Technical Specifications; Configurations Of Terminals - Eiki EK-100W Owner's Manual

Technical Specifications

LCD system XGA: 0.63" TFT, active matrix, 3-panel
WXGA: 0.59" TFT active matrix, 3-panel
LCD resolution XGA: 1024X768 / WXGA: 1280X800
Compatible signals
Color standard PAL, SECAM, NTSC, NTSC4.43, PAL-M, PAL-N and PAL60
HDTV signal 480i, 480p, 576i, 576p, 720p, 1080i and 1080p
Scanning frequency Horizontal frequency: 15 kHz –100 KHz; Vertical frequency: 48 – 85 Hz
Optical elements
Image size (diagonal lines) 30"-300", adjustable
XGA: 0.9m-9.1m(W) 1.1m-10.9m(T)
Projection distance
WXGA: 0.9m-9.6m(W) 1.1m-11.6m(T)
Lens F=1.6-1.76, f=19.158-23.018mm; Manual zooming and focusing;
Zoom Ratio: 1.2x optics
Lamp Consumption(W) 218W
Terminal
VGA IN 1/YPbPr/S-VIDEO IN Mini D-sub 15 pin x1
VGA IN 2/VGA OUT Mini D-sub 15 pin x1
HDMI HDMI A type 19 pin x2 (one is compatible with MHL)
LAN 100 Base-TX (100Mbps)/10 Base-T (10Mbps) RJ45
USB-B x1(display / Firmware upgrade)
USB-A x1(picture viewer / wifi dongle(optional))
RS-232 D-sub 9 pin x1
AUDIO OUT 3.5mm Mini Type Stereo x1
AUDIO IN 3.5mm Mini Type Stereo x1
Composit Video 2RCA (L/R) x1
RCA x1
Power
Voltage and power consumption AC 100–240 V, 50/60 Hz
Fuse 250V/10A
Internal speaker 10W RMS 8ohm, x1
Operating Environment
Operating temperature 41˚F-104˚F (5˚C - 40˚C)
Storage Temperature -4˚F-140˚F (-20˚C - 60˚C)
High land 1400 m - 2700 m
Remote control
Battery AAA or LR3 1.5V ALKALINE TYPE x 2
Operating Range 16.4' (5 m)/±30
Dimensions 50mm (W) x 18mm (H) x 110mm (D)
Net Weight 50g (including batteries)
Mechanical properties
Dimensions (W×H×D ) 347.0mmx110.3mmx257.0mm
Net Weight 3.2Kg
Adjustable foot 40mm
Accessories
AC Power Cord, Remote Control & battery, VGA Cable
Quick Start Guide, Warranty Card (U.S.A.)
● The specification is subject to change without prior notice.
● Liquid crystal panel is made on the basis of high standard, where 99.99% of the pixels are effective.
Due to the nature of the liquid crystal panel, a fraction of the pixels (0.01% or less) may be ineffective.
78
Appendix
Appendix

Configurations of terminals

terminal pin assignments and signal names
COMPUTER IN 1
1 R/Pr/S-C
2 G/Y/S-Y
3 B/Pb/-
11 12 13 14 15
4 -----
6 7 8 9 10
5 GND
1 2 3 4 5
6 GND
7 GND
8 GND
Note:
The Pin 1, 2 and 3 (Pr, Y, Pb): for YCbCr/YPbPr signal.
The Pin 1 and 2 (S-C, S-Y): for S-Video signal.
COMPUTER IN 2/COMPUTER OUT terminal pin assignments and signal names
1 R
2 G
3 B
11 12 13 14 15
4 -----
6 7 8 9 10
5 GND
1 2 3 4 5
6 GND
7 GND
8 GND
RS232 terminal (D-SUB-9 pin)
1 -----
2 RXD
6 7 8 9
3 TXD
1 2 3 4 5
4 -----
5 GND
6 -----
7 -----
8 -----
9 -----
HDMI terminal pin assignments and signal names
1 T.M.D.S data2+
2 T.M.D.S data2 shield
2 4 6 8 10 12 14 16 18
3 T.M.D.S data2–
1 3 5 7 9 11 13 15 17 19
4 T.M.D.S data1+
5 T.M.D.S data1 shield
6 T.M.D.S data1–
7 T.M.D.S data0+
8 T.M.D.S data0 shield
9 T.M.D.S data0–
10 T.M.D.S clock+
USB-B terminal
1 V Bus
2 Data -
1 2
3 Data +
4 3
4 GND
9 +5V
10 GND
11 GND
12 DDC data
13 HD/SYNC
14 VD
15 DDC clock
9 NC
10 GND
11 -----
12 DDC data
13 HD/SYNC
14 VD
15 DDC clock
LAN terminal
1 TX + 5 -----
2 TX - 6 -----
3 ----- 7 RX +
4 ----- 8 RX -
8 7 6 5 4 3 2 1
11 T.M.D.S clock shield
12 T.M.D.S clock–
13 CEC
14 -----
15 SCL
16 SDA
17 DDC/CEC GND
18 +5V
19 Hot plug detection
79