realizar una muestra del agua sin tratar.
Facilita las tareas de mantenimiento del equipo de tratamiento previo.
El tratamiento previo permite el funcionamiento eficaz del sistema UV. El agua debe
satisfacer determinados parámetros de calidad antes de acceder al sistema UV.
La línea y válvula de desvío son opcionales. Están diseñadas para proporcionar un
suministro de agua de emergencia cuando el sistema UV no esté disponible.
Se requiere para permitir realizar las tareas de mantenimiento del sistema UV.
Información general

Operation

Section 5

5.1 Control Panel

Feature
A Mute
B New Lamp
LED
Solenoid valve open
1
(If equipped with solenoid)
2 Operating normally
3 Operating normally
Operating normally
4
Note: During the lamp warm up, the
indicator will flash
UV dose is adequate and sensor is
5 operating normally (For Plus Models
only)
6 Flow Meter operating normally
46 15
Operation
1
3
4
5
6
A
B
Figure 3 Control Panel
Buttons and Display
Description
Press to silence audible alarm.
When the alarm is due to the lamp's age, the mute button will silence the audible alarm for 7 days; this
may be repeated up to a maximum of 4 times. After that, the button will silence for only 24 hours.
When the alarm is due to any other issue, the mute button will silence the audible alarm for 24 hours.
After installing a new lamp, press and hold for five seconds to reset Lamp timer to 365.
Indicator Lights
Green Yellow
Solenoid valve disconnected;
reconnect.
Not applicable
Solenoid coil damaged; replace coil (not
entire solenoid).
Lamp connector not installed properly.
Ensure lamp harness ground is inserted
Not applicable
into chamber ground terminal.
Controller failure, replace controller
Fan disconnected, reconnect.
Fan turning slower than required;
Not applicable unplug system, clean blades using a
Q-tip
Fan damaged, replace fan.
Lamp disconnected; remove power,
Warning: Lamp will require reconnect lamp and connect the
controller.
replacement shortly
Lamp failure, replace lamp
Sensor disconnected; unplug system,
reconnect sensor and plug-in system
again
UV dose is near the
Sensor failure
minimum required
UV dose is below minimum required,
see Low UV Alarm section
High flow UV dose
inadequate, reduce flow to
Flow meter sensor failure; service or
achieve higher dose levels
replace sensor
(PRO10, PRO20, and
PRO30 only)
2
Function
Flashing red Solid red
Solenoid valve inactive (closed)
due to failure of another
component, in order to ensure
safety of the water supply
Lamp inactive due to controller
failure.
Not applicable
Lamp inactive due to controller
failure
Sensor inactive due to lamp or
controller failure
Low flow UV dose inadequate,
service required.