Radio Systems Requirements; Recommended Setup-2-Stroke Glow; Recommended Setup-4-Stroke Glow; Recommended Setup-Electric Power (Ep) - Hangar 9 toledo special 40 Assembly Manual

Radio Systems Requirements

Spektrum Radio System
• DX6i 6-channel radio or greater with receiver
(SPM6600)
• JRPS821 DS821 Digital Sport Servo (5)
(4 required for EP version)
• JSP98110 6-inch Servo Extension (2)
• JSP98020 Y-Harness or JSP98110 6-inch Servo
Extension (2) for receiver to aileron servos
• JR Switch, Chargeswitch (JRPA004)
• Receiver battery, 2700mAh
Optional
• JSP98020 Y-Harness or JSP98110 6-inch
Servo Extension to connect the float rudder
servo to the receiver.
Recommended Setup–2-Stroke glow
• Evolution .46NX with Muffler (EVOE0461)
®
• Evolution Propeller 11 x 5 (EVO11050) to
11 x 6 (EVO11060)
Recommended Setup–4-Stroke glow
• Saito ™ .82 AAC w/Muffler (SAIE082AGK or SAIE082A)
• Evolution Propeller 13 x 8 (EVO13080) or
14 x 6 (EVO14060)
Recommended Setup–
Electric Power (EP)
• E-flite Power 46 BL Outrunner Motor (EFLM4046A)
®
• 60-Amp Pro Switch-Mode BEC Brushless ESC
(EFLA1060)
• Thunder Power 4S 3850–4500mAh LiPo Battery Pack
• APC Propeller 13x6.5-inch (APC13065E) to
14x7 (APC14070E)

Field Equipment Required

• Fuel (15% recommended)
• Propeller
• Long Reach Glow Plug Wrench (HAN2510)
• Metered Glow Driver w/Ni-Cd & Charger (HAN7101)
• 2-Cycle Sport Plug (EVOGP1)
• Manual Fuel Pump (HAN118)
4

optional Field Equipment

• Self-stick weights, 6 oz (HAN3626)
• PowerPro 12V Starter (HAN161)
• 12V 7Ah Sealed Battery (HAN102)
• Power Panel (HAN106)
• Blue Block After Run Oil (EVOX1000)
• Cleaner and towels

Additional Required Tools

Drill File
Pin drill Pliers
Ruler Scissors
Side cutters Flat blade screwdriver
Hobby knife with #11 blade Small clamps
Medium grit sandpaper Z-bend Pliers (HAN119)
Phillips screwdriver: #1, #2 Hook and loop tape
Low-Tack Tape (MMM209034)
Box wrench to fit propeller nut
Box end or open end wrench: 1/4-inch, 7/16-inch,
1/2-inch
Hex wrench or ball driver: 3/32-inch
Drill bit: 5/64-inch (2mm), 5/32-inch (4mm)

Additional Required Adhesives

Canopy Glue (PAAPT56)
Medium CA (PAAPT02)
Thin CA (PAAPT08)
Threadlock (PAAPT42)
30-Minute Epoxy, 8 oz (PAAPT39)
FS one®
With FS One (HANS2000) you get more than photorealistic
fields, gorgeous skies and realistic-looking aircraft. You get
incredibly advanced aerodynamic modeling that simulates
every possible aspect of real-world flight.
The first Hangar Pack (HANS4010) will add even more
®
aircraft to FS One. This latest edition includes ten new planes
and helis from your favorite brands, including Hangar 9,
E-flite and Align. You'll be able to fly aircraft that are only
available on FS One such as the T-REX, Blade CX2, Blade CP
Pro, Hangar 9 P-51 and F-22 PTS. And as always, with the
Hangar Pack, you still get all the same great features that
you did with the original aircraft.
HANS2008 HANS4010
Important Information
Regarding Warranty Information
Please read our Warranty and Liability Limitations section on
Page 33 before building this product. If you as the purchaser
or user are not prepared to accept the liability associated
with the use of this Product, you are advised to return this
Product immediately in new and unused condition to the
place of purchase.
The Spektrum trademark is used with permission
of Bachmann Industries, Inc.
Hangar 9 Toledo Special Assembly Manual