Eiki EK-100W Owner's Manual page 11

Basic operation
Turn on the projector
1. Complete peripheral connections (with a
computer, video,etc.) before turning on the
projector.
2. Connect the projector's AC power cord into
the AC outlet. The POWER indicator turns
red.
3. Press the POWER button on the top control
or on the remote control. The POWER
indicator becomes green and the cooling
fans start to work. The preparation display
appears on the screen.
4. If the projector is locked with a PIN code, a
PIN code input dialog box appears. Enter
the PIN code as instructed below.
 Note:
● When the logo select is set to be "Off", the
logo will not be displayed on the screen.(See
page 46)
Enter a PIN code
Press the OK button, press ◄► button to
select a number and press the OK button to
enter it to the PIN code box, then number
changes to "*", automatically move the cursor
to next box. If you fixed an incorrect number,
press MENU button to reset it again.
Repeat the steps to complete entering a three-
digit number.
After entering the three-digit number,
automatically move the cursor to "Set", press
the OK button then you can start to operate the
projector.
If you entered an incorrect "PIN code", the
number (***) turn red. PIN code will be reset
within one second automatically, Enter the
correct PIN code all over again.
What is PIN code?
PIN (Personal Identification Number) code is a
security code that allows the person who knows
it to operate the projector. Setting the PIN code
can prevent unauthorized use of the projector.
A PIN code consists of a three-digit number.
Refer to the PIN code lock function in the
"Expand" "Security" menu on page 47 for PIN
code lock operation of the projector.
20
16
PIN Code
Set
Cancel
----- Input PIN code Back
OK Esc
PIN Code
*
Set
Cancel
Move Select Back
OK Esc
Move the cursor to "Set", and press "OK".
Caution on handling the PIN code
If you forget your PIN code, the
projector can no longer be started.
Take a special care in setting a
new PIN code. Write down the
number in a column on page 81 of
this manual and keep it properly.
Should the PIN code be missing
or forgotten, consult your dealer or
service center.
Basic operation
Turn off the projector
1. Press the POWER button on the top control
or on the remote control, and "Power off?"
appears on the screen.
2. Then, press the POWER button again in 4
seconds. The POWER indicator starts to
flash red, and the cooling fans keep running
(You can select the fan noise and running
speed). Now you can unplug the AC power
cord after the fans stop running. Otherwise,
the service life of the projector will be
affected or the projector will can not be
turned on or turn on abnormal.
3 When the projector has cooled down enough
to be turned on again, the POWER indicator
stops flashing.
To maintain the lamp life, once you turn
the projector on, wait at least 5 minutes
before turning it off.
Do not operate the projector continuously
without reset. Continuous use may result
in shortening the lamp life. Turn off the
projector and let it standby for about an
hour in every 24 hours.
 Note:
● When the On start function is "On" , this
projector is turned on automatically by
connecting the AC power cord to an AC outlet .
● The running speed of cooling fans is changed
according to the temperature inside the
projector.
● Do not put the projector in a case before it is
cooled enough.
● If the POWER indicator flashes or emits a
red light, see page 76.
● While the POWER indicator is flashing, the
lamp is being cooled down and the projector
cannot be turned on. Wait until the POWER
indicator turns red to turn on the projector again.
● The fan rotation will terminate directly if the
AC power cord is unplugged immediately
after the projector is turned off.
● The projector can be turned on after the
POWER indicator turns red. The waiting time
to restart will be shortened when the normal
power-off processing for fan cooling is
completed, comparing with the time the AC
power cord is immediately unplugged after the
power-off.
Power off ?
"Power off ? " disappears after 4 seconds.
21