Page 2
VOD (Video on demand) and SNMP RMON management and Web-based Switch network management. The Dynamix 24 VDSL IP DSLAM is a bridge between external Internet backbone through a router for IP sharing and the building 110D telephone rack mount or telephone box. It utilizes the available telephone wire to enable high-speed Internet access to...
Page 3
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 VDSL IP DSLAM uses the phone line networking technology endorsed by the VDSL (Very High Data Rate DSL), Dynamix DV-24 and the 24 ports VDSL IP DSLAM utilizes the already existing telephone wire to deliver 5/15/25 Mbps Internet access on each RJ-21 port.
Page 4
24 Ports VDSL + 2 Giga Ethernet The Dynamix DV-24 VDSL IP DSLAM provide 1 x RJ-21 (24 x POTS Ports) with splitter on board, 1 x RJ-21 (24 x VDSL Ports) and 2 x 10/100/1000Mbps auto-sensing RJ-45. The 24 ports VDSL IP DSLAM is a rack-unit (1.5RU) high, 299 mm deep.
ATM-based xDSL solutions. • Speed Rate Control: Dynamix DV-24 VDSL IP DSLAM supports speed rate control function, from 100kbps to 5/15/25Mbps. • IEEE-802.1x: port base network access control, this function for wireless users connecting Authentication •...
Page 6
• Alarm: In order to make sure the system is working normally, the Dynamix DV-24 provides Fan and Temperature monitor and management, you can see through WEB or Telnet which shows the internal temperature and fan speed, if the temperature exceeds 70°C or the fan stops working, the VDSL IP DSLAM will send a SNMP trap to inform the...
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Safety Warnings For your safety, be sure to read and follow all warning notices and instructions before device use. • DO NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel can service the device.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Table of Contents 1. Unpacking Information ..............................10 Check List..................................10 2. Installing the IP DSLAM..............................11 Hardware Installation................................ 11 Pre-installation Requirements ............................11 General Rules..................................12 Connecting the IP DSLAM..............................12 Connecting Ethernet Port..............................
Page 9
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.3.4 TFTP Backup ................................28 4.4 Web Administrator Management ..........................29 4.4.1 IP Address ................................29 4.4.2 Switch Settings ................................ 30 4.4.3 Port Controls ................................33 4.4.4 Trunking..................................34 4.4.5 Filter Database .................................
Page 10
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Appendix E: Troubleshooting............................79 Diagnosing VDSL Indicators............................79 System Diagnostics ................................81 Appendix F: Compliance and Safety Information ......................83 Warranty .................................... 86...
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 1. Unpacking Information Check List Carefully unpack the package and check its contents against the checklist. Package Contents • 24 ports VDSL IP DSLAM • User Manual CD •...
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 2. Installing the IP DSLAM Hardware Installation This chapter describes how to install the 24 ports VDSL IP DSLAM to establish network connection. You may install the IP DSLAM on any level surface (table, shelf, 19 inch rack or wall mounting). However, please take note of the following minimum site requirements before you begin.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 General Rules Before making any connections to the IP DSLAM, note the following rules: • Ethernet Port (RJ-45) All network connections to the IP DSLAM Ethernet port must be made using Category 5 UTP for 100Mbps, Category 3, 4 UTP for 10Mbps.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Connecting Ethernet Port Ethernet Port “25” and “26” support auto MDI/MDIX. You can connect the “25 or 26” port on the IP DSLAM to any device that uses a standard network interface such as a Cable modem, ADSL modem, Ethernet Switch, workstation or server, or also to a network interconnection device such as a bridge or router (depending on the port type implemented).
Page 15
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Notes: Be sure each twisted-pair cable (RJ-45) does not exceed 100 meters (333 feet). RJ-11 port use 18 ~ 26 gauge phone wiring, we do not recommend 28 gauge or above. We advise using Category 5 cable for Cable Modem or Router connections to avoid any confusion or inconvenience in the future when you upgrade attached to high bandwidth devices.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 3. Hardware Description This section describes the important parts of the Dynamix DV-24. It features the front indicators and rear connectors. Front Panel The following figure shows the front panel.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Front Indicators The Dynamix DV-24 VDSL IP DSLAM has many LED indicators. The following Table shows the description. LED Indicators Description and Operation LEDs Color Status Descriptions The device is receiving the power and functioning properly.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Rear Panel The following figure shows the rear connectors. Rear connectors The power cord should be plugged into AC Power Socket. It accepts AC power from 100 to 240 voltages.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4. Management Configuration 4.1 In-Band Management Console Port (RS-232) Configuration (Change IP Address via Hyper-Terminal) 1. Connect IP DSLAM with PC/Laptop’s RS-232 port, using “Hyper-Terminal” in the Windows™ system. Set “Bits per second”...
Page 20
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 2. After login window show on the screen, it will ask for Login Name and Password. Login Name: admin, Password: 123 Main Manual window will show on the screen as the following: Operation: Arrow/Tab/Backspace = Move light bar to select Item Enter = Select Item...
Page 21
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 3. Set IP Address: (1) Select “Switch Static Configuration” to enter the Switch Configuration page. (2) Select “Administration Configuration” to enter the Device Configuration page...
Page 22
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 (3) Select “IP Configuration” to enter the IP configuration page...
Page 23
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 (4) In the “IP Configuration”, it allows user to setup the DHCP, IP Address, Subnet Mask and Gateway. a. Select <Edit> to Change IP address, Subnet Mask and Gateway b.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.2 Remote Network Management IP Setting It must assign an IP for the IP DSLAM via the console port (RS-232 Port) before users configure the VDSL IP DSLAM via Telnet and Web.
Page 25
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 2. Network control by “WEB” The 24 ports VDSL IP DSLAM provides WEB UI to manage the device. The default configurations are as follows: Default IP Address: 192.168.16.250 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.16.1 User Name: admin...
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.3 Web Basic Management 4.3.1 Port Status This page can see every port status that depended on user setting and the negotiation result. 1. State: Display port statuses disable or enable. “Unlink” will be treated as “off”. 2.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.3.2 Port Statistics The following information provides a view of the current status of the unit. Press “Reset” button to clean all counts.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.3.3 TFTP Update The following menu functions allow user update the firmware and remote boot device: 1. Install TFTP Server and execution. 2. Copy firmware update version image.bin to TFTP Server directory. 3.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.3.4 TFTP Backup TFTP Restore Configuration Use this function to set TFTP server address. User can restore EEPROM value from here, but before the IP DSLAM restore the flash image file, the image file must store in TFTP server. TFTP Backup Configuration Use this function to set TFTP server IP address.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4 Web Administrator Management 4.4.1 IP Address 1. User can configure the IP Settings and fill the new values in here.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.2 Switch Settings Basic Description: Display the name of device type. MAC Address: The unique hardware address assigned by manufacturer (default) Firmware Version: Display the device’s Firmware version. Hardware version: Display the device’s Hardware version.
Page 32
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 When broadcast traffic for a port rises above the threshold you set, broadcast storm control becomes active. Priority Queue Service settings First Come First Service: The sequence of packets sent is depend on arrive order. All High before Low: The high priority packets sent before low priority packets.
Page 33
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Collisions Retry Forever: Enable or Disable Collisions Retry Forever. Hash Algorithm: Select in CRC-Hash mode or Direct Map mode 802.1x Protocol: Enable or disable 802.1x Protocol.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.3 Port Controls This section shows you how to change every port status and speed mode. 1. State: User can disable or enable this port control. 2. Negotiation: User can set auto negotiation mode is Auto, Force of per port, Nway (specify the speed/duplex on this port and enable auto-negotiation).
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.4 Trunking The Link Aggregation Control Protocol (LACP) provides a standardized means for exchanging information between Partner Systems on a link to allow their Link Aggregation Control instances to reach agreement on the identity of the Link Aggregation Group to which the link belongs, move the link to that Link Aggregation Group, and enable its transmission and reception functions in an orderly manner.
Page 36
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Aggregator setting System Priority: A value used to identify the active LACP. The switch with the lowest value has the highest priority and is selected as the active LACP. 1.
Page 37
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Aggregator Information When you are setting LACP aggregator, you can see relation information in here. 1. This page is no group active. LACP don’t working. 2. This page is Static Trunking group.
Page 38
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 State Activity Active (select): The port automatically sends LACP protocol packets. Passive (no select): The port does not automatically sends LACP protocol packets, and responds only if it receives LACP protocol packets from the opposite device.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.5 Filter Database IGMP Snooping The 24 ports VDSL IP DSLAM supports IP multicast, you can enable IGMP protocol on web management’s switch setting advanced page, then display the IGMP snooping information in this page, you can view difference multicast group, VID and member port in here, IP multicast addresses range from 224.0.0.0 through 239.255.255.255.
Page 40
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 IP manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP allows the ports to detect IGMP queries and report packets and manage IP multicast traffic through the switch. IGMP have three fundamental types of message as follows: Message Description...
Page 41
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Static MAC Addresses New entry of static address can be added and list can be defined to the address table.
Page 42
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 MAC filtering MAC address filtering allows the switch to drop unwanted traffic. Traffic is filtered based on the destination addresses. 1. In the MAC Address box, enter the MAC address that wants to filter. 2.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.6 VLAN Config A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network traffic so only members of the VLAN receive traffic from the same VLAN members. Basically, creating a VLAN from a switch is logically equivalent of reconnecting a group of network devices to another Layer 2 switch.
Page 44
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Port-based VLAN Packets can go among only members of the same VLAN group. Note all unselected ports are treated as belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging is ignored.
Page 45
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 1. Click Add to create a new VLAN group. 2. Enter the VLAN name, group ID and select the members for the new VLAN, then click Apply. 3. If the VLAN groups over the page’s limitation, user can use “Next Page” to view other VLAN groups. NOTE: If the trunk groups exist, it (ex: TRK1, TRK2…) will show in select menu of ports, and user can set it in the member of the VLAN or not.
Page 46
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Tag-based VLAN (IEEE 802.1Q VLAN) Tagged-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create a VLAN across devices from different switch venders. IEEE 802.1Q VLAN uses a technique to insert a “tag” into the Ethernet frames. Tag contains a VLAN Identifier (VID) that indicates the VLAN numbers.
Page 47
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 802.1Q VLAN This page, user can create Tag-based VLAN, and enable or disable GVRP protocol. There are 256 VLAN groups to provide configure. Enable 802.1Q VLAN, the all ports on the switch belong to default VLAN, VID is 1.
Page 48
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 GVRP (GARP [Generic Attribute Registration Protocol] VLAN Registration Protocol) GVRP allows automatic VLAN configuration between the switch and nodes. If the 24 ports VDSL IP DSLAM is connected to a device with GVRP enabled, you can send a GVRP request using the VID of a VLAN defined on the 24 ports VDSL IP DSLAM, the 24 ports VDSL IP DSLAM will automatically add that device to the existing VLAN.
Page 49
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 The 24-ports VDSL IP DSLAM has 16 PVID ranges. PVID of Port 1 ~ Port 26 must be in the same range. Num. PVID Range Num. PVID Range Num.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.7 Spanning Tree The Spanning-Tree Protocol (STP) is a standardized method (IEEE 802.1D) for avoiding loops in switched networks. When STP enabled, to ensure that only one path at a time is active between any two nodes on the network. You can enable Spanning-Tree Protocol on web management’s switch setting advanced item, select enable Spanning-Tree protocol.
Page 51
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Parameter Description You can change priority value, A value used to identify the root bridge. The bridge Priority with the lowest value has the highest priority and is selected as the root. Enter a number 1 through 65535.
Page 52
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 The following parameter can be configured on each port Parameter Description Define the priority of each port, the rage is from 0 to 255, the lower number has Port Priority the higher priority.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.8 Port Sniffer The Port Sniffer is a method for monitor traffic in switched networks. Traffic through ports can be monitored by one specific port. That is, traffic goes in or out monitored ports will be duplicated into sniffer port. 1.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.9 SNMP Any Network Management running the simple Network Management Protocol (SNMP) can manage the switch, provided the Management Information Base (MIB) is installed correctly on the management station. The SNMP is a Protocol that governs the transfer of information between management and agent.
Page 55
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 2. Community strings serve as passwords and can be entered as one of the following: RO: Read only. Enables requests accompanied by this string to display MIB-object information. RW: Read write.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.10 Security Manager Using this page, user can change web management user name and password. 1. User name: Type the new user name. 2. Password: Type the new password. 3.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.11 802.1X Config System Configuration 802.1x makes using of the physical access characteristics of IEEE802 LAN infrastructures in order to provide a means of authenticating and authorizing devices attached to a LAN port that has point-to-point connection characteristics, and of preventing access to that port in cases in which the authentication and authorization process fails.
Page 58
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Misc Configuration In this page, you can change the default configuration for the 802.1x standard: Quiet Period: used to define periods of time during which it will not attempt to acquire a supplicant (Default •...
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.12 Modem Location This function allows for the identification of the location of each Remote Modem. In the text box to a port, type the location of the Remote Modem for that port. The field is limited to alphanumeric characters and hyphen, and will accept a maximum 10 characters.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.13 Interleave This function is used in digital data transmission technology to protect the transmission against noise issue and data error. If during transit more than a certain amount of data has been lost then the data cannot be correctly decoded. Short bursts of noise on the line can cause these data packets to become corrupt and the modem has to re-request data which in turn can slow down the overall rate at which data is transmitted.
Page 61
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 If your line is particularly susceptible to bursts of noise then interleaving should improve your vdsl experience simply because if you lose a whole batch of data then this could cause your modem to loose sync with the exchange. Using Interleaving, the modem is able to re-assemble the data or if necessary just re-request the part of the data that it is unable to recover.
Page 62
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 The following ports can modify the desired interleave depth. The current information provides a view of the current status of the unit. Interleave depth value will show in the state only if the port is connected.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 4.4.14 Reset System Reset 24 ports VDSL IP DSLAM to default configuration. 4.4.15 Reboot Reboot the 24 ports VDSL IP DSLAM in software reset.
24 ports VDSL IP DSLAM (the high-speed VDSL fabric). Transceiver function The Dynamix DV-24 VD SL IP DSLAM supports Ethernet to VDSL convert and it can be transmit or receive packet from Ethernet port to the RJ21 port or VDSL port to Ethernet port.
Page 65
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Used as Apartment for Internet Access The Dynamix DV-24 VDSL IP DSLAM provides a high speed, 5/15/25Mbps transmission over existing home telephone wiring over a single Internet account to provide simultaneous independent Internet access to multiple users.
Page 66
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Application for sharing a single internet account If multiple users would like to share a single internet account using the 24 ports VDSL IP DSLAM, which is to be connected to a IP sharing device, then to a xDSL or Cable Modem.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Appendix C: Product Specification Key Features & Benefits • Supports bandwidth management (speed rate control) 5M/15M/25Mbps for VDSL port with long driver capable up to 1.7/1.1/0.6Km (5666/3666/1999 feet) •...
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Product Specification Standard: IEEE802.3 standard IEEE802.3u standard IEEE802.3ab standard Compliant with ETSI, ITU, ANSI standards Interface: 2 * RJ-45 10/100/1000Mbps Ethernet port 24 * RJ-21 connector for VDSL connection 24 * RJ-21 connector for POTS/ISDN connection Flow control: Full duplex: IEEE 802.3x...
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Appendix D: Example of VLAN Setting Example 1: 4 users join to Internet by VDSL system like following drawing, and have 7 demands. User A connects to port 1 and join to Internet through port 26 User B connects to port 2 and join to Internet through port 26 User C connects to port 3 and join to Internet through port 26 User D connects to port 4 and join to Internet through port 26...
Page 73
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Add VLAN Group: There are 256 VLAN groups available for configuration. Add a VLAN Group VID=21 member ports = port 1 & port 26 Note: Do not change the default_1 group.
Page 74
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Setup VLAN Name=UserA, VID=21, select member ports 1 & 26 Select Untag or Tag Setup. Unless the device (computer or switch) which connect to port 1 or port 26 can support Tagging VLAN, otherwise select Untag.
Page 75
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Add a VLAN Group Name=UserB, VID=22 member ports = port 2 & port 26 Add a VLAN Group Name=UserCD, VID=23 member ports = port 3, port 4 & port 26...
Page 76
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Example 2: 4 users join to Internet through 2 IP DSLAMs like the following drawing, and have 7 demands. User A connect to port 1 of VDSL-1 and join to Internet through port 26 of VDSL-2 User B connect to port 2 of VDSL-1 and join to Internet through port 26 of VDSL-2 User C connect to port 1 of VDSL-2 and join to Internet through port 26 of VDSL-2 User D connect to port 2 of VDSL-2 and join to Internet through port 26 of VDSL-2...
Page 77
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Setup Procedure: VDSL-1 SETUP: a. Setup Port VID: Port 1 PVID=11, Port 2 PVID=12 b. Add VLAN Group: Note: Do not change the default_1 group. Add a VLAN Group, Group name=UserA VID=11 member ports = port 1 & port 26 Select Untag or Tag Setup for VID=11 group: Port Number Untag/Tag Select...
Page 78
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 VDSL-2 SETUP: a. Setup Port VID: Port 1 PVID=21, Port 2 PVID=12 b. Add VLAN Group: Do not change the default_1 group. Add a VLAN Group, Group name=UserA VID=11 member ports = port 25 & port 26 Select Untag or Tag Setup for VID=11 group: Port Number Untag/Tag Select...
Page 79
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Add a VLAN Group, Group name=UserC VID=21 member ports = port 1 & port 26 Select Untag or Tag Setup for VID=21 group: Port Number Untag/Tag Select Untag Untag...
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Appendix E: Troubleshooting Diagnosing VDSL Indicators The VDSL can be easily monitored through its comprehensive panel indicators. These indicators assist the network manager in identifying problems of the IP DSLAM may encounter. This section describes common problems you may encounter and possible solutions.
Page 81
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 3. Symptom: VDSL Link cannot be established. Cause: VDSL speed mode setting failure or phone cable length is over the specification limit of the speed mode. Solution: 3.1 Please make sure that the phone wire must be connected between NVF-200LS and NVF-200R when both are power on.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 System Diagnostics Power and Cooling Problems If the POWER indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply as explained in the previous section.
Page 83
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Cabling 1. Verify that the cable type is correct. Be sure RJ-45 cable connectors are securely seated in the required ports. Use 100Ω straight-through cables for all standard connections. Use Category 5 cable for 100/1000Mbps Fast Ethernet connections, or Category 3, 4 or 5 cables for standard 10Mbps Ethernet connections.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Appendix F: Compliance and Safety Information FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a computing device, pursuant to Part 15 of FCC rules.
Page 85
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance in order for you to make necessary modifications to maintain uninterrupted service.
Page 86
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
24VDSL+2Giga Ethernet Managed 4 Band VDSL IP DSLAM USER’S MANUAL Ver. A.4 Warranty The original owner that the product delivered in this package will be free from defects in material and workmanship for one year parts after purchase. There will be a minimal charge to replace consumable components, such as fuses, power transformers, and mechanical cooling devices.